Content .. 201 202 203 204 ..

Nissan Juke (2014 year). Service Repair Manual - part 203

RF-20

< DTC/CIRCUIT DIAGNOSIS >

SUNROOF MOTOR ASSEMBLY

SUNROOF MOTOR ASSEMBLY

Component Function Check

INFOID:0000000009753727

CHECK SUNROOF MOTOR FUNCTION

Check tilt up/down & slide open/close operations with sunroof switch.
Is the inspection result normal?

YES

>> GO TO 2.

>> Check sunroof switch. Refer to

RF-21, "Diagnosis Procedure"

CHECK SUNROOF MOTOR ASSEMBLY INPUT SIGNAL

Start engine.

Drive the vehicle at more than 40 km/h (25 MPH).

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.

Check tilt up/down & slide open/close operations with sunroof switch.

Is the inspection result normal?

YES

>> INSPECTION END

>> Refer to

RF-20, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000009753728

SUNROOF MOTOR ASSEMBLY

CHECK SUNROOF MOTOR ASSEMBLY INPUT SIGNAL

Turn ignition switch OFF.

Disconnect combination meter harness connector and sunroof motor assembly harness connector.

Check continuity between combination meter harness connector and sunroof motor assembly harness
connector.

Check continuity between sunroof motor assembly harness connector and ground.

Is the inspection result normal?

YES

>> Check combination meter. Refer to

MWI-50, "COMBINATION METER : Diagnosis Procedure"

>> Repair or replace harness or connector.

Combination meter

Sunroof motor assembly

Continuity

Connector

Terminal

Connector

Terminal

M34

R11

Exists

Sunroof motor assembly

Ground

Continuity

Connector

Terminal

R11

Not existed

Revision: 2013 October

2014 JUKE

SUNROOF SWITCH

RF-21

< DTC/CIRCUIT DIAGNOSIS >

SUNROOF SWITCH

Component Function Check

INFOID:0000000009753729

CHECK SUNROOF MOTOR FUNCTION

Check tilt up/down & slide open/close operations with sunroof switch.
Is the inspection result normal?

YES

>> INSPECTION END

>> Refer to

RF-21, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000009753730

PERFORM INITIALIZATION PROCEDURE

Initialization procedure is executed and operation is confirmed. Refer to

RF-17, "ADDITIONAL SERVICE

WHEN REPLACING CONTROL UNIT : Special Repair Requirement"

Check tilt up/down & slide open/close operations with sunroof switch.

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 2.

CHECK SUNROOF SWITCH GROUND CIRCUIT

Turn ignition switch OFF.

Disconnect sunroof switch harness connector.

Check continuity between sunroof switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace harness or connector.

CHECK SUNROOF SWITCH INPUT SIGNAL

Turn ignition switch ON.

Check voltage between sunroof switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

>> GO TO 4.

CHECK SUNROOF SWITCH CIRCUIT

Turn ignition switch OFF.

Disconnect sunroof motor assembly harness connector.

Check continuity between sunroof motor assembly harness connector and sunroof switch harness con-
nector.

Sunroof switch

Ground

Continuity

Connector

Terminal

Existed

(+)

(

−

)

Voltage (V)

(Approx.)

sunroof switch

Connector

Terminal

Ground

Battery Voltage

Revision: 2013 October

2014 JUKE

RF-22

< DTC/CIRCUIT DIAGNOSIS >

SUNROOF SWITCH

Check continuity between sunroof motor assembly harness connector and ground.

Is the inspection result normal?

YES

>> Replace sunroof motor assembly. Refer to

RF-37, "Removal and Installation"

>> Repair or replace harness or connector.

CHECK SUNROOF SWITCH

Check sunroof switch.
Refer to

RF-22, "Component Inspection"

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-46, "Intermittent Incident"

>> Replace sunroof switch (built in map lamp assembly). Refer to

RF-45, "Removal and Installation"

Component Inspection

INFOID:0000000009753731

SUNROOF SWITCH

CHECK SUNROOF SWITCH

Turn ignition switch OFF.

Disconnect sunroof switch harness connector.

