Nissan Juke (2014 year). Service Repair Manual

BCS-102

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

DIAGNOSIS SYSTEM (BCM)

COMMON ITEM

COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000009751652

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

: Applicable item

DOOR LOCK

DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)

INFOID:0000000010286784

WORK SUPPORT

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

Rear window defogger

REAR DEFOGGER

Warning chime

BUZZER

Interior room lamp control

INT LAMP

Remote keyless entry system

MULTI REMOTE ENT

Exterior lamp

HEAD LAMP

Wiper and washer

WIPER

Turn signal and hazard warning lamps

FLASHER

Air conditioning system

AIR CONDITONER

Combination switch

COMB SW

Body control system

BCM

NATS

IMMU

Interior room lamp battery saver

BATTERY SAVER

Back door open

TRUNK

Theft warning alarm

THEFT ALM

RAP system

RETAINED PWR

Signal buffer system

SIGNAL BUFFER

Panic alarm

PANIC ALARM

TPMS

AIR PRESSUE MONITOR

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-103

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

*: P range interlock door lock/unlock can be selected for M/T models, but automatic door lock/unlock function does not operate.

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST

Monitor item

Description

DOOR LOCK-UNLOCK SET

Anti-hijack function can be changed to operate with this mode
• On: Operate
• Off: Non-operation

AUTOMATIC DOOR LOCK SE-
LECT

Automatic door lock function can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 24km/h (15MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other

than the P position

AUTOMATIC DOOR UNLOCK
SELECT

Automatic door unlock function can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to

OFF

• MODE 2*: All doors are unlocked when shifting the selector lever from any position other

than the P to P position

• MODE 3: Driver side door is unlocked when the power supply position is changed from ON

to OFF

• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position

other than the P to P position

• MODE 5: Driver side door is unlocked when key out of key switch
• MODE 6: All doors are unlocked when key out of key switch

AUTOMATIC LOCK/UNLOCK
SET

Automatic door lock/unlock function can be selected from the following in this mode
• Off: Non-operation
• Unlock Only: Door unlock operation only
• Lock Only: Door lock operation only
• Lock/Unlock: Door lock and unlock operation

Monitor Item

Contents

IGN ON SW

Indicated [On/Off] condition of ignition switch in ON position

KEY ON SW

Indicated [On/Off] condition of key switch

CDL LOCK SW

Indicated [On/Off] condition of lock signal from door lock unlock switch

CDL UNLOCK SW

Indicated [On/Off] condition of unlock signal from door lock unlock switch

DOOR SW-DR

Indicated [On/Off] condition of front door switch (driver side)

DOOR SW-AS

Indicated [On/Off] condition of front door switch (passenger side)

DOOR SW-RR

Indicated [On/Off] condition of rear door switch RH

DOOR SW-RL

Indicated [On/Off] condition of rear door switch LH

BACK DOOR SW

Indicated [On/Off] condition of back door switch

LOCK STATUS

Indicated [On/Off] condition of front door driver side

ACC ON SW

Indicated [On/Off] condition of ignition switch in ACC position

KEYLESS LOCK

Indicated [On/Off] condition of lock signal from key fob

KEYLESS UNLOCK

Indicated [On/Off] condition of unlock signal from key fob

KEY CYL LK-SW

Indicated [On/Off] condition of lock signal from door key cylinder

KEY CYL UN-SW

Indicated [On/Off] condition of unlock signal from door key cylinder

VEHICLE SPEED

Display the vehicle speed signal received from combination meter by numer-
ical value [Km/h]

Revision: 2013 October

2014 JUKE

BCS-104

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

REAR WINDOW DEFOGGER

REAR WINDOW DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER)

INFOID:0000000010286826

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST

BUZZER

BUZZER : CONSULT Function (BCM - BUZZER)

INFOID:0000000010286828

CONSULT APPLICATION ITEMS

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Test item

Description

DOOR LOCK

This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LCK” on CONSULT screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT screen is

touched

• The back door lock actuator is unlocked when “BD ULK” on CONSULT screen is touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT screen is

touched

Monitor Item

Description

REAR DEF SW

Displays “Press (ON)/other (OFF)” status determined with the rear window defogger switch.

