Content .. 657 658 659 660 ..

Nissan Juke (2016 year). Service Repair Manual - part 659

TM-464

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A

Is it necessary to erase permanent DTC?

YES

>> GO TO 3.

>> GO TO 7.

CHECK DTC (ECM AND TCM)

Check the DTC.
Is any DTC other than “P0711” detected?

YES

>> Check DTC detected item. Refer to

EC-706, "DTC Index"

(ECM),

TM-414, "DTC Index"

(TCM).

>> GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE (PART 1)

TESTING CONDITION:

•

While performing the following procedure, do not add fuel.

•

Before performing the following procedure, check that fuel level is between 1/4 and 4/4.

•

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

With CONSULT

1. Move the vehicle to a cool place.

NOTE:

Cool the vehicle in an environment of ambient air temperature between

−

C (14

F) and 35

C (95

F).

2. Turn ignition switch OFF and leave the vehicle for 12 hours.

CAUTION:

Never turn ignition switch ON during this procedure.

NOTE:

The vehicle must be cooled with the food open.

3. Turn ignition switch ON.

CAUTION:

Never start the engine.

4. Select “Data Monitor” in “TRANSMISSION”.

5. Select “FLUID TEMP”.

6. Record CVT fluid temperature.

7. Start engine and let it idle for 5 minutes or more.

CAUTION:

Never turn ignition switch OFF during idling.

8. Check 1st trip DTC.

With GST

1. Move the vehicle to a cool place.

NOTE:

Cool the vehicle in an environment of ambient air temperature between

−

C (14

F) and 35

C (95

F).

2. Turn ignition switch OFF and leave the vehicle for 12 hours.

CAUTION:

Never turn ignition switch ON during this procedure.

NOTE:

The vehicle must be cooled with the food open.

3. Start engine and let it idle for 5 minutes or more.

CAUTION:

Never turn ignition switch OFF during idling.

4. Check 1st trip DTC.
Is “P0711” detected?

YES

>> Go to

TM-466, "Diagnosis Procedure"

NO-1 (With CONSULT)>>GO TO 5.

NO-2 (With GST)>>GO TO 6.

CHECK CVT FLUID TEMPERATURE

With CONSULT

1. Select “Data Monitor” in “TRANSMISSION”.

2. Select “FLUID TEMP”.
Is the value of “FLUID TEMP” 10

C (50

F) or more?

YES

>> INSPECTION END

>> GO TO 6.

Revision: November 2015

2016 JUKE

P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A

TM-465

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

PERFORM DTC CONFIRMATION PROCEDURE (PART 2)

With CONSULT

1. Drive the vehicle for the total minutes specified in the Driving time column below with the following condi-

tions satisfied.

2. Stop the vehicle.

3. Check the first trip DTC.

With GST

1. Drive the vehicle and maintain the following conditions for 20 minutes or more.

2. Stop the vehicle.

3. Check the first trip DTC.
Is “P0711” detected?

YES

>> Go to

TM-466, "Diagnosis Procedure"

NO-1 >> To check malfunction symptom before repair: Refer to

GI-45, "Intermittent Incident"

NO-2 >> Confirmation after repair: INSPECTION END

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Turn ignition switch OFF and cool the engine.

2. Turn ignition switch ON.

CAUTION:

Never start the engine.

3. Select “Data Monitor” in “TRANSMISSION”.

4. Select “FLUID TEMP”.

5. Record CVT fluid temperature.

6. Start the engine and wait for at least 2 minutes.

7. Drive the vehicle for the total minutes specified in the Driving time column below with the following condi-

tions satisfied.

