Nissan Qashqai J11. Manual - part 1375

P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OPER-

ATE

DLK-769

< SYMPTOM DIAGNOSIS >

[TYPE 5]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OP-
ERATE

Diagnosis Procedure

INFOID:0000000010683779

1.

CHECK “AUTO LOCK FUNCTION” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTO LOCK FUNCTION” in “WORK SUPPORT” mode.

3.

Check “AUTO LOCK FUNCTION” in “WORK SUPPORT”.
Refer to 

DLK-675, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Type 5)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set “MODE 2” in “AUTO LOCK FUNCTION”.

2.

CHECK “AUTO UNLOCK FUNCTION” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTO UNLOCK FUNCTION” in “WORK SUPPORT” mode.

3.

Check “AUTO UNLOCK FUNCTION” in “WORK SUPPORT”.
Refer to 

DLK-675, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Type 5)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “MODE 2” in “AUTO UNLOCK FUNCTION”.

3.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

DLK-770

< SYMPTOM DIAGNOSIS >

[TYPE 5]

P POSITION WARNING DOES NOT OPERATE

P POSITION WARNING DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000010672399

1.

CHECK DTC WITH BCM, TCM AND COMBINATION METER

Check that DTC is not detected with BCM, TCM and combination meter.
Is the inspection result normal?

YES

>> GO TO 2.

NO-1

>> Refer to 

BCS-89, "DTC Index"

. (BCM)

NO-2

>> Refer to 

MWI-40, "DTC Index"

. (Combination meter)

2.

CHECK COMBINATION METER BUZZER

Check combination meter buzzer.
Refer to 

DLK-83, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.
Refer to 

DLK-101, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK DOOR SWITCH

Check front door switch (driver side).
Refer to 

DLK-95, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK INSIDE KEY ANTENNA

Check inside key antenna.
• Console: Refer to 

DLK-71, "DTC Logic"

.

• Luggage room: Refer to 

DLK-74, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

CHECK INFORMATION DISPLAY

Check information display.
Refer to 

DLK-99, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace the malfunctioning parts.

7.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

REMINDER FUNCTION DOES NOT OPERATE

DLK-771

< SYMPTOM DIAGNOSIS >

[TYPE 5]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

REMINDER FUNCTION DOES NOT OPERATE

DOOR REQUEST SWITCH

DOOR REQUEST SWITCH : Description

INFOID:0000000010683773

Reminder function does not operate using door request switch.

DOOR REQUEST SWITCH : Diagnosis Procedure

INFOID:0000000010683774

1.

CHECK DTC WITH BCM AND COMBINATION METER

Check that DTC is not detected with BCM and combination meter.

Is the inspection result normal?

YES

>> GO TO 2.

NO-1

>> Refer to 

BCS-89, "DTC Index"

. (BCM)

NO-2

>> Refer to 

MWI-40, "DTC Index"

. (Combination meter)

2.

CHECK “ANSWER BACK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “ANSWER BACK” in “WORK SUPPORT” mode.

3.

Check the “ANSWER BACK” in “WORK SUPPORT”.
Refer to 

DLK-676, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “Off” in “ANSWER BACK”.

3.

CHECK “ANSWER BACK I-KEY LOCK UNLOCK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “ANSWER BACK I-KEY LOCK UNLOCK” in “WORK SUPPORT” mode.

3.

Check the “ANSWER BACK I-KEY LOCK UNLOCK” in “WORK SUPPORT”.
Refer to 

DLK-676, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Set “BUZZER”, “HORN” or “Off” in “ANSWER BACK I-KEY LOCK UNLOCK”.

4.

CHECK HAZARD FUNCTION

Check hazard function.
Refer to 

DLK-741, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.
Refer to 

DLK-744, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

CHECK HORN FUNCTION

Check horn function.
Refer to 

SEC-173, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace the malfunctioning parts.

7.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

DLK-772

< SYMPTOM DIAGNOSIS >

[TYPE 5]

REMINDER FUNCTION DOES NOT OPERATE

2.

Confirm the operation after replacement. 

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

INTELLIGENT KEY

INTELLIGENT KEY : Description

INFOID:0000000010683775

Reminder function does not operate using Intelligent Key.

INTELLIGENT KEY : Diagnosis Procedure

INFOID:0000000010683776

1.

CHECK DTC WITH BCM AND COMBINATION METER

Check that DTC is not detected with BCM and combination meter.

Is the inspection result normal?

YES

>> GO TO 2.

NO-1

>> Refer to 

BCS-89, "DTC Index"

. (BCM)

NO-2

>> Refer to 

MWI-40, "DTC Index"

. (Combination meter)

2.

CHECK “ANSWER BACK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “ANSWER BACK” in “WORK SUPPORT” mode.

3.

Check the “ANSWER BACK” in “WORK SUPPORT”.
Refer to 

DLK-676, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “Off” in “ANSWER BACK”.

3.

CHECK “ANSWER BACK KEYLESS LOCK UNLOCK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “ANSWER BACK KEYLESS LOCK UNLOCK” in “WORK SUPPORT” mode.

3.

Check the “ANSWER BACK KEYLESS LOCK UNLOCK” in “WORK SUPPORT”.
Refer to 

DLK-676, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Set “On” or “Off” in “ANSWER BACK KEYLESS LOCK UNLOCK”.

4.

CHECK HAZARD FUNCTION

Check hazard function.
Refer to 

DLK-741, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK HORN FUNCTION

Check horn function.
Refer to 

SEC-173, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

2.

Confirm the operation after replacement. 

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.