IGN ON SW

Indicates [ON/OFF] condition of ignition switch in ON position.

ACC ON SW

Indicates [ON/OFF] condition of ignition switch ACC position.

Test Item

Description

REAR DEFOGGER

Rear window defogger operates when “ON” on CONSULT screen is touched.

Test item

Diagnosis mode

Description

BUZZER

Data Monitor

Displays BCM input data in real time.

Active Test

Operation of electrical loads can be checked by sending driving signal to them.

Display item

[Unit]

Description

IGN ON SW
[On/Off]

Status of ignition switch judged by BCM.

KEY ON SW
[On/Off]

Status of key switch judged by BCM.

DOOR SW-DR
[km/h]

Status of driver side door switch judged by BCM.

REVERSE SW CAN
[On/Off]

This item is displayed, but cannot be monitored.

TAIL LAMP SW
[On/Off]

Status of lighting switch judged by BCM using the combination switch readout function.

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-105

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

ACTIVE TEST

INT LAMP

INT LAMP : CONSULT Function (BCM - INT LAMP)

INFOID:0000000010286821

WORK SUPPORT

FR FOG SW
[On/Off]

Status of front fog lamp switch judged by BCM using the combination switch readout function.

BUCKLE SW
[On/Off]

Status of seat belt buckle switch (driver side) received from combination meter with CAN communica-
tion line.

VEHICLE SPEED
[km/h]

Value of vehicle speed signal received from combination meter with CAN communication line.

Display item

[Unit]

Description

Display item

[Unit]

Description

SEAT BELT WARN TEST

The seat belt warning chime operation can be checked by operating the relevant function (On/Off).

IGN KEY WARN ALM

The key warning chime operation can be checked by operating the relevant function (On/Off).

LIGHT WARN ALM

The light warning chime operation can be checked by operating the relevant function (On/Off).

JPLIA0093GB

Service item

Setting item

Setting

ROOM LAMP TIMER SET

MODE 1

0 sec.

Sets the interior room lamp ON time. (Timer operating time)

MODE 2

7.5 sec.

MODE 3*

15 sec.

MODE 4

30 sec.

SET I/L D-UNLCK INTCON

On*

With the interior room lamp timer function

Off

Without the interior room lamp timer function

ROOM LAMP ON TIME SET

MODE 1

0.5 sec.

Sets the interior room lamp gradual brightening time.

MODE 2*

1 sec.

MODE 3

2 sec.

MODE 4

3 sec.

MODE 5

4 sec.

MODE 6

5 sec.

MODE 7

0 sec.

Revision: 2013 October

2014 JUKE

BCS-106

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

*: Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST

ROOM LAMP OFF TIME SET

MODE 1

0.5 sec.

Sets the interior room lamp gradual dimming time.

MODE 2*

1 sec.

MODE 3

2 sec.

MODE 4

3 sec.

MODE 5

4 sec.

MODE 6

5 sec.

MODE 7

0 sec.

R LAMP TIMER LOGIC SET

MODE 1*

Interior room lamp timer activates with synchronizing all doors.

MODE 2

Interior room lamp timer activates with synchronizing the driver door
only.

Service item

Setting item

Setting

Monitor item

[Unit]

Description

IGN ON SW
[On/Off]

Indicated [On/Off] condition of ignition switch in ON position

KEY ON SW
[On/Off]

Indicated [On/Off] condition of key switch

DOOR SW-DR
[On/Off]

Indicated [On/Off] condition of front door switch (driver side)

DOOR SW-AS
[On/Off]

Indicated [On/Off] condition of front door switch (passenger side)

DOOR SW-RR
[On/Off]

Indicated [On/Off] condition of rear door switch RH

DOOR SW- RL
[On/Off]

Indicated [On/Off] condition of rear door switch LH

BACK DOOR SW
[On/Off]

Indicated [On/Off] condition of back door switch

LOCK STATUS
[On/Off]

The switch status input from door lock status switch (driver side)

CDL LOCK SW
[On/Off]

Indicates [On/Off] condition of door lock and unlock switch

CDL UNLOCK SW
[On/Off]

