Nissan Juke (2012 year). Service Repair Manual - part 4

AV

STEERING SWITCH SIGNAL GND CIRCUIT (STEERING SWITCH TO TEL 

ADAPTER UNIT)

AV-45

< DTC/CIRCUIT DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

Component Inspection

INFOID:0000000007577914

Measure the resistance between the steering switch connector.

Standard

JSNIA2808GB

Steering switch

Condition

Resistance 

(Approx.) 

Ω

Terminal

Terminal

14

17

 

 switch ON

709 – 737

SEEK DOWN switch 
ON

315 – 327

SEEK UP switch ON

119 – 123

SOURCE switch ON

0

15

 switch ON

315 – 327

VOL UP switch ON

119 – 123

VOL DOWN switch ON

0

Revision: 2011 October

2012 JUKE

AV-46

< DTC/CIRCUIT DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

STEERING SWITCH SIGNAL A CIRCUIT (TEL ADAPTER UNIT TO AUDIO UNIT)

STEERING SWITCH SIGNAL A CIRCUIT (TEL ADAPTER UNIT TO AUDIO
UNIT)

Description

INFOID:0000000007577915

• Transmits the steering switch signal to TEL adapter unit.
• Transmits the steering switch signal to audio unit via TEL adapter unit.

Diagnosis Procedure

INFOID:0000000007577916

1.

CHECK STEERING SWITCH SIGNAL A CIRCUIT (TEL ADAPTER UNIT TO AUDIO UNIT)

1.

Turn ignition switch OFF.

2.

Disconnect audio unit connector and TEL adapter unit connector.

3.

Check continuity between audio unit harness connector and TEL adapter unit harness connector.

4.

Check continuity between audio unit harness connector and ground.

Is inspection result normal?

YES

>> GO TO 2.

NO

>> Repair harness or connector.

2.

CHECK AUDIO UNIT VOLTAGE

1.

Connect audio unit connector and TEL adapter unit connector.

2.

Turn ignition switch ON.

3.

Check voltage between audio unit harness connector terminals.

Is inspection result normal?

YES

>> Replace TEL adapter unit. Refer to 

AV-65, "Removal and Installation"

.

NO

>> Replace audio unit. Refer to 

AV-59, "Removal and Installation"

.

Audio unit

TEL adapter unit

Continuity

Connector

Terminal

Connector

Terminal

M91

6

M127

17

Existed

Audio unit

Ground

Continuity

Connector

Terminal

M91

6

Not existed

Probe

Standard

Reference value

(Approx.)

(+)

(

−

)

Audio unit

Connector

Terminal

Connector

Terminal

M91

6

M91

15

0 – 3.3 V

3.3 V

Revision: 2011 October

2012 JUKE

AV

STEERING SWITCH SIGNAL B CIRCUIT (TEL ADAPTER UNIT TO AUDIO UNIT)

AV-47

< DTC/CIRCUIT DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

STEERING SWITCH SIGNAL B CIRCUIT (TEL ADAPTER UNIT TO AUDIO
UNIT)

Description

INFOID:0000000007577917

• Transmits the steering switch signal to TEL adapter unit.
• Transmits the steering switch signal to audio unit via TEL adapter unit.

Diagnosis Procedure

INFOID:0000000007577918

1.

CHECK STEERING SWITCH SIGNAL B CIRCUIT (TEL ADAPTER UNIT TO AUDIO UNIT)

1.

Turn ignition switch OFF.

2.

Disconnect audio unit connector and TEL adapter unit connector.

3.

Check continuity between audio unit harness connector and TEL adapter unit harness connector.

4.

Check continuity between audio unit harness connector and ground.

Is inspection result normal?

YES

>> GO TO 2.

NO

>> Repair harness or connector.

2.

CHECK AUDIO UNIT VOLTAGE

1.

Connect audio unit connector and TEL adapter unit connector.

2.

Turn ignition switch ON.

3.

Check voltage between audio unit harness connector terminals.

Is inspection result normal?

YES

>> Replace TEL adapter unit. Refer to 

AV-65, "Removal and Installation"

.

NO

>> Replace audio unit. Refer to 

AV-59, "Removal and Installation"

.

Audio unit

TEL adapter unit

Continuity

Connector

Terminal

Connector

Terminal

M91

16

M127

18

Existed

Audio unit

Ground

Continuity

Connector

Terminal

M91

16

Not existed

Probe

Standard

Reference value

(Approx.)

