Content .. 689 690 691 692 ..

Nissan Juke (2016 year). Service Repair Manual - part 691

DIAGNOSIS AND REPAIR WORK FLOW

WW-27

< BASIC INSPECTION >

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORK FLOW

Work Flow

INFOID:0000000012197051

OVERALL SEQUENCE

DETAILED FLOW

JMKIA8652GB

Revision: November 2015

2016 JUKE

WW-28

< BASIC INSPECTION >

DIAGNOSIS AND REPAIR WORK FLOW

GET INFORMATION FOR SYMPTOM

1. Get detailed information from the customer about the symptom (the condition and the environment when

the incident/malfunction occurs).

2. Check operation condition of the function that is malfunctioning.

>> GO TO 2.

CHECK DTC

1. Check DTC.

2. Perform the following procedure if DTC is detected.

Record DTC and freeze frame data (Print them out using CONSULT.)

Erase DTC.

Study the relationship between the cause detected by DTC and the symptom described by the customer.

3. Check related service bulletins for information.
Are any symptoms described and any DTC detected?

Symptom is described, DTC is detected>>GO TO 3.

Symptom is described, DTC is not detected>>GO TO 4.

Symptom is not described, DTC is detected>>GO TO 5.

CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

Also study the normal operation and fail-safe related to the symptom.

Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 5.

CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 6.

PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected

again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.

If two or more DTCs are detected, refer to DTC INSPECTION PRIORITY CHART, and determine trouble diag-

nosis order.

NOTE:

• Freeze frame data is useful if the DTC is not detected.

• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service

Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during

this check.

If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-

MATION PROCEDURE.

Is DTC detected?

YES

>> GO TO 7.

>> Check according to

GI-45, "Intermittent Incident"

DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS

Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step

4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?

YES

>> GO TO 7.

>> Monitor input data from related sensors or check voltage of related module terminals using CON-

SULT.

DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE

Revision: November 2015

2016 JUKE

DIAGNOSIS AND REPAIR WORK FLOW

WW-29

< BASIC INSPECTION >

Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?

YES

>> GO TO 8.

>> Check according to

GI-45, "Intermittent Incident"

REPAIR OR REPLACE THE MALFUNCTIONING PART

1. Repair or replace the malfunctioning part.

2. Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-

ment.

3. Check DTC. If DTC is detected, erase it.

>> GO TO 9.

FINAL CHECK

When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the

malfunction is repaired securely.

When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the

symptom is not detected.
Is DTC detected and does symptom remain?

YES-1 >> DTC is detected: GO TO 7.

YES-2 >> Symptom remains: GO TO 4.

>> Before returning the vehicle to the customer, always erase DTC.

Revision: November 2015

2016 JUKE

WW-30

< DTC/CIRCUIT DIAGNOSIS >

WIPER AND WASHER FUSE

DTC/CIRCUIT DIAGNOSIS

WIPER AND WASHER FUSE

Diagnosis Procedure

INFOID:0000000012197052

CHECK FUSES

Check that the following fuses is not blown (open).

Is the inspection result normal?

YES

>> INSPECTION END

>> Replace the fuse with a new one after repairing the applicable circuit.

Unit

Location

No.

Capacity

Front wiper motor

IPDM E/R

30 A

Washer pump

Fuse block (J/B)

10 A

Revision: November 2015

2016 JUKE

FRONT WIPER MOTOR LO CIRCUIT

WW-31

< DTC/CIRCUIT DIAGNOSIS >

FRONT WIPER MOTOR LO CIRCUIT

Component Function Check

INFOID:0000000012197053

CHECK FRONT WIPER LO OPERATION

CONSULT ACTIVE TEST

1. Select “FRONT WIPER” of IPDM E/R active test item.

2. With operating the test item, check front wiper operation.

Is front wiper (LO) operation normally?

YES

>> Front wiper motor LO circuit is normal.

>> Refer to

WW-31, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000012197054

CHECK FRONT WIPER MOTOR (LO) OUTPUT VOLTAGE

1. Turn ignition switch OFF.

2. Disconnect front wiper motor connector.

3. Turn ignition switch ON, and wait for 10 seconds.

4. Check voltage between front wiper motor harness connector and ground.

*: According to front wiper protection function, IPDM E/R supplies voltage for 10 seconds (battery voltage) and

then stops for 20 seconds (0 V). This operations occurs repeatedly.
Is the inspection result normal?