Indicates [On/Off] condition of door lock and unlock switch

KEYLESS LOCK
[On/Off]

Indicates [On/Off] condition of lock signal from keyfob

KEYLESS UNLOCK
[On/Off]

Indicates [On/Off] condition of unlock signal from keyfob

TRNK/HAT MNTR
[On/Off]

NOTE:
This item is displayed, but cannot be tested

KEY CYL LK-SW
[On/Off]

Indicated [On/Off] condition of lock signal from door key cylinder

KEY CYL UN-SW
[On/Off]

Indicated [On/Off] condition of unlock signal from door key cylinder

ACC ON SW
[On/Off]

Indicates [On/Off] condition of ignition switch in ACC position

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-107

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

MULTI REMOTE ENT

MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT)

INFOID:0000000010286785

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST

WORK SUPPORT

Test item

Operation

Description

INT LAMP

Outputs the interior room lamp control signal.

Off

Stops the interior room lamp control signal.

Monitor Item

Condition

IGN ON SW

Indicates [On/Off] condition of ignition switch in ON position

KEY ON SW

Indicates [On/Off] condition of key switch

ACC ON SW

Indicates [On/Off] condition of ignition switch in ACC position

KEYLESS LOCK

Indicates [On/Off] condition of lock signal from keyfob

KEYLESS UNLOCK

Indicates [On/Off] condition of unlock signal from keyfob

KYLS TRNK/HAT

NOTE:
This item is displayed, but cannot be tested

DOOR SW-DR

Indicates [On/Off] condition of front door switch (driver side)

DOOR SW-AS

Indicates [On/Off] condition of front door switch (passenger side)

DOOR SW-RR

Indicates [On/Off] condition of rear door switch RH

DOOR SW-RL

Indicates [On/Off] condition of rear door switch LH

BACK DOOR SW

Indicates [On/Off] condition of back door switch

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be tested

CDL LOCK SW

Indicates [On/Off] condition of door lock and unlock switch

CDL UNLOCK SW

Indicates [On/Off] condition of door lock and unlock switch

KEYLESS PANIC

Indicates [On/Off] condition of PANIC button of keyfob

Test item

Description

INT LAMP

This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation

FLASHER

This test is able to check flasher operation [LH/RH/Off]

HORN

This test is able to check horn operation
• On: Operate

Test item

Description

REMO CONT IN REGIST

Keyfob ID code can be registered

REMO CONT IN ERASUR

Keyfob ID code can be erased

REMO CONT IN CONFIR

It can be checked whether Intelligent Key ID code is registered or not in this mode

HORN CHIRP SET

Hazard and horn reminder function (horn operation) mode can be changed in this mode
• On: Operate
• Off: Non-operation

Revision: 2013 October

2014 JUKE

BCS-108

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

HEADLAMP

HEADLAMP : CONSULT Function (BCM - HEAD LAMP)

INFOID:0000000010286817

WORK SUPPORT

*: Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

HAZARD LAMP SET

Hazard and horn reminder function (hazard operation) mode can be changed in this mode
• MODE1: Non-operation
• MODE2: Unlock operation only
• MODE3: Lock operation only
• MODE4: Lock and unlock operation

AUTO LOCK SET

Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute

PANIC ALARM SET

Panic alarm button pressing time on keyfob remote control button can be selected from the
following with this mode
• MODE1: 0.5 sec
• MODE2: Non-operation
• MODE3: 1.5 sec

TRUNK OPEN SET

NOTE:
This item is displayed, but cannot be tested

Test item

Description

Service item

Setting item

Setting

BATTERY SAVER SET

On*

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

ILL DELAY SET

MODE 1

NOTE:
This item is displayed but is not operated

MODE 2

MODE 3

MODE 4

MODE 5

MODE 6

MODE 7

MODE 8

HEAD LIGHT TIMER

MODE 1

10 sec.

Sets follow me home function activating time

MODE 2

30 sec.

AUTO LIGHT LOGIC SET

MODE 1

NOTE:
This item is displayed but is not operated

MODE 2

MODE 3

MODE 4

MODE 5

MODE 6

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-109

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

*: For models without front fog lamp, this item is displayed but is not monitored.