(+)

(

−

)

Audio unit

Connector

Terminal

Connector

Terminal

M91

16

M91

15

0 – 3.3 V

3.3 V

Revision: 2011 October

2012 JUKE

AV-48

< DTC/CIRCUIT DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

STEERING SWITCH SIGNAL GND CIRCUIT (TEL ADAPTER UNIT TO AUDIO 

UNIT)

STEERING SWITCH SIGNAL GND CIRCUIT (TEL ADAPTER UNIT TO AU-
DIO UNIT)

Description

INFOID:0000000007577919

• Transmits the steering switch signal to TEL adapter unit.
• Transmits the steering switch signal to audio unit via TEL adapter unit.

Diagnosis Procedure

INFOID:0000000007577920

1.

CHECK STEERING SWITCH SIGNAL GROUND CIRCUIT (TEL ADAPTER UNIT TO AUDIO UNIT)

1.

Turn ignition switch OFF.

2.

Disconnect audio unit connector and TEL adapter unit connector.

3.

Check continuity between audio unit harness connector and TEL adapter unit harness connector.

Is inspection result normal?

YES

>> GO TO 2.

NO

>> Repair harness or connector.

2.

CHECK GROUND CIRCUIT

1.

Connect audio unit connector.

2.

Check continuity between audio unit harness connector and ground.

Is inspection result normal?

YES

>> Replace TEL adapter unit. Refer to 

AV-65, "Removal and Installation"

.

NO

>> Replace audio unit. Refer to 

AV-59, "Removal and Installation"

.

Audio unit

TEL adapter unit

Continuity

Connector

Terminal

Connector

Terminal

M91

15

M127

19

Existed

Audio unit

Ground

Continuity

Connector

Terminal

M91

15

Existed

Revision: 2011 October

2012 JUKE

AV

COMMUNICATION SIGNAL CIRCUIT

AV-49

< DTC/CIRCUIT DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

COMMUNICATION SIGNAL CIRCUIT

Description

INFOID:0000000007577921

Satellite radio tuner and audio unit are connected with a serial communication. They transmit the operation
signal from audio unit to satellite radio tuner.

Diagnosis Procedure

INFOID:0000000007577922

1.

CHECK CONTINUITY COMMUNICATION SIGNAL (AUDIO

−

SAT) CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect satellite radio tuner connector and audio unit connector.

3.

Check continuity between satellite radio tuner harness connector and audio unit harness connector.

4.

Check continuity between satellite radio tuner harness connector and ground.

Is inspection result OK?

YES

>> GO TO 2.

NO

>> Repair harness or connector.

2.

CHECK AUDIO UNIT

1.

Connect audio unit connector.

2.

Turn ignition switch ON.

3.

Check voltage between audio unit harness connector and ground.

Is inspection result OK?

YES

>> GO TO 3.

NO

>> Replace audio unit. Refer to 

AV-59, "Removal and Installation"

.

3.

CHECK SATELLITE RADIO TUNER

1.

Turn ignition switch OFF.

2.

Disconnect audio unit connector, and connect satellite radio tuner connector.

3.

Turn ignition switch ON.

4.

Check voltage between satellite radio tuner harness connector and ground.

Satellite radio tuner

Audio unit

Continuity

Connector

Terminal

Connector

Terminal

B69

9

M93

39

Existed

10

40

Existed

Satellite radio tuner

Ground

Continuity

Connector

Terminal

B69

9

Not existed

10

Probe

Reference value

(Approx.)

(+)

(

−

)

Audio unit

Ground

Connector

Terminal

M93

39

4.0 V

Revision: 2011 October

2012 JUKE

AV-50

< DTC/CIRCUIT DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

COMMUNICATION SIGNAL CIRCUIT

Is inspection result OK?

YES

>> GO TO 4.

NO

>> Replace satellite radio tuner. Refer to 

AV-63, "Removal and Installation"

.

4.

CHECK COMMUNICATION SIGNAL (SAT TO AUDIO)

1.

Turn ignition switch OFF.

2.

Connect audio unit connector.

3.

Turn ignition switch ON.

4.

Check signal between satellite radio tuner harness connector and ground.

Is inspection result OK?

YES

>> GO TO 5.

NO

>> Replace satellite radio tuner. Refer to 

AV-63, "Removal and Installation"

.

