Nissan Qashqai J11. Manual - part 1696

B1C02 REAR HEIGHT SENSOR SIGNAL

EXL-85

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace harness.

7.

CHECK INSTALLATION OF HEIGHT SENSOR

Check height sensor is properly installed. Refer to 

EXL-169, "Exploded View"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace malfunctioning parts and perform sensor initialize. Refer to 

EXL-74, "Work Pro-

cedure"

.

8.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Connect IPDM E/R connector and height sensor connector.

2.

Turn ignition switch ON.

3.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

4.

Touch “ERASE” to erase DTC memory of IPDM E/R.

5.

Turn ignition switch OFF.

6.

Perform DTC confirmation procedure. Refer to 

EXL-83, "DTC Description"

.

Is DTC detected again?

YES

>> GO TO 9.

NO

>> INSPECTION END

9.

REPLACE HEIGHT SENSOR

With CONSULT

1.

Replace height sensor. Refer to 

EXL-170, "Removal and Installation"

.

2.

Turn ignition switch ON.

3.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

4.

Touch “ERASE” to erase DTC memory of IPDM E/R.

5.

Turn ignition switch OFF.

6.

Perform DTC confirmation procedure. Refer to 

EXL-83, "DTC Description"

.

Is DTC detected again?

YES

>> Replace IPDM E/R. Refer to 

PCS-67, "Removal and Installation"

.

NO

>> INSPECTION END

EXL-86

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

B1C07 AIMING MOTOR DRIVE SIGNAL

B1C07 AIMING MOTOR DRIVE SIGNAL

DTC Description

INFOID:0000000010452532

DTC DETECTION LOGIC

POSSIBLE CAUSE

[CIRC SHORT TO GRND]

• Harness or connector
• Headlamp aiming motor
• IPDM E/R

[CIRC SHORT TO BATTERY]

• Harness or connector
• Headlamp aiming motor
• IPDM E/R

[SIGNAL COMPARE FAILURE]

• Harness or connector
• Headlamp aiming motor
• IPDM E/R

FAIL-SAFE

Right and left headlamp aiming motors stop at the position when DTC is detected.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch ON.

2.

Turn lighting switch 2ND and wait at least 2 seconds or more.

3.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

4.

Check DTC.

Is DTC detected?

YES

>> Refer to 

EXL-86, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010452533

1.

CHECK DTC

Perform each inspection according to the displayed DTC.

Which DTC is displayed?

[CIRC SHORT TO GRND]>>GO TO 2.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B1C07

AIMING MOTOR DRIVE SIGNAL
(Aiming motor drive signal)

[CIRC 
SHORT TO 
GRND]

When ignition switch is ON, headlamp (LO) ON condi-
tions are satisfied, and the aiming motor drive signal volt-
age that is output to the headlamp aiming motor is 1.25 V 
or less continually for 2 seconds or more.

[CIRC 
SHORT TO 
BATTERY]

When ignition switch is ON, headlamp (LO) ON condi-
tions are satisfied, and the aiming motor drive signal volt-
age that is output to the headlamp aiming motor is 11.25 
V or more continually for 2 seconds or more.

[SIGNAL 
COMPARE 
FAILURE]

When ignition switch is ON, headlamp (LO) ON condi-
tions are satisfied, and the difference between the calcu-
lated value and actual output value for the aiming motor 
drive signal voltage that is output to the headlamp aiming 
motor is 1.75 V or more continually for 2 seconds or more.

B1C07 AIMING MOTOR DRIVE SIGNAL

EXL-87

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

[CIRC SHORT TO BATTERY]>>GO TO 3.
[SIGNAL COMPARE FAILURE]>>GO TO 4.

2.

CHECK AIMING MOTOR DRIVE SIGNAL CIRCUIT (SHORT TO GROUND)

1.

Turn ignition switch OFF.

2.

Turn lighting switch OFF.

3.

Disconnect the following connectors.

-

IPDM E/R

-

Headlamp aiming motor LH

-

Headlamp aiming motor RH

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

3.

CHECK AIMING MOTOR DRIVE SIGNAL CIRCUIT (SHORT TO BATTERY)

1.

Turn ignition switch OFF.

2.

Turn lighting switch OFF.

3.

Disconnect the following connectors.

-

IPDM E/R

-

Headlamp aiming motor LH

-

Headlamp aiming motor RH

4.

Check the voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

4.

CHECK AIMING MOTOR DRIVE SIGNAL

With CONSULT

1.

Select “OPTIC AXIS ACTIVE TEST” in “Active Test” mode of “IPDM E/R” using CONSULT.

2.

With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 6.

5.

CHECK AIMING MOTOR DRIVE SIGNAL CIRCUIT (OPEN)

1.

Turn ignition switch OFF.

2.

Disconnect the following connectors.

-

IPDM E/R

-

Headlamp aiming motor LH

IPDM E/R

—

Continuity

Connector

Terminal

E101

56

Ground

Not existed

+

-

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

E101

56

Ground

0 V

+

-

Test item

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

E101

56

Ground

OPTIC AXIS 
ACTIVE TEST

Default

3.54 V

Lower

11.07 V

EXL-88

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

B1C07 AIMING MOTOR DRIVE SIGNAL

-

Headlamp aiming motor RH

3.

Check continuity between IPDM E/R harness connector and headlamp aiming motor harness connector.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Connect IPDM E/R connector and headlamp aiming motor connector.

2.

Turn ignition switch ON.

3.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

4.

Touch “ERASE” to erase DTC memory of IPDM E/R.

5.

Turn ignition switch OFF.

6.

Perform DTC confirmation procedure. Refer to 

EXL-86, "DTC Description"

.

Is DTC detected again?

YES

>> GO TO 7.

NO

>> INSPECTION END

7.

REPLACE HEADLAMP AIMING MOTOR

With CONSULT

1.

Replace headlamp aiming motor. Refer to 

EXL-162, "Disassembly and Assembly"

.

2.

Turn ignition switch ON.

3.

Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.

4.

Touch “ERASE” to erase DTC memory of IPDM E/R.

5.

Turn ignition switch OFF.

6.

Perform DTC confirmation procedure. Refer to 

EXL-86, "DTC Description"

.

Is DTC detected again?

YES

>> Replace IPDM E/R. Refer to 

PCS-67, "Removal and Installation"

.

NO

>> INSPECTION END

IPDM E/R

Headlamp aiming motor

Continuity

Connector

Terminal

Connector

Terminal

RH

E101

56

E99

2

Existed

LH

E98