ACTIVE TEST

Monitor item

[Unit]

Description

IGN ON SW
[On/Off]

Indicated [On/Off] condition of ignition switch in ON position

ACC ON SW
[On/Off]

Indicates [On/Off] condition of ignition switch in ACC position

VEHICLE SPEED
[km/h]

Display the vehicle speed signal received from combination meter by numerical value
[Km/h]

HI BEAM SW
[On/Off]

Each switch status that BCM judges from the combination switch reading function

HEAD LAMP SW1
[On/Off]

HEAD LAMP SW2
[On/Off]

PASSING SW
[On/Off]

FR FOG SW*
[On/Off]

AUTO LIGHT SW
[On/Off]

NOTE:
This item is indicated, but can not monitored

DOOR SW-DR
[On/Off]

The switch status input from front door switch (driver side)

DOOR SW-AS
[On/Off]

The switch status input from front door switch (passenger side)

DOOR SW-RR
[On/Off]

The switch status input from rear door switch RH

DOOR SW- RL
[On/Off]

The switch status input from rear door switch LH

BACK DOOR SW
[On/Off]

The switch status input from back door switch

TURN SIGNAL R
[On/Off]

Each switch status that BCM judges from the combination switch reading function

TURN SIGNAL L
[On/Off]

TAIL LAMP SW
[On/Off]

KEY ON SW
[On/Off]

Indicated [On/Off] condition of key switch

KEYLESS LOCK
[On/Off]

Indicated [On/Off] condition of lock signal from key fob

PKB SW
[On/Off]

The parking brake switch status received from combination meter with CAN commu-
nication

ENGINE RUN
[On/Off]

The engine status received from ECM with CAN communication

OPTI SEN (DTCT)
[V]

NOTE:
This item is indicated, but can not monitored

OPTI SEN (FILT)
[V]

NOTE:
This item is indicated, but can not monitored

LIG SEN COND
[On/Off/NG]

NOTE:
This item is indicated, but can not monitored

Revision: 2013 October

2014 JUKE

BCS-110

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

: For models without front fog lamp, this item is displayed but is not tested.

: For models without daytime running light system, this item is not displayed.

WIPER

WIPER : CONSULT Function (BCM - WIPER)

INFOID:0000000010286824

WORK SUPPORT

*: Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Test item

Operation

Description

TAIL LAMP

Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON

Off

Stops the tail lamp request signal transmission

HEAD LAMP

Transmits the high beam request signal with CAN communication to turn
the headlamp (HI)

Transmits the low beam request signal with CAN communication to turn
the headlamp (LO)

Off

Stops the high & low beam request signal transmission

FR FOG LAMP*

Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON

Off

Stops the front fog lights request signal transmission

DAYTIME RUNNING LIGHT*

Transmits the daytime running light request signal via CAN communica-
tion to IPDM E/R

Off

Stop the daytime running light request signal transmission

ILL DIM SIGNAL

NOTE:
This item is indicated, but can not tested

Off

Service item

Setting item

Description

WIPER SPEED
SETTING

With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)

Off*

Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)

Monitor Item

[Unit]

Description

IGN ON SW
[On/Off]

Ignition switch ON status judged from ignition power supply.

IGN SW CAN
[On/Off]

Ignition switch ON status received from IPDM E/R with CAN communication.

FR WIPER HI
[On/Off]

Each switch status that BCM judges from the combination switch reading function.

FR WIPER LOW
[On/Off]

FR WIPER INT
[On/Off]

FR WASHER SW
[On/Off]

INT VOLUME
[1

−

Each switch status that BCM judges from the combination switch reading function.

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-111

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

ACTIVE TEST

FLASHER

FLASHER : CONSULT Function (BCM - FLASHER)

INFOID:0000000010286818

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST

FR WIPER STOP
[On/Off]

Front wiper motor (stop position) status received from IPDM E/R with CAN communication.

VEHICLE SPEED
[km/h]

The value of the vehicle speed signal received from combination meter with CAN communication.

RR WIPER ON
[On/Off]

Each switch status that BCM judges from the combination switch reading function.