5.

CHECK COMMUNICATION SIGNAL (AUDIO TO SAT)

Check signal between audio unit harness connector and ground.

Is inspection result OK?

YES

>> INSPECTION END

NO

>> Replace audio unit. Refer to 

AV-59, "Removal and Installation"

.

Probe

Reference value

(Approx.)

(+)

(

−

)

Satellite radio tuner

Ground

Connector

Terminal

B69

10

7.5 V

Probe

Condition

Standard

Reference value

(+)

(+)

Satellite radio tuner

Connector

Terminal

Connector

Terminal

B69

9

B69

15

When satel-
lite radio 
mode is se-
lected.

Waveform of 0.5 - 7.0 V 
is input.

PKIB5039J

Probe

Condition

Standard

Reference value

(+)

(+)

Audio unit

Ground

Connector

Terminal

M93

40

When satel-
lite radio 
mode is se-
lected.

Waveform of 1.5 - 6.0 V 
is input.

SKIA9301J

Revision: 2011 October

2012 JUKE

AV

REQUEST SIGNAL CIRCUIT (SAT TO AUDIO)

AV-51

< DTC/CIRCUIT DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

REQUEST SIGNAL CIRCUIT (SAT TO AUDIO)

Description

INFOID:0000000007577923

Request signal transmits the signal to recognize the connection of satellite radio tuner from satellite radio
tuner to audio unit.

Diagnosis Procedure

INFOID:0000000007577924

1.

CHECK CONTINUITY REQUEST SIGNAL CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect satellite radio tuner connector and audio unit connector.

3.

Check continuity between satellite radio tuner harness connector and audio unit harness connector.

4.

Check continuity between satellite radio tuner harness connector and ground.

Is inspection result OK?

YES

>> GO TO 2.

NO

>> Repair harness or connector.

2.

CHECK AUDIO UNIT

1.

Connect audio unit connector.

2.

Turn ignition switch ON.

3.

Check voltage between audio unit harness connector and ground.

Is inspection result OK?

YES

>> GO TO 3.

NO

>> Replace audio unit. Refer to 

AV-59, "Removal and Installation"

.

3.

CHECK CONTINUITY REQUEST SIGNAL

1.

Turn ignition switch OFF.

2.

Connect satellite radio tuner connector.

3.

Turn ignition switch ON.

4.

Check signal between satellite radio tuner harness connector and ground.

Satellite radio tuner

Audio unit

Continuity

Connector

Terminal

Connector

Terminal

B69

8

M93

38

Existed

Satellite radio tuner

Ground

Continuity

Connector

Terminal

B69

8

Not existed

Probe

Reference value

(Approx.)

(+)

(

−

)

Audio unit

Ground

Connector

Terminal

M93

38

4.0 V

Revision: 2011 October

2012 JUKE

AV-52

< DTC/CIRCUIT DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

REQUEST SIGNAL CIRCUIT (SAT TO AUDIO)

Is inspection result OK?

YES

>> INSPECTION END

NO

>> Replace satellite radio tuner. Refer to 

AV-63, "Removal and Installation"

.

Probe

Condition

Standard

Reference value

(+)

(+)

Satellite radio tuner

Connector

Terminal

Connector

Terminal

B69

8

B69

15

When satel-
lite radio 
mode is se-
lected.

Waveform of 0.5 - 7.0 V 
is input.

SKIA9299J

Revision: 2011 October

2012 JUKE

AV

AUDIO SYSTEM SYMPTOMS

AV-53

< SYMPTOM DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

SYMPTOM DIAGNOSIS

AUDIO SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000007577925

AUDIO SYSTEM

RELATED TO iPod

®

Trouble Diagnosis Chart by Symptom

Connect another iPod

®

 and check if the symptom is reproduced or not. If the symptom is reproduced, diag-

nose the vehicle. If no malfunction is detected, replace the iPod harness.
NOTE:
• It is unable to read a connection between iPod

®

 and iPod harness.

• Charging of iPod

®

 with no 5 V charging circuit is not supported. (e.g. iPod 1G mechanical scroll wheel, iPod

Classic 2G touch-sensitive wheel, and iPod Classic 3G 4 touch button)

Trouble diagnosis chart by symptom

iPod

®

 is a trademark of Apple inc., registered in the U.S. and other countries.