Check continuity sunroof switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

>> Replace sunroof switch. Refer to

RF-45, "Removal and Installation"

Sunroof motor assembly

Sunroof switch

Continuity

Connector

Terminal

Connector

Terminal

R11

Existed

Sunroof motor assembly

Ground

Continuity

Connector

Terminal

R11

Not existed

Terminals

Condition

Continuity

Sunroof switch is operated

TILT DOWN or SLIDE OPEN

Existed

Other than above

Not existed

Sunroof switch is operated

TILT UP or SLIDE CLOSE

Existed

Other than above

Not existed

Revision: 2013 October

2014 JUKE

SUNROOF DOES NOT OPERATE PROPERLY

RF-23

< SYMPTOM DIAGNOSIS >

SYMPTOM DIAGNOSIS

SUNROOF DOES NOT OPERATE PROPERLY

Description

INFOID:0000000009753732

Sunroof does not operate normally.
• Glass lid does not slide or tilt.
• Judder occurs during sliding operation of glass lid.
• Sliding or tilting operation of glass lid is slow.

Diagnosis Procedure

INFOID:0000000009753733

CHECK GLASS LID

Check the following items.
• Cracks, damage, or deformation of weather-strip.
• Sticking of weather-strip.
• Loose or missing glass lid mounting blot.
• Misalignment of glass lid.

Refer to

RF-34, "Removal and Installation"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CHECK SUNROOF FRAME ASSEMBLY

Check the following items.
• Damage, deformation or trapped foreign material of slide rail.
• Insufficient application of grease to sliding section of slide rail.

Refer to

RF-40, "Removal and Installation"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

CHECK SUNSHADE

Check sunshade for damage, deformation, of interference with other parts.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

CHECK BCM POWER SUPPLY AND GROUND CIRCUIT

Check BCM power supply and ground circuit.
Refer to

BCS-83, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

CHECK SUNROOF MOTOR ASSEMBLY POWER SUPPLY AND GROUND CIRCUIT

Check sunroof motor assembly power supply and ground circuit.
Refer to

RF-20, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 6.

>> Repair or replace the malfunctioning parts.

CHECK SUNROOF SWITCH

Check sunroof switch.
Refer to

RF-21, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 7.

Revision: 2013 October

2014 JUKE

RF-24

< SYMPTOM DIAGNOSIS >

SUNROOF DOES NOT OPERATE PROPERLY

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-46, "Intermittent Incident"

>> GO TO 1.

Revision: 2013 October

2014 JUKE

AUTO OPERATION DOES NOT OPERATE

RF-25

< SYMPTOM DIAGNOSIS >

AUTO OPERATION DOES NOT OPERATE

Description

INFOID:0000000009753734

Auto operation does not operate
• Auto operation of glass lid does not operate.
• Glass lid stops halfway.
• Anti-pinch function operates.

Diagnosis Procedure

INFOID:0000000009753735

CHECK GLASS LID

Check the following items.
• Cracks, damage, or deformation of weather-strip.
• Sticking of weather-strip.
• Loose or missing glass lid mounting blot.
• Misalignment of glass lid.

Refer to

RF-34, "Removal and Installation"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CHECK WIND DEFLECTOR

Check wind deflector for deformation and interference.
Refer to

RF-44, "Removal and Installation"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

CHECK SUNROOF FRAME ASSEMBLY

Check the following items.
• Damage, deformation or trapped foreign material of slide rail.
• Insufficient application of grease to sliding section of slide rail.

Refer to

RF-40, "Removal and Installation"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.
Refer to

RF-17, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-

ment"

Is the inspection result normal?

YES

>> INSPECTION END

>> Replace sunroof motor assembly. Refer to

RF-37, "Removal and Installation"

Revision: 2013 October

2014 JUKE

RF-26

< SYMPTOM DIAGNOSIS >

SUNROOF DOES NOT OPERATE ANTI-PINCH FUNCTION

SUNROOF DOES NOT OPERATE ANTI-PINCH FUNCTION

Diagnosis Procedure

INFOID:0000000009753736

PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.
Refer to

RF-17, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-

ment"

Is the inspection result normal?

YES

>> Inspection end.

