Nissan Juke (2012 year). Service Repair Manual - part 67

U1010 CONTROL UNIT (CAN)

DLN-77

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

U1010 CONTROL UNIT (CAN)

Description

INFOID:0000000007580223

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit communicate data but selectively reads required data only.

DTC Logic

INFOID:0000000007580224

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1.

Turn the ignition switch OFF to ON.

2.

Perform self-diagnosis for “ALL MODE AWD/4WD”.

Is DTC “U1010” detected?

YES >> Proceed 

to 

DLN-77, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007580225

1.

CHECK AWD CONTROL MODULE

Check AWD control module harness connector for disconnection and deformation.

Is the inspection result normal? 

YES

>> Replace AWD control module. Refer to 

DLN-92, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

U1010

CONTROL UNIT (CAN)

Detecting error during the initial diagno-
sis of CAN controller of AWD control 
module.

Internal malfunction of AWD control 
module

Revision: 2011 October

2012 JUKE

DLN-78

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000007580226

1.

CHECK AWD CONTROL MODULE POWER SUPPLY (1)

1.

Turn the ignition switch OFF.

2.

Disconnect AWD control module harness connector.

3.

Check the voltage between AWD control module harness connector and ground.

4.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

5.

Check the voltage between AWD control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK AWD CONTROL MODULE POWER SUPPLY (2)

1.

Turn the ignition switch OFF.

2.

Check the 10A fuse (#33).

3.

Check the harness for open or short between AWD control module harness connector No.1 terminal and
10A (#33).

Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit. Refer to 

PG-11, "Wiring Diagram - BAT-

TERY POWER SUPPLY -"

.

NO

>> Repair or replace error-detected parts.

3.

CHECK AWD CONTROL MODULE POWER SUPPLY (3)

1.

Turn the ignition switch OFF.

2.

Check the voltage between AWD control module harness connector and ground.

3.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

4.

Check the voltage between AWD control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

AWD control module

—

Voltage

Connector

Terminal

B47

1

Ground

11 – 13 V

AWD control module

—

Voltage

Connector

Terminal

B47

1

Ground

11 – 13 V

AWD control module

—

Voltage

Connector

Terminal

B47

3

Ground

0 V

AWD control module

—

Voltage

Connector

Terminal

B47

3

Ground

11 – 13 V

Revision: 2011 October

2012 JUKE

POWER SUPPLY AND GROUND CIRCUIT

DLN-79

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

4.

CHECK AWD CONTROL MODULE POWER SUPPLY (4)

1.

Turn the ignition switch OFF.

2.

Check the 10A fuse (#3).

3.

Check the harness for open or short between AWD control module harness connector No.3 terminal and
10A (#3).

Is the inspection result normal?

YES

>> Perform the trouble diagnosis for ignition power supply circuit. Refer to 

PG-23, "Wiring Diagram -

IGNITION POWER SUPPLY -"

.

NO

>> Repair or replace error-detected parts.

5.

CHECK AWD SOLENOID POWER SUPPLY (1)

1.

Turn the ignition switch OFF.

2.

Disconnect AWD control module harness connector.

3.

Check the voltage between AWD control module harness connector and ground.

4.

Turn the ignition switch OFF to ON.

CAUTION:

Never start the engine.

5.

Check the voltage between AWD control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> GO TO 6.

6.

CHECK AWD SOLENOID POWER SUPPLY (2)

1.

Turn the ignition switch OFF.

2.

Check the 10A fuse (#12).

3.

Check the harness for open or short between AWD control module harness connector No.12 and the 10A
fuse (#12).

Is the inspection result normal?

YES

>> Perform the trouble the diagnosis for power supply circuit. Refer to 

PG-11, "Wiring Diagram - BAT-

TERY POWER SUPPLY -"

.

NO

>> Repair or replace error-detected parts.

7.

CHECK AWD CONTROL MODULE GROUND

1.

Turn the ignition switch OFF.

2.

Check the continuity between AWD control module harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace error-detected parts.