RR WIPER INT
[On/Off]

RR WASHER SW
[On/Off]

RR WIPER STOP
[On/Off]

Rear wiper motor (stop position) status input from the rear wiper motor.

REVERSE SW CAN
[On/Off]

Reverse position status as judged from TCM with CAN communication.

RAIN SENSOR
[Off/LOW/HIGH/SPLASH/NG]

NOTE:
This item is displayed, but cannot be monitored.

Monitor Item

[Unit]

Description

Test item

Operation

Description

FR WIPER

Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to
operate the front wiper HI operation.

Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.

INT

Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.

Off

Stops transmitting the front wiper request signal to stop the front wiper operation.

RR WIPER

Outputs the voltage to operate the rear wiper motor.

Off

Stops the voltage to stop.

Monitor item

[Unit]

Description

IGN ON SW
[On/Off]

Indicates [On/Off] condition of ignition switch in ON position

TURN SIGNAL R
[On/Off]

Each switch status that BCM detects from the combination switch reading function

TURN SIGNAL L
[On/Off]

HAZARD SW
[On/Off]

The switch status input from the hazard switch

Revision: 2013 October

2014 JUKE

BCS-112

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

AIR CONDITIONER

AIR CONDITIONER : CONSULT Function (BCM - AIR CONDITIONER) (Manual A/C)

INFOID:0000000010286780

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Display item list

ACTIVE TEST

COMB SW

COMB SW : CONSULT Function (BCM - COMB SW)

INFOID:0000000009751662

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Test item

Operation

Description

FLASHER

Outputs the voltage to turn the right side turn signal lamps ON.

Outputs the voltage to turn the left side turn signal lamps ON.

Off

Stops the voltage to turn the turn signal lamps OFF.

Monitor Item [Unit]

Contents

FAN ON SIG

[On/Off]

Displays blower motor status as judged from blower fan ON signal.

AIR COND SW

[On/Off]

Displays A/C switch status as judged from A/C switch signal.

THERMO AMP

[On/Off]

Displays thermo control amp. status as judged from thermo control amp. signal.

IGN SW

[On/Off]

Displays ignition switch position status as judged form ignition switch signal.

FR DEF SW

[On/Off]

Displays the D/F or DEF status as judged from defroster position signal.

Test item

Operation

Description

A/C INDICATOR

A/C indicator is turned ON.

Off

A/C indicator is turned OFF.

Monitor item [UNIT]

Description

TURN SIGNAL R
[Off/On]

Displays the status of TURN RH switch in combination switch judged by the combination switch reading func-
tion.

TURN SIGNAL L
[Off/On]

Displays the status of the TURN LH switch in combination switch judged by the combination switch reading
function.

HI BEAM SW
[Off/On]

Displays the status of HI BEAM switch in combination switch judged by the combination switch reading func-
tion.

HEAD LAMP SW 1
[Off/On]

Displays the status of HEADLAMP 1 switch in combination switch judged by the combination switch reading
function.

HEAD LAMP SW 2
[Off/On]

Displays the status of HEADLAMP 2 switch in combination switch judged by the combination switch reading
function.

TAIL LAMP SW
[Off/On]

Displays the status of TAIL LAMP switch in combination switch judged by the combination switch reading
function.

PASSING SW
[Off/On]

Displays the status of PASSING switch in combination switch judged by the combination switch reading func-
tion.

AUTO LIGHT SW
[Off/On]

NOTE:
This item is indicated, but not monitored.

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-113

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

BCM

BCM : CONSULT Function (BCM - BCM)

INFOID:0000000009751663

WORK SUPPORT

IMMU

IMMU : CONSULT Function (BCM - IMMU)

INFOID:0000000010286808

WORK SUPPORT

ACTIVE TEST

BATTERY SAVER

BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)

INFOID:0000000010286822

WORK SUPPORT

FR FOG SW
[Off/On]

Displays the status of FR FOG switch in combination switch judged by the combination switch reading func-
tion.

RR FOG SW
[Off/On]

NOTE:
This item is indicated, but not monitored.

FR WIPER HI
[Off/On]

Displays the status of FR WIPER HI switch in combination switch judged by the combination switch reading
function.