RELATED TO STEERING SWITCH

Symptoms

Check items

Possible malfunction location / Action to take

Audio sound is not heard.

No sound from all speakers.

Audio unit power supply and ground circuit.
Refer to 

AV-33, "AUDIO UNIT : Diagnosis Procedure"

.

Sound is not heard only from the 
specific places.

Sound signal circuit of malfunctioning system.

AM/FM radio is not received.

Other audio sounds are normal.

• Antenna amp. ON signal circuit.
• Antenna base
• Antenna feeder

Satellite radio is not received.

When “AUX” switch is pressed, it 
change to satellite radio mode.

• Satellite radio sound signal circuit
• Satellite radio antenna

When “AUX” switch is pressed, it 
does not change to satellite radio 
mode.

• Satellite radio tuner power supply and ground circuit.

Refer to 

AV-33, "SATELLITE RADIO TUNER : Diagnosis 

Procedure"

.

• Request signal circuit.

Refer to 

AV-51, "Diagnosis Procedure"

.

• Communication circuit between audio unit and satellite radio 

tuner. Refer to 

AV-49, "Diagnosis Procedure"

.

Symptoms

Check items

Possible malfunction location / Action to take

There is no sound from the iP-

od

®

.

Other audio sounds are normal.

• iPod sound signal circuit between audio unit and iPod 

adapter.

• iPod sound signal circuit between iPod

®

 and iPod 

adapter.

“iPod No connect” is displayed 
when “iPod” switch is pressed.

• iPod battery charging is normal.
• iPod software and hardware version 

are displayed when performing audio 
unit self-diagnosis.

Communication circuit between iPod

®

 and iPod adapter.

• iPod battery charging is normal.
• iPod software and hardware version 

are not displayed when performing au-
dio unit self-diagnosis.

AV communication circuit between audio unit and iPod 
adapter.

iPod battery charge does not work.

iPod adapter power supply and ground circuit.
Refer to 

AV-35, "iPod ADAPTER : Diagnosis Procedure"

.

iPod

®

 cannot charge the bat-

tery.

Not chargeable even when connecting 

other iPod

®

. Refer to NOTE.

iPod battery charge 5 V circuit between iPod

®

 and iPod 

adapter.

Revision: 2011 October

2012 JUKE

AV-54

< SYMPTOM DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

AUDIO SYSTEM SYMPTOMS

Symptoms

Possible malfunction location / Action to take

All steering switches are not operated.

Steering switch signal ground circuit. (steering switch to TEL adapter unit)
 Refer to 

AV-44, "Diagnosis Procedure"

.

“SOURCE”, “SEEK UP”, “VOL UP”, “SEEK DOWN” and 
“VOL DOWN” switches are not operated.

Steering switch signal ground circuit. (TEL adapter unit to audio unit)
Refer to 

AV-48, "Diagnosis Procedure"

.

Only specified switch cannot be operated.

Replace steering switch.
Refer to 

AV-69, "Removal and Installation"

.

“

 

”, “SEEK UP”, “SEEK DOWN” and “SOURCE” 

switches are not operated.

Steering switch signal A circuit. (steering switch to TEL adapter unit)
Refer to 

AV-40, "Diagnosis Procedure"

.

“SEEK UP”, “SEEK DOWN” and “SOURCE” switches are 
not operated.

Steering switch signal A circuit. (TEL adapter unit to audio unit)
Refer to 

AV-46, "Diagnosis Procedure"

.

“

”, “VOL UP” and “VOL DOWN” switches are not oper-

ated.

Steering switch signal B circuit. (steering switch to TEL adapter unit)
Refer to 

AV-42, "Diagnosis Procedure"

.

“VOL UP” and “VOL DOWN” switches are not operated.

Steering switch signal B circuit. (TEL adapter unit to audio unit)
Refer to 

AV-47, "Diagnosis Procedure"

.

Revision: 2011 October

2012 JUKE

AV

HANDS-FREE PHONE SYMPTOMS

AV-55

< SYMPTOM DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

HANDS-FREE PHONE SYMPTOMS

Symptom Table

INFOID:0000000007577926

RELATED TO HANDS-FREE PHONE

• Check that the cellular phone is corresponding type (Bluetooth

™

 enabled) when the hands-free related mal-

function vehicle is in service before performing a diagnosis.