AWD control module

—

Voltage

Connector

Terminal

B47

12

Ground

11 – 13 V

AWD control module

—

Voltage

Connector

Terminal

B47

12

Ground

11 – 13 V

AWD control module

—

Continuity

Connector

Terminal

B47

10

Ground

Existed

11

Revision: 2011 October

2012 JUKE

DLN-80

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

AWD WARNING LAMP

AWD WARNING LAMP

Component Function Check

INFOID:0000000007580227

1.

CHECK AWD WARNING LAMP FUNCTION 

Check that AWD warning lamp turns ON when turn the ignition switch ON. Then, AWD warning lamp turns
OFF approx. 1 second after the engine start.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to 

DLN-80, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000007580228

1.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Perform the trouble diagnosis for power supply and ground circuit. Refer to 

DLN-78, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the error-detected parts.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

DLN-32, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK AWD WARNING LAMP SIGNAL

With CONSULT

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check “WARNING LAMP” in “DATA MONITOR” for “ALL MODE AWD/4WD”.

Does the item on “DATA MONITOR” indicate “On”?

YES

>> Perform the trouble diagnosis for combination meter power supply circuit. Refer to 

MWI-42,

"COMBINATION METER : Diagnosis Procedure"

.

NO

>> Replace AWD control module. Refer to 

DLN-92, "Removal and Installation"

.

Revision: 2011 October

2012 JUKE

AWD MODE INDICATOR LAMP (AWD-V)

DLN-81

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

AWD MODE INDICATOR LAMP (AWD-V)

Component Function Check

INFOID:0000000007580229

1.

AWD MODE INDICATOR LAMP OPERATION CHECK

1.

Turn the ignition switch ON.

2.

Set AWD mode switch to “AWD-V”.

3.

Check that AWD mode indicator lamp (AWD-V) turns on. 

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to 

DLN-81, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000007580230

1.

CHECK AWD WARNING LAMP

1.

Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

2.

Stop the vehicle.

Does AWD warning lamp turn ON?

YES

>> Proceed to 

DLN-80, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK AWD MODE SWITCH

Perform the trouble diagnosis for AWD mode switch. Refer to 

DLN-44, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the error-detected parts.

3.

CHECK AWD MODE INDICATOR LAMP SIGNAL

With CONSULT

1.

Start the engine.

CAUTION:

Never drive the vehicle.

2.

Change AWD mode switch to “AWD-V” from “2WD”.

3.

Check “INDICATOR” in “DATA MONITOR” for “ALL MODE AWD/4WD”.

Does the item on “DATA MONITOR” indicate “AWD-V”?

YES

>> GO TO 4.

NO

>> Replace AWD control module. Refer to 

DLN-92, "Removal and Installation"

.

4.

CHECK COMBINATION METER POWER SUPPLY CIRCUIT

Perform the trouble diagnosis for combination meter power supply circuit. Refer to 

MWI-42, "COMBINATION

METER : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace the error-detected parts.

Revision: 2011 October

2012 JUKE

DLN-82

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

AWD MODE INDICATOR LAMP (AWD)

AWD MODE INDICATOR LAMP (AWD)

Component Function Check

INFOID:0000000007580231

1.

AWD MODE INDICATOR LAMP OPERATION CHECK

Check that AWD mode indicator lamp (AWD) turns on for approximately 1 second after the ignition switch is
turned ON.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to 

DLN-82, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000007580232

1.

CHECK AWD WARNING LAMP

1.

Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

2.

Stop the vehicle.

Does AWD warning lamp turn ON?

YES

>> Proceed to 

DLN-80, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK AWD MODE SWITCH

Perform the trouble diagnosis for AWD mode switch. Refer to 

DLN-44, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the error-detected parts.

3.

CHECK AWD MODE INDICATOR LAMP SIGNAL

With CONSULT

1.

Start the engine.

CAUTION:

Stop the vehicle.

2.

Change AWD mode switch to “AWD” from “AWD-V”.

3.

Check “INDICATOR” in “DATA MONITOR” for “ALL MODE AWD/4WD”.

Does the item on “DATA MONITOR” indicate “AWD”?

YES

>> GO TO 4.

NO

>> Replace AWD control module. Refer to 

DLN-92, "Removal and Installation"

.

4.