>> Check intermittent incident. Refer to

GI-46, "Intermittent Incident"

Revision: 2013 October

2014 JUKE

RETAINED POWER OPERATION DOES NOT OPERATE PROPERLY

RF-27

< SYMPTOM DIAGNOSIS >

RETAINED POWER OPERATION DOES NOT OPERATE PROPERLY

Diagnosis Procedure

INFOID:0000000009753737

CHECK DOOR SWITCH

Check door switch.
Refer to

DLK-81, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CHECK SUNROOF MOTOR ASSEMBLY POWER SUPPLY AND GROUND

Check sunroof motor assembly power supply and ground circuit.
Refer to

RF-20, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

REPLACE BCM

• Replace BCM. Refer to

BCS-90, "Removal and Installation"

(with Intelligent Key) or

BCS-157, "Removal and

Installation"

(without Intelligent Key).

• Confirm the operation after replacement.
Is the result normal?

YES

>> INSPECTION END

>> Check intermittent incident. Refer to

GI-46, "Intermittent Incident"

Revision: 2013 October

2014 JUKE

RF-28

< SYMPTOM DIAGNOSIS >

SQUEAK AND RATTLE TROUBLE DIAGNOSES

SQUEAK AND RATTLE TROUBLE DIAGNOSES

Work Flow

INFOID:0000000009753738

CUSTOMER INTERVIEW

Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer comments. Refer to

RF-32, "Diagnostic Worksheet"

. This information is necessary to duplicate the

conditions that exist when the noise occurs.
• The customer may not be able to provide a detailed description or the location of the noise. Attempt to obtain

all the facts and conditions that exist when the noise occurs (or does not occur).

• If there is more than one noise in the vehicle, perform a diagnosis and repair the noise that the customer is

concerned about. This can be accomplished by performing a test drive with the customer.

• After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics

are provided so that the customer, service adviser, and technician use the same language when describing
the noise.

• Squeak – (Like tennis shoes on a clean floor)

Squeak characteristics include the light contact / fast movement / brought on by road conditions / hard sur-
faces = high-pitched noise / softer surfaces = low-pitched noises / edge to surface = chirping

• Creak – (Like walking on an old wooden floor)

Creak characteristics include firm contact / slow movement/twisting with a rotational movement / pitch
dependent on materials / often brought on by activity.

• Rattle – (Like shaking a baby rattle)

Rattle characteristics include fast repeated contact / vibration or similar movement / loose parts/missing clip
or fastener / incorrect clearance.

• Knock – (Like a knock on a door)

Knock characteristics include hollow sounds / sometimes repeating / often brought on by driver action.

• Tick – (Like a clock second hand)

Tick characteristics include gentle contacting of light materials / loose components / can be caused by driver
action or road conditions.

• Thump – (Heavy, muffled knock noise)

Thump characteristics include softer knock / dull sounds often brought on by activity.

• Buzz – (Like a bumblebee)

Buzz characteristics include high frequency rattle / firm contact.

• Often the degree of acceptable noise level varies depending upon the person. A noise that a technician may

judge as acceptable may be very irritating to a customer.

• Weather conditions, especially humidity and temperature, may have a great effect on noise level.

DUPLICATE THE NOISE AND TEST DRIVE

If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when the repair is reconfirmed.

SBT842

Revision: 2013 October

2014 JUKE

SQUEAK AND RATTLE TROUBLE DIAGNOSES

RF-29

< SYMPTOM DIAGNOSIS >

If the noise can be duplicated easily during the test drive, to help identify the source of the noise, try to dupli-
cate the noise with the vehicle stopped by doing one or all of the following items:
1) Close a door.
2) Tap or push/pull around the area where the noise appears to be coming from.
3) Rev the engine.
4) Use a floor jack to recreate vehicle “twist”.
5) At idle, apply engine load (electrical load, half-clutch on M/T models, drive position on A/T models).
6) Raise the vehicle on a hoist and hit a tire with a rubber hammer.
• Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs.
• If it is difficult to duplicate the noise, drive the vehicle slowly on an undulating or rough road to stress the

vehicle body.

CHECK RELATED SERVICE BULLETINS

After verifying the customer concern or symptom, check ASIST for Technical Service Bulletins (TSBs) related
to the concern or symptom.
If a TSB relates to the symptom, follow the procedure to repair the noise.

LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE

Narrow down the noise to a general area. To help pinpoint the source of the noise, use a listening tool
(Chassis ear: J-39570, engine ear, and mechanics stethoscope).