• There is a case that malfunction occurs due to the version change of the phone type, etc. even though it is a

corresponding type. Therefore, confirm it by changing the cellular phone to another corresponding type
phone, and check that it operates normally. It is necessary to distinguish whether the cause is the vehicle or
cellular phone. Check to ensure the customer's phone is supported by checking the phone compatibility for
the hands-free system.

Simple Check for Bluetooth

™

 Communication

If cellular phone and TEL adapter unit cannot be connected with Bluetooth

™

 communication, following proce-

dure allows the technician to judge which device has malfunction.

1.

Turn on a cellular phone, not connecting Bluetooth

™

 communication.

2.

Start CONSULT, then start Windows

®

.

3.

Set CONSULT near a cellular phone.

4.

When operated Bluetooth

™

 registration by cellular phone, check

if CONSULT

*

 would be displayed on the device name.

(If other Bluetooth

™

device is located near cellular phone, a

name of the device would be displayed also.)
NOTE:
*:Displayed device name is “NISSAN-

”.

• If no device name is displayed, cellular phone is malfunction.

Repair the cellular phone first, then perform diagnosis. 

• If CONSULT is displayed on device name, cellular phone is nor-

mal. Perform diagnosis as per the following table. 

Trouble Diagnosis Chart by Symptom

RELATED TO STEERING SWITCH

JSNIA3798GB

Symptoms

Check items

Possible malfunction location/Action to take

Does not recognize cellular 
phone connection.

Repeat the registration of cellular phone.

TEL adapter unit

Hands-free phone cannot be 
established.

• Both the reception and the speech can-

not be performed.

• Audio can be operated by steering 

switch.

• TEL adapter unit power supply and ground circuit.

Refer to 

AV-34, "TEL ADAPTER UNIT : Diagnosis 

Procedure"

.

• Control signal circuit.

Refer to 

AV-38, "Diagnosis Procedure"

.

• AV communication circuit between audio unit and TEL 

adapter unit. 

• Both the reception and the speech can-

not be performed.

• Audio can be operated by steering 

switch.

TEL ON signal circuit.
Refer to 

AV-39, "Diagnosis Procedure"

.

The other party's voice cannot 
be heard by hands-free phone.

Audio system sound is normal.

Sound signal (TEL voice, TEL guidance) circuit

Audio system sound does not sound.

Refer to 

AV-53, "Symptom Table"

.

Originating sound is not heard 
by the other party with hands-
free phone communication.

Voice recognition function is normal.

TEL adapter unit

Voice recognition function does not work.

Microphone signal circuit.
Refer to 

AV-36, "Diagnosis Procedure"

.

Revision: 2011 October

2012 JUKE

AV-56

< SYMPTOM DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

HANDS-FREE PHONE SYMPTOMS

Symptoms

Possible malfunction location / Action to take

All steering switches are not operated.

Steering switch signal ground circuit. (steering switch to TEL adapter unit)
 Refer to 

AV-44, "Diagnosis Procedure"

.

Only specified switch cannot be operated.

Replace steering switch.

“

 

”, “SEEK UP”, “SEEK DOWN” and “SOURCE” 

switches are not operated.

Steering switch signal A circuit. (steering switch to TEL adapter unit)
Refer to 

AV-40, "Diagnosis Procedure"

.

“

”, “VOL UP” and “VOL DOWN” switches are not oper-

ated.

Steering switch signal B circuit. (steering switch to TEL adapter unit)
Refer to 

AV-42, "Diagnosis Procedure"

.

Revision: 2011 October

2012 JUKE

AV

NORMAL OPERATING CONDITION

AV-57

< SYMPTOM DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

NORMAL OPERATING CONDITION

Description

INFOID:0000000007577927

RELATED TO AUDIO

• The majority of the audio malfunctions are the result of outside causes (bad CD, electromagnetic interfer-

ence, etc.). Check the symptoms below to diagnose the malfunction.

• The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.

Check that noise is caused and/or changed by engine speed, ignition switch turned to each position, and
operation of each piece of electrical equipment. Then determine the cause.

NOTE:
• CD-R is not guaranteed to play because they can contain compressed audio (MP3, WMA) or could be incor-

rectly mastered by the customer on a computer.

• Check that the CDs carry the Compact Disc Logo. If not, the disc is not mastered to the red book Compact

Disc Standard and may not play.

Noise resulting from variations in field strength, such as fading noise and multi-path noise, or external noise from trains and other
sources, is not a malfunction.