CHECK COMBINATION METER POWER SUPPLY CIRCUIT

Perform the trouble diagnosis for combination meter power supply circuit. Refer to 

MWI-42, "COMBINATION

METER : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace the error-detected parts.

Revision: 2011 October

2012 JUKE

AWD WARNING LAMP DOES NOT TURN ON

DLN-83

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

SYMPTOM DIAGNOSIS

AWD WARNING LAMP DOES NOT TURN ON

Description

INFOID:0000000007580233

AWD warning lamp does not turn ON when the ignition switch is turned to ON.

Diagnosis Procedure

INFOID:0000000007580234

1.

CHECK AWD WARNING LAMP

Perform the trouble diagnosis for AWD warning lamp. Refer to 

DLN-80, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Check each harness connector pin terminal for malfunction or disconnection.

NO

>> Repair or replace the error-detected parts.

Revision: 2011 October

2012 JUKE

DLN-84

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21B]

AWD WARNING LAMP DOES NOT TURN OFF

AWD WARNING LAMP DOES NOT TURN OFF

Description

INFOID:0000000007580235

AWD warning lamp does not turn OFF approx. 1 second after the engine started.

Diagnosis Procedure

INFOID:0000000007580236

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ALL MODE AWD/4WD”.

Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

DLN-32, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK AWD WARNING LAMP

Perform the trouble diagnosis of the AWD warning lamp. Refer to 

DLN-80, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the error-detected parts.

3.

CHECK AWD CONTROL MODULE POWER SUPPLY AND GRAND CIRCUIT

Perform the trouble diagnosis of power supply and ground circuit. Refer to 

DLN-78, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Check each harness connector pin terminal for malfunction or disconnection.

NO

>> Repair or replace the error-detected parts.

Revision: 2011 October

2012 JUKE

HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS

DLN-85

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS

Description

INFOID:0000000007580237

Heavy tight-corner braking symptom occurs when the vehicle is driven and the steering wheel is turned fully to
either side after the engine is started.
NOTE:
Light tight-corner braking symptom may occur depending on driving conditions. This is not malfunction.

Diagnosis Procedure

INFOID:0000000007580238

1.

PERFORM ECM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ENGINE”.

Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

EC-102, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ALL MODE AWD/4WD”.

Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

DLN-32, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK AWD SOLENOID

Perform the trouble diagnosis of the AWD solenoid. Refer to 

DLN-54, "Diagnosis Procedure"

 (Left side), 

DLN-

57, "Diagnosis Procedure"

 (Right side).

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the error-detected parts.

4.

CHECK ELECTRIC CONTROLLED COUPLING

1.

Turn the ignition switch OFF.

2.

Set the transaxle to neutral. Release the parking brake.

3.

Lift up the vehicle.

4.

Rotate the propeller shaft by hand.

5.

Hold rear wheel of right and left lightly.

Does rear wheel rotate?

YES

>> Replace electric controlled coupling for mechanical malfunction (clutch sticking etc.). Refer to

DLN-145, "Removal and Installation"

.

NO

>> Check each harness connector pin terminal for disconnection.

Revision: 2011 October

2012 JUKE

DLN-86

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21B]

VEHICLE DOES NOT ENTER AWD MODE

VEHICLE DOES NOT ENTER AWD MODE

Description

INFOID:0000000007580239

Vehicle does not enter 4-wheel drive mode even though AWD warning lamp turned to OFF.

Diagnosis Procedure

INFOID:0000000007580240

1.

CHECK AWD WARNING LAMP

Turn the ignition switch ON.

CAUTION:

Never start the engine.

Does AWD warning lamp turn ON?

YES

>> GO TO 2.

NO

>> Proceed to 

DLN-80, "Diagnosis Procedure"

.

2.

CHECK PARKING BRAKE SWITCH SIGNAL

With CONSULT

Check “PKB SW” in “DATA MONITOR” for “ALL MODE AWD/4WD”.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Proceed to 

BRC-108, "Diagnosis Procedure"

.

3.

CRUISE TEST

Drive the vehicle for a period of time.

Does any symptom occur?