Narrow down the noise to a more specific area and identify the cause of the noise by:

• Removing the component(s) in the area that is / are suspected to be the cause of the noise.

Do not use too much force when removing clips and fasteners, otherwise clips and fasteners can be broken
or lost during the repair, resulting in the creation of new noise.

• Tapping or pushing/pulling the component(s) that is / are suspected to be the cause of the noise.

Do not tap or push/pull the component(s) with excessive force, otherwise the noise is eliminated only tempo-
rarily.

• Feeling for a vibration by hand by touching the component(s) that is / are suspected to be the cause of the

noise.

• Placing a piece of paper between components that are suspected to be the cause of the noise.
• Looking for loose components and contact marks.

Refer to

RF-30, "Inspection Procedure"

REPAIR THE CAUSE

• If the cause is a loose component, tighten the component securely.
• If the cause is insufficient clearance between components:
- Separate components by repositioning or loosening and retightening the components, if possible.
- Insulate components with a suitable insulator such as urethane pads, foam blocks, felt cloth tape, or ure-

thane tape. A NISSAN Squeak and Rattle Kit (J-50397) is available through the authorized NISSAN Parts
Department.

CAUTION:

Never use excessive force as many components are constructed of plastic and may be damaged.
NOTE:
Always check with the Parts Department for the latest parts information.
The following materials are contained in the NISSAN Squeak and Rattle Kit (J-50397) are listed on the inside
cover of the kit; and can each be ordered separately as needed.
URETHANE PADS [1.5 mm (0.059 in) thick]
Insulates connectors, harness, etc.
• 76268-9E005: 100

135 mm (3.937

5.315 in)

• 76884-71L01: 60

85 mm (2.362

3.346 in)

• 76884-71L02: 15

25 mm (0.591

0.984 in)

INSULATOR (Foam blocks)
Insulates components from contact. Can be used to fill space behind a panel.
• 73982-9E000: 45 mm (1.772 in) thick, 50

50 mm (1.969

1.969 in)

• 73982-50Y00: 10 mm (0.394 in) thick, 50

50 mm (1.969

1.969 in)

INSULATOR (Light foam block)
80845-71L00: 30 mm (1.181 in) thick, 30

50 mm (1.181

1.969in)

FELT CLOTHTAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
• 68370-4B000: 15

25 mm (0.591

0.984 in) pad

• 68239-13E00: 5 mm (0.197 in) wide tape roll

Revision: 2013 October

2014 JUKE

RF-30

< SYMPTOM DIAGNOSIS >

SQUEAK AND RATTLE TROUBLE DIAGNOSES

The following materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in place of UHMW tape that is visible or does not fit. Only lasts a few months.
SILICONE SPRAY
Used when grease cannot be applied.
DUCT TAPE
Used to eliminate movement.

CONFIRM THE REPAIR

After repair is complete, test drive the vehicle to confirm that the cause of noise is repaired by test driving the
vehicle. Operate the vehicle under the same conditions as when the noise originally occurred. Refer to the
notes on the Diagnostic Worksheet.

Inspection Procedure

INFOID:0000000009753739

Refer to Table of Contents for specific component removal and installation information.

INSTRUMENT PANEL

Most incidents are caused by contact and movement between:

The cluster lid A and instrument panel

Acrylic lens and combination meter housing

Instrument panel to front pillar garnish

Instrument panel to windshield

Instrument panel mounting pins

Wiring harnesses behind the combination meter

A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by
applying felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate
wiring harness.

CAUTION:

Never use silicone spray to isolate a squeak or rattle. If the area is saturated with silicone, the
recheck of repair becomes impossible.

CENTER CONSOLE

Components to check include:

Shifter assembly cover to finisher

A/C control unit and cluster lid C

Wiring harnesses behind audio and A/C control unit

The instrument panel repair and isolation procedures also apply to the center console.

DOORS

Check the following items:

Finisher and inner panel making a slapping noise

Inside handle escutcheon connection to door finisher

Wiring harnesses tapping

Door striker out of alignment causing a popping noise on starts and stops

Tapping, moving the components, or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. The areas can usually be insulated with felt cloth tape or insulator foam blocks from
the NISSAN Squeak and Rattle Kit (J-50397) to repair the noise.