FR WIPER LOW
[Off/On]

Displays the status of FR WIPER LOW switch in combination switch judged by the combination switch read-
ing function.

FR WIPER INT
[Off/On]

Displays the status of FR WIPER INT switch in combination switch judged by the combination switch reading
function.

FR WASHER SW
[Off/On]

Displays the status of FR WASHER switch in combination switch judged by the combination switch reading
function.

INT VOLUME
[1 - 7]

Displays the status of wiper intermittent dial position judged by the combination switch reading function.

RR WIPER ON
[Off/On]

Displays the status of RR WIPER switch in combination switch judged by the combination switch reading
function.

RR WIPER INT
[Off/On]

Displays the status of RR WIPER INT switch in combination switch judged by the combination switch reading
function.

RR WASHER SW
[Off/On]

Displays the status of RR WASHER switch in combination switch judged by the combination switch reading
function.

Monitor item [UNIT]

Description

Item

Description

RESET SETTING VALUE

Return a value set with WORK SUPPORT of each system to a default value in factory shipment.

Service item

Description

CONFIRM DONGLE ID

It is possible to check that dongle unit is applied to the vehicle.

Test item

Description

THEFT IND

This test is able to check security indicator lamp operation. Security indicator lamp will be
turned on when “ON” on CONSULT screen is touched.

Revision: 2013 October

2014 JUKE

BCS-114

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

*:Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST

TRUNK

Service item

Setting item

Setting

ROOM LAMP TIMER SET

MODE 1

30 min.

Sets the interior room lamp battery saver timer operating
time.
NOTE:
The factor setting is 10 minutes. The setting cannot be re-
turned to the factory setting, when the setting is changed
once.

MODE 2

60 min.

MODE 3

15 min.

Monitor item

[Unit]

Description

IGN ON SW
[On/Off]

Indicated [On/Off] condition of ignition switch in ON position

KEY ON SW
[On/Off]

Indicated [On/Off] condition of key switch

DOOR SW-DR
[On/Off]

Indicated [On/Off] condition of front door switch (driver side)

DOOR SW-AS
[On/Off]

Indicated [On/Off] condition of front door switch (passenger side)

DOOR SW-RR
[On/Off]

Indicated [On/Off] condition of rear door switch RH

DOOR SW- RL
[On/Off]

Indicated [On/Off] condition of rear door switch LH

BACK DOOR SW
[On/Off]

Indicated [On/Off] condition of back door switch

LOCK STATUS
[On/Off]

The switch status input from door lock status switch (driver side)

CDL LOCK SW
[On/Off]

Indicates [On/Off] condition of door lock and unlock switch

CDL UNLOCK SW
[On/Off]

Indicates [On/Off] condition of door lock and unlock switch

KEYLESS LOCK
[On/Off]

Indicates [On/Off] condition of lock signal from keyfob

KEYLESS UNLOCK
[On/Off]

Indicates [On/Off] condition of unlock signal from keyfob

TRNK/HAT MNTR
[On/Off]

NOTE:
This item is displayed, but cannot be tested

KEY CYL LK-SW
[On/Off]

Indicated [On/Off] condition of lock signal from door key cylinder

KEY CYL UN-SW
[On/Off]

Indicated [On/Off] condition of unlock signal from door key cylinder

ACC ON SW
[On/Off]

Indicates [On/Off] condition of ignition switch in ACC position

Test item

Operation

Description

BATTERY SAVER

Off

Cuts the interior room lamp power supply.

Outputs the interior room lamp power supply.

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-115

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

TRUNK : CONSULT Function (BCM - TRUNK)

INFOID:0000000010286786

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

THEFT ALM

THEFT ALM : CONSULT Function (BCM - THEFT)

INFOID:0000000010286807

WORK SUPPORT

ACTIVE TEST

RETAIND PWR

RETAIND PWR : CONSULT Function (BCM - RETAINED PWR)

INFOID:0000000010286811

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

SIGNAL BUFFER

Monitor Item

Contents

KEY ON SW

Indicates [On/Off] condition of key switch.

LOCK STATUS

NOTE:
This item is displayed, but cannot be monitored.