YES

>> Replace electric controlled coupling for mechanical malfunction (mechanical engagement of

clutch is not possible). Refer to 

DLN-145, "Removal and Installation"

.

NO

>> Check each harness connector pin terminal for disconnection.

Monitor Item

Condition

Status

PKB SW

When the parking brake switch is operation.

On

When the parking brake switch is not operation.

Off

Revision: 2011 October

2012 JUKE

AWD WARNING LAMP BLINKS QUICKLY

DLN-87

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

AWD WARNING LAMP BLINKS QUICKLY

Description

INFOID:0000000007580241

While driving, AWD warning lamp blinks 2 times in 1 second and it turns OFF after 1 minute.
NOTE:
• This symptom protects drivetrain parts when a heavy load is applied to the electric controlled coupling and

multiple disc clutch temperature increases. Also, optional distribution of torque sometimes becomes rigid
before lamp blinks quickly. Both cases are not malfunction. Refer to 

DLN-31, "Protection Function"

.

• When this symptom occurs, stop vehicle and allow it to idle for some times. Blinking will stop and system will

be restored.

Revision: 2011 October

2012 JUKE

DLN-88

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21B]

AWD WARNING LAMP BLINKS SLOWLY

AWD WARNING LAMP BLINKS SLOWLY

Description

INFOID:0000000007580242

AWD warning lamp blinks at approximately 2 seconds intervals while driving.

Diagnosis Procedure

INFOID:0000000007580243

1.

CHECK VEHICLE SPEED SIGNAL

With CONSULT

1.

Turn the ignition switch ON.

2.

Check that each value of “WHEEL SPD SEN FR”, “WHEEL SPD SEN FL”, “WHEEL SPD SEN RR”, and
“WHEEL SPD SEN RL” in “DATA MONITOR” for “ALL MODE AWD/4WD” is almost equal.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Proceed to 

DLN-41, "Diagnosis Procedure"

.

2.

CHECK TIRE

Check the following.
• Tire pressure
• Tire wear condition
• Front and rear tire size (There is no difference between front and rear tires.)
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

TERMINAL INSPECTION

Check AWD control module harness connector for disconnection.

Is the inspection result normal?

YES

>> Replace AWD control module. Refer to 

DLN-92, "Removal and Installation"

.

NO

>> Repair or replace the error-detected parts.

Revision: 2011 October

2012 JUKE

DECREASE IN TURNING PERFORMANCE

DLN-89

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

DECREASE IN TURNING PERFORMANCE

Description

INFOID:0000000007580244

Turning performance decreases when driving in AWD-V mode or AWD mode.

Diagnosis Procedure

INFOID:0000000007580245

1.

PERFORM EPS CONTROL UNIT SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “EPS”.

Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

STC-13, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ALL MODE AWD/4WD”.

Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to 

DLN-32, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK AWD SOLENOID

Perform the trouble diagnosis of the AWD solenoid. Refer to 

DLN-54, "Diagnosis Procedure"

 (Left side), 

DLN-

57, "Diagnosis Procedure"

 (Right side).

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the error-detected parts.

4.

CHECK ELECTRIC CONTROLLED COUPLING

1.

Turn the ignition switch OFF.

2.

Set the transaxle to neutral. Release the parking brake.

3.

Lift up the vehicle.

4.

Rotate the propeller shaft.

5.

Hold the rear wheel of right and left lightly.

Does the rear wheel rotate?

YES

>> Replace electric controlled coupling for mechanical malfunction (clutch sticking etc.). Refer to

DLN-145, "Removal and Installation"

.

NO

>> Check each harness connector pin terminal for disconnection.

Revision: 2011 October

2012 JUKE

DLN-90

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY21B]

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NVH Troubleshooting Chart

INFOID:0000000007580246

Use the chart below to find the cause of the symptom. The numbers indicate the order of the inspection. If necessary, repair or replace these
parts.