Selector lever

: “D” position

Accelerator pedal position

: 1.0/8 or more

Vehicle speed

: 10 km/h (7 MPH) or more

CVT fluid temperature before engine start

Driving time

−

C (

−

F) –

−

C (

−

23.8

20 minutes or more

−

C (

−

F) –

−

C (

−

5.8

18 minutes or more

−

C (

−

F) –

−

C (

−

12.2

14 minutes or more

−

C (14

F) –

−

C (30.2

10 minutes or more

C (32

F) – 9

C (48.2

7 minutes or more

Selector lever

: “D” position

Accelerator pedal position

: 1.0/8 or more

Vehicle speed

: 10 km/h (7 MPH) or more

Selector lever

: “D” position

Accelerator pedal position

: 1.0/8 or more

Vehicle speed

: 10 km/h (7 MPH) or more

CVT fluid temperature before engine start

Driving time

−

C (

−

F) –

−

C (

−

23.8

20 minutes or more

−

C (

−

F) –

−

C (

−

5.8

18 minutes or more

−

C (

−

F) –

−

C (

−

12.2

14 minutes or more

−

C (14

F) –

−

C (30.2

10 minutes or more

Revision: November 2015

2016 JUKE

TM-466

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A

8. Stop the vehicle.

9. Check the first trip DTC.

With GST

1. Turn ignition switch OFF and cool the engine.

2. Start the engine and wait for at least 2 minutes.

3. Drive the vehicle and maintain the following conditions for 20 minutes or more.

4. Stop the vehicle.

CAUTION:

Never turn ignition switch OFF

5. Check the first trip DTC.
Is “P0711” detected?

YES

>> Go to

TM-466, "Diagnosis Procedure"

>> GO TO 8.

CHECK CVT FLUID TEMPERATURE SENSOR

1. Turn ignition switch OFF.

2. Disconnect CVT unit connector.

3. Check resistance between CVT unit connector terminals.

Is the inspection result normal?

YES-1 >> To check malfunction symptom before repair: Refer to

GI-45, "Intermittent Incident"

YES-2 >> Confirmation after repair: INSPECTION END

>> There is a malfunction of CVT fluid temperature sensor. Replace transaxle assembly. Refer to

TM-577, "Removal and Installation"

Diagnosis Procedure

INFOID:0000000012201167

CHECK CVT FLUID TEMPERATURE SENSOR

1. Turn ignition switch OFF.

2. Disconnect CVT unit connector.

3. Check resistance between CVT unit connector terminals.

Is the inspection result normal?

YES

>> GO TO 2.

>> GO TO 4.

C (32

F) – 9

C (48.2

7 minutes or more

Other than the above

— (Go to “8.CHECK CVT FLU-
ID TEMPERATURE SENSOR”)

Selector lever

: “D” position

Accelerator pedal position

: 1.0/8 or more

Vehicle speed

: 10 km/h (7 MPH) or more

CVT fluid temperature before engine start

Driving time

CVT unit

Condition

Resistance

(Approx.)

Terminal

12 – 18

CVT fluid temperature: 20

C (68

6.5 k

Ω

CVT fluid temperature: 50

C (122

2.2 k

Ω

CVT fluid temperature: 80

C (176

0.87 k

Ω

CVT unit

Condition

Resistance

(Approx.)

Connector

Terminal

F250

12 – 18

CVT fluid temperature: 20

C (68

6.5 k

Ω

CVT fluid temperature: 50

C (122

2.2 k

Ω

CVT fluid temperature: 80

C (176

0.87 k

Ω

Revision: November 2015

2016 JUKE

P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A

TM-467

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 1)

1. Disconnect the TCM connector.

2. Check continuity between TCM harness connector terminals and CVT unit harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace damaged parts.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 2)

Check continuity between TCM harness connector terminals and ground.

Is the inspection result normal?

YES

>> INSPECTION END

>> Repair or replace damaged parts.

CHECK DTC (TCM)

With CONSULT

1. Perform “DTC CONFIRMATION PROCEDURE”. Refer to

TM-463, "DTC Description"

2. Select “Self Diagnostic Results” in “TRANSMISSION”.
Is “P0711” detected?

YES

>> There is a malfunction of the CVT fluid temperature sensor. Replace the transaxle assembly.

Refer to

TM-577, "Removal and Installation"

>> INSPECTION END

TCM

CVT unit

Continuity

Connector

Terminal

Connector

Terminal

F83

F82

Existed

TCM

—

Continuity

Connector

Terminal

F83

Ground

Not existed

Revision: November 2015

2016 JUKE

TM-468

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A

P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A

DTC Logic

INFOID:0000000012201168

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine and wait for 10 seconds or more.

