Nissan Qashqai J11. Manual - part 1363

 

  Index      Nissan     Nissan Qashqai J11 - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1361  1362  1363  1364   ..

 

 

Nissan Qashqai J11. Manual - part 1363

 

 

BACK DOOR OPENER SWITCH

DLK-721

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 5]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK BACK DOOR OPENER SWITCH

Refer to 

DLK-721, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace back door opener switch assembly.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000010672330

1.

CHECK BACK DOOR OPENER SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect back door opener switch assembly connector.

3.

Check continuity between back door opener switch assembly terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace back door opener switch assembly.

Back door opener switch assembly

Ground

Continuity 

Connector

Terminal

D94

4

Existed

Back door opener switch assembly

Condition

Continuity 

Terminal 

1

4

Back door opener 
switch

Pressed

Existed

Released

Not existed

DLK-722

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 5]

BACK DOOR REQUEST SWITCH

BACK DOOR REQUEST SWITCH

Component Function Check

INFOID:0000000010672331

1.

CHECK FUNCTION

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “REQ SW-BD/TR” in “DATA MONITOR” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Back door request switch is OK.

NO

>> Refer to 

DLK-722, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010672332

1.

CHECK BACK DOOR REQUEST SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect back door opener switch assembly connector.

3.

Check voltage between back door opener switch assembly harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK BACK DOOR REQUEST SWITCH CIRCUIT

1.

Disconnect BCM connector.

2.

Check continuity between BCM harness connector and back door opener switch assembly harness con-
nector.

3.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

NO

>> Repair harness or connector.

3.

CHECK BACK DOOR REQUEST SWITCH GROUND CIRCUIT

Check continuity between back door opener switch assembly harness connector and ground.

Monitor item

Condition

Status

REQ SW-BD/TR

Back door request switch

Pressed

On

Released

Off

(+)

(–)

Voltage

Back door opener switch assembly

Connector

Terminal 

D94

2

Ground

9 - 16 V

BCM

Back door opener switch assembly

Continuity 

Connector

Terminal

Connector

Terminal

B4

6

D94

2

Existed

BCM

Ground

Continuity 

Connector

Terminal

B4

6

Not existed

BACK DOOR REQUEST SWITCH

DLK-723

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 5]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK BACK DOOR REQUEST SWITCH

Refer to 

DLK-723, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace back door opener switch assembly.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000010672333

1.

CHECK BACK DOOR REQUEST SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect back door opener switch assembly connector.

3.

Check continuity between back door opener switch assembly terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace back door opener switch assembly.

Back door opener switch assembly

Ground

Continuity 

Connector

Terminal

D94

3

Existed

 Back door opener switch assembly

Condition

Continuity 

Terminal

2

3

Back door request switch

Pressed

Existed

Released

Not existed

DLK-724

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 5]

COMBINATION METER BUZZER

COMBINATION METER BUZZER

Component Function Check

INFOID:0000000010672334

1.

CHECK FUNCTION

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “INSIDE BUZZER” in “ACTIVE TEST” mode.

3.

Touch “Buzzer 1”, “Buzzer 2” or “Buzzer 3” to check that it works normally.

Is the inspection result normal?

Yes

>> Buzzer (combination meter) is OK.

No

>> Refer to 

DLK-724, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010672335

1.

CHECK METER BUZZER CIRCUIT

Refer to 

WCS-44, "Component Function Check"

.

Is the inspection result normal?

Yes

>> GO TO 2.

No

>> Repair or replace the malfunctioning parts.

2.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

 

 

 

 

 

 

 

Content   ..  1361  1362  1363  1364   ..