YES

>> Replace front wiper motor.

>> GO TO 2.

CHECK FRONT WIPER MOTOR (LO) CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.

4. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

>> Repair or replace harness.

: Front wiper (LO) operation

Off

: Stop the front wiper.

(+)

(

−

)

Voltage (Approx.)

Front wiper motor

Connector

Terminal

E20

Ground

Battery voltage

(10 seconds*)

IPDM E/R

Front wiper motor

Continuity

Connector

Terminal

Connector

Terminal

E14

E20

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E14

Not existed

Revision: November 2015

2016 JUKE

WW-32

< DTC/CIRCUIT DIAGNOSIS >

FRONT WIPER MOTOR HI CIRCUIT

FRONT WIPER MOTOR HI CIRCUIT

Component Function Check

INFOID:0000000012197055

CHECK FRONT WIPER HI OPERATION

CONSULT ACTIVE TEST

1. Select “FRONT WIPER” of IPDM E/R active test item.

2. With operating the test item, check front wiper operation.

Is front wiper (HI) operation normally?

YES

>> Front wiper motor HI circuit is normal.

>> Refer to

WW-32, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000012197056

CHECK FRONT WIPER MOTOR (HI) OUTPUT VOLTAGE

CONSULT ACTIVE TEST

1. Turn ignition switch OFF.

2. Disconnect front wiper motor connector.

3. Turn ignition switch ON.

4. Select “FRONT WIPER” of IPDM E/R active test item.

5. With operating the test item, check voltage between front wiper motor harness connector and ground.

*: According to front wiper protection function, IPDM E/R supplies voltage for 10 seconds (battery voltage) and

then stops for 20 seconds (0 V). This operations occurs repeatedly.
Is the inspection result normal?

YES

>> Replace front wiper motor.

>> GO TO 2.

CHECK FRONT WIPER MOTOR (HI) CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.

4. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

>> Repair or replace harness.

: Front wiper (HI) operation

Off

: Stop the front wiper.

(+)

(

−

)

Condition

Voltage (Approx.)

Front wiper motor

Connector

Terminal

E20

Ground

FRONT WIPER

Battery voltage

(10 seconds*)

IPDM E/R

Front wiper motor

Continuity

Connector

Terminal

Connector

Terminal

E14

E20

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E14

Not existed

Revision: November 2015

2016 JUKE

FRONT WIPER STOP POSITION SIGNAL CIRCUIT

WW-33

< DTC/CIRCUIT DIAGNOSIS >

FRONT WIPER STOP POSITION SIGNAL CIRCUIT

Component Function Check

INFOID:0000000012197057

CHECK FRONT WIPER STOP POSITION SIGNAL

CONSULT DATA MONITOR

1. Select “WIP AUTO STOP” of IPDM E/R data monitor item.

2. Operate the front wiper.

3. With the front wiper operation, check the monitor status.

Is the status of item normal?

YES

>> Front wiper stop position signal circuit is normal.

>> Refer to

WW-33, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000012197058

CHECK IPDM E/R OUTPUT VOLTAGE

1. Turn ignition switch OFF.

2. Disconnect front wiper motor connector.

3. Turn ignition switch ON.

4. Check voltage between front wiper motor harness connector and ground.

Is the inspection result normal?

YES

>> Replace front wiper motor.

>> GO TO 2.

CHECK FRONT WIPER MOTOR CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.

4. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

>> Repair or replace harness.

Monitor item

Condition

Monitor status

WIP AUTO STOP

Front wiper motor

Stop position

STOP P

Except stop position

ACT P

(+)

(

−

)

Voltage (Approx.)

Front wiper motor

Connector

Terminal

E20

Ground

Battery voltage

IPDM E/R

Front wiper motor

Continuity

Connector

Terminal

Connector

Terminal

E13

E20

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E13

Not existed

Revision: November 2015

2016 JUKE

WW-34

< DTC/CIRCUIT DIAGNOSIS >

FRONT WIPER MOTOR GROUND CIRCUIT

FRONT WIPER MOTOR GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000012197059

CHECK FRONT WIPER MOTOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect front wiper motor connector.

3. Check continuity between front wiper motor harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

>> Repair or replace harness.

Front wiper motor

Ground

Continuity

Connector

Terminal

E20

Existed

Revision: November 2015

2016 JUKE

Content .. 689 690 691 692 ..