2. Check the first trip DTC.
Is “P0712” detected?

YES

>> Go to

TM-468, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012201169

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT

1. Turn ignition switch OFF.

2. Disconnect TCM connector and CVT unit connector.

3. Check continuity between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace malfunctioning part.

CHECK CVT UNIT TERMINAL CODE ASSEMBLY

Check continuity between CVT unit connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> There is a malfunction of the CVT unit terminal code assembly. Replace the transaxle assembly.

Refer to

TM-577, "Removal and Installation"

CHECK CVT FLUID TEMPERATURE SENSOR

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P0712

FLUID TEMP SENSOR A
(Transmission Fluid Tempera-
ture Sensor A Circuit Low)

When all of the following conditions are satis-
fied and this state is maintained for 5 seconds:
• TCM power supply voltage: More than 11 V
• Fluid temperature sensor detection voltage:

0.15 V or less

• Harness or connector

(CVT fluid temperature sensor circuit is
shorted to ground)

• CVT fluid temperature sensor

TCM

—

Continuity

Connector

Terminal

F83

Ground

Not existed

CVT unit

—

Continuity

Connector

Terminal

F82

Ground

Not existed

Revision: November 2015

2016 JUKE

P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A

TM-469

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

Check resistance between CVT unit connector terminals.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> There is a malfunction of the CVT fluid temperature sensor. Replace the transaxle assembly.

Refer to

TM-577, "Removal and Installation"

CVT unit

Condition

Resistance

(Approx.)

Connector

Terminal

F250

12 – 18

CVT fluid temperature: 20

C (68

6.5 k

Ω

CVT fluid temperature: 50

C (122

2.2 k

Ω

CVT fluid temperature: 80

C (176

0.87 k

Ω

Revision: November 2015

2016 JUKE

TM-470

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A

P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A

DTC Logic

INFOID:0000000012201170

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start the engine.

2. Maintain the following condition for 10 seconds or more.

3. Stop the vehicle.

4. Check the first trip DTC.
Is “P0713” detected?

YES

>> Go to

TM-470, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012201171

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector and CVT unit connector.

3. Check continuity between TCM harness connector terminals and CVT unit harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace malfunctioning parts.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 2)

1. Turn ignition switch ON.

2. Check voltage between TCM harness connector terminal and ground.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P0713

FLUID TEMP SENSOR A
(Transmission Fluid Tempera-
ture Sensor A Circuit High)

When all of the following conditions are satis-
fied and this state is maintained for 5 seconds:
• TCM power supply voltage: More than 11 V
• Vehicle speed: More than 10 km/h (7 MPH)
• Fluid temperature sensor detection voltage:

2.48 V or more

• Harness or connector

(CVT fluid temperature sensor circuit is
open or shorted to power supply)

• CVT fluid temperature sensor

Vehicle speed

: 20 km/h (12 MPH) or more

TCM

CVT unit

Continuity

Connector

Terminal

Connector

Terminal

F83

F82

Existed

Revision: November 2015

2016 JUKE

P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A

TM-471

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace malfunctioning parts.

CHECK CVT FLUID TEMPERATURE SENSOR

1. Turn ignition switch OFF.

2. Check resistance between CVT unit connector terminals.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> There is a malfunction of the CVT fluid temperature sensor. Replace the transaxle assembly.

Refer to

TM-577, "Removal and Installation"

−

Voltage

(Approx.)

TCM

Connector

Terminal

F83

Ground

0 V

CVT unit

Condition

Resistance

(Approx.)

Connector

Terminal

F250

12 – 18

CVT fluid temperature: 20

C (68

6.5 k

Ω

CVT fluid temperature: 50

C (122

2.2 k

Ω

CVT fluid temperature: 80

C (176

0.87 k

Ω

Revision: November 2015

2016 JUKE

Content .. 657 658 659 660 ..