TRUNK

Trunk noises are often caused by a loose jack or loose items put into the trunk by the customer.
In addition check for the following items:
1.

Trunk lid dumpers out of adjustment

Trunk lid striker out of adjustment

Revision: 2013 October

2014 JUKE

SQUEAK AND RATTLE TROUBLE DIAGNOSES

RF-31

< SYMPTOM DIAGNOSIS >

Trunk lid torsion bars knocking together

A loose license plate or bracket

Most of these incidents can be repaired by adjusting, securing, or insulating the item(s) or component(s) caus-
ing the noise.

SUNROOF/HEADLINING

Noises in the sunroof / headlining area can often be traced to one of the following items:

Sunroof lid, rail, linkage, or seals making a rattle or light knocking noise

Sunvisor shaft shaking in the holder

Front or rear windshield touching headlining and squeaking

Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.

SEATS

When isolating seat noise it is important to note the position the seat is in and the load placed on the seat
when the noise occurs. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Causes of seat noise include:

Headrest rods and holder

A squeak between the seat pad cushion and frame

The rear seatback lock and bracket

These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.

UNDERHOOD

Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:

Any component mounted to the engine wall

Components that pass through the engine wall

Engine wall mounts and connectors

Loose radiator mounting pins

Hood bumpers out of adjustment

Hood striker out of adjustment

These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move, or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.

Revision: 2013 October

2014 JUKE

RF-32

< SYMPTOM DIAGNOSIS >

SQUEAK AND RATTLE TROUBLE DIAGNOSES

Diagnostic Worksheet

INFOID:0000000009753740

PIIB8740E

Revision: 2013 October

2014 JUKE

SQUEAK AND RATTLE TROUBLE DIAGNOSES

RF-33

< SYMPTOM DIAGNOSIS >

PIIB8742E

Revision: 2013 October

2014 JUKE

RF-34

< REMOVAL AND INSTALLATION >

GLASS LID

REMOVAL AND INSTALLATION

GLASS LID

Exploded View

INFOID:0000000009753741

Removal and Installation

INFOID:0000000009753742

REMOVAL

CAUTION:

• Always work with a helper.

TORX bolt

Glass lid

Sunroof bracket

Drain hose (front)

Drain connector (front)

Sunroof welt

Sunroof motor assembly

Drain hose (rear)

Drain connector (rear)

10. Sunroof unit assembly

11.

Seal guide rubber

12. Seal sunroof

: Indicates that the part is connected at points with same symbol in actual vehicle.

JSKIA2884ZZ

Revision: 2013 October

2014 JUKE

GLASS LID

RF-35

< REMOVAL AND INSTALLATION >

• Fully close the glass lid, before removal, then never operate sunroof motor after removal.

Remove glass lid mounting TORX bolts (A).

Remove glass lid from vehicle.

INSTALLAITON

Note the following items, and then install in the reverse order of removal.

CAUTION:

After installing the glass lid, perform the leak test and check the there is no malfunction.
NOTE:
After installation carry out fitting adjustment. Refer to

RF-35, "Adjustment"

Adjustment

INFOID:0000000009753743

If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.

Loosen glass lid mounting TORX bolts.

Adjust the clearance of glass lid and roof panel according to the fitting standard dimension.

To prevent glass lid from moving after adjustment, first tighten the TORX bolts of front left, and then
tighten the TORX bolts of rear right.

Tilt glass lid up and down several times to check that it moves smoothly.

NOTE:

JMKIA0029ZZ

JMKIA5137ZZ

Roof panel

Glass lid

Portion

a (Clearance)

b (Surface height difference)

−

0.6

−

2.2 mm (0.024

−

0.087 in)

(

−

0.7)

−

(+2.3) mm [(

−

0.028)

−

(+0.091) in]

−

0.6

−

2.2 mm (0.024

−

0.087 in)

(

−

0.7)

−

(+2.3) mm [(

−

0.028)

−

(+0.091) in]

−

0.6

−

2.2 mm (0.024

−

0.087 in)

(

−

0.7)

−

(+2.3) mm [(

−

0.028)

−

(+0.091) in]

Revision: 2013 October

2014 JUKE

Content .. 201 202 203 204 ..