NOTE:

• Fading noise: This noise occurs because of variations in the field strength in a narrow range due to mountains or buildings blocking

the signal.

• Multi-path noise: This noise results from a time difference between the broadcast waves directly from the station arriving at the

antenna and the waves reflected by mountains or buildings.

RELATED TO TELEPHONE

Symptoms

Cause and Counter measure

Cannot play

Check that the disc was inserted correctly.

Check that the disc is scratched or dirty.

Check if there is condensation inside the player. If there is, wait until the condensation is gone 
(about 1 hour) before using the player.

If there is a temperature increase error, the CD player will play correctly after it returns to the nor-
mal temperature. 

Files with extensions other than “.MP3”, “.WMA”, “.mp3”, or “.wma” cannot be played. In addition, 
the character codes and number of characters for folder names and file names should be in com-
pliance with the specifications.

Check if the disc or the file is generated in an irregular format. This may occur depending on the 
variation or the setting of MP3/WMA writing applications or other text editing applications.

Check if the finalization process, such as session close and disc close, is done for the disc.

Check if the disc is protected by copyright.

Poor sound quality

Check if the disc is scratched or dirty.

Bit rate may be too low.

It takes a relatively long time before 
the music starts playing.

If there are many folder or file levels on the MP3/WMA CD, or if it is a multisession disc, some 
time may be required before the music starts playing.

Music cuts off or skips

The writing software and hardware combination might not match, or the writing speed, writing 
depth, writing width, etc., might not match the specifications. Try using the slowest writing speed.

Skipping with high bit rate files

Skipping may occur with large quantities of data, such as for high bit rate data.

Move immediately to the next song 
when playing.

When a non-MP3/WMA file has been given an extension of “.MP3”, “.WMA”, “.mp3” or “.wma”, or 
when play is prohibited by copyright protection, there will be approximately 5 seconds of no sound 
and then the player will skip to the next song.

The songs do not play back in the 
desired order.

The playback order is the order in which the files were written by the writing software. Therefore, 
the files might not play in the desired order.

Revision: 2011 October

2012 JUKE

AV-58

< SYMPTOM DIAGNOSIS >

[AUDIO WITHOUT NAVIGATION]

NORMAL OPERATING CONDITION

Symptoms

Cause and Counter measure

System fails to interpret the com-
mand correctly.

1. Ensure that the command format is valid.

2. Ensure that the command is spoken after the tone.

3. Speak clearly without pausing between words and at a level appropriate to the ambient noise 
level in the vehicle.

4. Ensure that the ambient noise level is not excessive (for example, windows open or defroster 
on).
NOTE:
 If it is too noisy to use the phone, it is likely that the voice commands will not be recognized.

5. If more than one command was said at a time, try saying the commands separately.

6. If the system consistently fails to recognize commands, the voice training procedure should be 
carried out to improve the recognition response for the speaker.
Refer to 

AV-15, "On Board Diagnosis Function"

.

The system consistently selects 
the wrong entry from the phone 
book.

1. Ensure that the phone book entry name requested matches what was originally stored. This 
can be confirmed by using the “List Names” command.

2. Replace one of the names being confused with a new name.

Revision: 2011 October

2012 JUKE

AV

AUDIO UNIT

AV-59

< REMOVAL AND INSTALLATION >

[AUDIO WITHOUT NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

REMOVAL AND INSTALLATION

AUDIO UNIT

Removal and Installation

INFOID:0000000007577928

REMOVAL

1.

Remove cluster lid C. Refer to 

IP-11, "Exploded View"

.

2.

Remove audio unit screws.

3.

Disconnect audio unit connectors to remove audio unit and brackets as a single unit.

4.

Remove brackets screws to remove audio unit.

INSTALLATION

Install in the reverse order of removal.

Revision: 2011 October

2012 JUKE

AV-60

< REMOVAL AND INSTALLATION >

[AUDIO WITHOUT NAVIGATION]

FRONT DOOR SPEAKER

FRONT DOOR SPEAKER

Removal and Installation

INFOID:0000000007577929

REMOVAL

1.

Remove front door finisher. Refer to 

INT-12, "Exploded View"

.

2.

Remove front door speaker screws, then disconnect front door speaker connector and remove front door
speaker.

INSTALLATION

Install in the reverse order of removal.

Revision: 2011 October

2012 JUKE