Reference

DLN-91, "

Insp

ectio

n

"

DLN-97, "

Ex

pl

od

ed

 V

iew

"

DLN-97, "

Ex

pl

od

ed

 V

iew

"

DLN-1

1

0, "

Insp

ectio

n

"

DLN-1

1

6, "

Insp

ectio

n

"

SUSPECTED PARTS
(Possible cause)

T

R

ANSFER OIL (Level 

low

)

T

R

ANSFER OIL (W

rong)

T

R

ANSFER OIL (Level 

too high)

LI

QUI

D

 GASKET

 (Dam

ag

ed

)

OIL

 SEAL

 (W

orn

 or da

ma

ge

d

)

GEAR

 (W

orn

 o

r 

da

ma

ge

d)

B

EARING (W

orn

 or 

da

ma

ge

d)

Symptom

Noise

1

2

3

3

3

Transfer  oil  leakage

3

1

2

2

Revision: 2011 October

2012 JUKE

TRANSFER OIL

DLN-91

< PERIODIC MAINTENANCE >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

PERIODIC MAINTENANCE

TRANSFER OIL

Inspection

INFOID:0000000007580247

OIL LEAKAGE

Check transfer surrounding area (oil seal, drain plug, filler plug, and transfer case etc.) for oil leakage.

OIL LEVEL

1.

Remove filler plug (1) and gasket. Then check that oil is filled up
from mounting hole for the filler plug.

CAUTION:

Never start engine while checking oil level.

2.

Before installing filler plug, set a new gasket. Install filler plug on
transfer and tighten to the specified torque. Refer to 

DLN-117,

"Exploded View"

.

CAUTION:

Never reuse gasket.

Draining

INFOID:0000000007580248

1.

Run the vehicle to warm up the transfer unit sufficiently.

2.

Stop the engine and remove the drain plug (1) and gasket to
drain the transfer oil.

3.

Before installing drain plug, set a new gasket. Install drain plug
on the transfer and tighten to the specified torque. Refer to 

DLN-

117, "Exploded View"

.

CAUTION:

Never reuse gasket.

Refilling

INFOID:0000000007580249

1.

Remove filler plug (1) and gasket. Then fill oil up to mounting
hole for the filler plug.

CAUTION:

Carefully fill the oil. (Fill up for approximately 3 minutes.)

2.

Leave the vehicle for 3 minutes, and check the oil level again.

3.

Before installing filler plug, set a new gasket. Install filler plug on transfer and tighten to the specified
torque. Refer to 

DLN-117, "Exploded View"

.

CAUTION:

Never reuse gasket.

: Vehicle front

JSDIA2080ZZ

: Vehicle front

JSDIA2081ZZ

: Vehicle front

Oil and viscosity

: Refer to 

MA-10, "Fluids 

and Lubricants"

.

Oil capacity

: Refer to 

DLN-121, "Gen-

eral Specifications"

.

JSDIA2080ZZ

Revision: 2011 October

2012 JUKE

DLN-92

< REMOVAL AND INSTALLATION >

[TRANSFER: TY21B]

AWD CONTROL MODULE

REMOVAL AND INSTALLATION

AWD CONTROL MODULE

Exploded View

INFOID:0000000007580250

Removal and Installation

INFOID:0000000007580251

REMOVAL

1.

Turn the ignition switch OFF.

2.

Remove front seat (left side). Refer to 

SE-18, "Removal and Installation"

.

3.

Remove dush side finisher (left side). Refer to 

INT-20, "DASH SIDE FINISHER : Removal and Installa-

tion"

.

4.

Remove front and rear kicking plate inner. Refer to 

INT-18, "KICKING PLATE INNER : Removal and

Installation"

.

5.

Remove rear seat cushion. Refer to 

SE-26, "SEAT CUSHION : Removal and Installation"

.

6.

Remove outer anchor of front seat belt (passenger side). Refer to 

SB-4, "Exploded View"

.

7.

Remove harness clip.

8.

Turn floor carpet. Refer to 

INT-23, "Removal and Installation"

.

9.

Disconnect AWD control module harness connector.

10. Remove AWD control module mounting nuts.
11. Remove AWD control module.

INSTALLATION

Note the following, and install in the reverse order of removal.
• When installing AWD control module, install it following procedure.

1.

AWD control module

2.

AWD control module harness con-
nector

: Vehicle front

: N·m (kg-m, in-lb)

JSDIA2374GB

Revision: 2011 October

2012 JUKE