VEHICLE SPEED

Indicates [Km/h] condition of vehicle speed signal from combination meter.

IGN ON SW

Indicates [On/Off] condition of ignition switch.

TRNK OPNR SW

NOTE:
This item is displayed, but cannot be monitored.

KYLS TRNK/HAT

NOTE:
This item is displayed, but cannot be monitored.

Service Item

Description

SECURITY ALARM SET

This mode is able to confirm and change security alarm ON-OFF setting.

THEFT ALM TRG

The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.

Test Item

Description

THEFT IND

This test is able to check security indicator lamp operation. Security indicator lamp will be
turned on when “ON” on CONSULT screen is touched.

VEHICLE SECURITY HORN

This test is able to check horn operation. Horn will be activated for 0.5 seconds after “ON” on
CONSULT screen is touched.

HEADLAMP (HI)

This test is able to check headlamp (HI) operation. Headlamps (HI) will be activated for 0.5
seconds after “ON” on CONSULT screen is touched.

FLASHER

This test is able to check hazard warning lamp operation. Hazard warning lamps will be acti-
vated after “LH” or “RH” on CONSULT screen is touched.

Monitor Item

Description

DOOR SW-DR

Indicates [ON/OFF] condition of driver side door switch.

DOOR SW-AS

Indicates [ON/OFF] condition of passenger side door switch.

Revision: 2013 October

2014 JUKE

BCS-116

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER)

INFOID:0000000009751669

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST

PANIC ALARM

PANIC ALARM : CONSULT Function (BCM - PANIC ALARM)

INFOID:0000000010286809

ACTIVE TEST

AIR PRESSURE MONITOR

AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
TOR)

INFOID:0000000010286830

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SELF DIAGNOSTIC RESULT

Refer to

BCS-132, "DTC Index"

DATA MONITOR MODE

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Monitor item [UNIT]

Description

OIL PRESS SW
[Off/On]

NOTE:
This item is indicated, but not monitored.

BRAKE SW
[Off/On]

Displays the switch status input from stop lamp switch.

Test item

Operation

Description

OIL PRESSURE SW

Off

NOTE:
This item is indicated, but not tested.

Test item

Description

VEHICLE SECURITY HORN

This test is able to check horn operation.
Horn is activated for 0.5 seconds after “ON” on CONSULT screen touched.

HEAD LAMP (HI)

This test is able to check headlamp (HI) operation.
Headlamps (HI) will be activated after “ON” on CONSULT screen touched.

Diagnosis mode

Function Description

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Work Support

Components can be quickly and accurately adjusted.

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-117

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

ACTIVE TEST MODE

NOTE:
After completing the work below, perform an active test.
1.

Check ID registration state and perform self-diagnosis.

Erase the self-diagnosis result history.

WORK SUPPORT

Monitor item (Unit)

Remarks

AIR PRESS FL
(kPa, kg/cm2 or Psi)

Tire pressure

AIR PRESS FR
(kPa, kg/cm2 or Psi)

AIR PRESS RR
(kPa, kg/cm2 or Psi)

AIR PRESS RL
(kPa, kg/cm2 or Psi)

ID REGST FL1
(Yet, Done)

Registration ID

ID REGST FR1
(Yet, Done)

ID REGST RR1
(Yet, Done)

ID REGST RL1
(Yet, Done)

WARNING LAMP
(On/Off)

Low tire pressure warning lamp

BUZZER
(On/Off)

NOTE:
This item is displayed, but cannot be use this item.

Item

Description

WARNING LAMP

Low tire pressure warning lamp can be turned ON arbitrarily.

ID REGIST WARNING

NOTE:
Displayed but not used in TPMS.

RUN FLAT TIRE W/L

NOTE:
Displayed but not used in TPMS.

FLASHER

Turn signal lamps can be turned ON arbitrarily.

RUN FLAT TIRE W/R

NOTE:
Displayed but not used in TPMS.

Item

Description

ID READ

Registered tire pressure sensor ID can be displayed.

ID REGIST

Tire pressure sensor ID can be registered.

Revision: 2013 October

2014 JUKE

Nissan Juke (2014 year). Service Repair Manual - part 19