Nissan Juke (2016 year). Service Repair Manual - part 496

SQUEAK AND RATTLE TROUBLE DIAGNOSES

MIR-13

< SYMPTOM DIAGNOSIS >

MIR

1. Trunk lid dumpers out of adjustment
2. Trunk lid striker out of adjustment
3. Trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing, or insulating the item(s) or component(s) caus-

ing the noise.

SUNROOF/HEADLINING

Noises in the sunroof / headlining area can often be traced to one of the following items:
1. Sunroof lid, rail, linkage, or seals making a rattle or light knocking noise
2. Sunvisor shaft shaking in the holder
3. Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these

incidents. Repairs usually consist of insulating with felt cloth tape.

SEATS

When isolating seat noise it is important to note the position the seat is in and the load placed on the seat

when the noise occurs. These conditions should be duplicated when verifying and isolating the cause of the

noise.

Causes of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-

ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component

or applying urethane tape to the contact area.

UNDERHOOD

Some interior noise may be caused by components under the hood or on the engine wall. The noise is then

transmitted into the passenger compartment.

Causes of transmitted underhood noise include:
1. Any component mounted to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator mounting pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best

method is to secure, move, or insulate one component at a time and test drive the vehicle. Also, engine RPM

or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or

insulating the component causing the noise.

Revision: November 2015

2016 JUKE

MIR-14

< SYMPTOM DIAGNOSIS >

SQUEAK AND RATTLE TROUBLE DIAGNOSES

Diagnostic Worksheet

INFOID:0000000012201506

PIIB8740E

Revision: November 2015

2016 JUKE

SQUEAK AND RATTLE TROUBLE DIAGNOSES

MIR-15

< SYMPTOM DIAGNOSIS >

MIR

PIIB8742E

Revision: November 2015

2016 JUKE

MIR-16

< REMOVAL AND INSTALLATION >

INSIDE MIRROR

REMOVAL AND INSTALLATION

INSIDE MIRROR

Exploded View

INFOID:0000000012201507

Removal and Installation

INFOID:0000000012201508

CAUTION:

Never reuse the inside mirror assembly disassembled from mirror base.

REMOVAL

Slide the inside mirror assembly upward to remove.

NOTE:

Insert flat-bladed screwdriver (A) under the inside mirror (1).

Slide the inside mirror to the upper side while pushing the pawl

downward.

CAUTION:

Never use excessive force to remove the inside mirror because

it is inserted tightly into the mirror base.

INSTALLATION

Install in the reverse order of removal.

Windshield glass

Mirror base

Inside mirror assembly

: Always replace after every disassembly.

JMLIA0400ZZ

: Always replace after every disassembly.

JMLIA0055ZZ

Revision: November 2015

2016 JUKE

OUTSIDE MIRROR

MIR-17

< REMOVAL AND INSTALLATION >

MIR

OUTSIDE MIRROR

Exploded View

INFOID:0000000012201509

DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Removal and Installation

INFOID:0000000012201510

CAUTION:

When removing, always use a remover tool that is made of plastic.

REMOVAL

Door mirror cover

Side turn signal lamp

Door mirror finisher
(without around view monitor sys-
tem)

Door mirror actuator

Glass mirror

Door mirror corner cover

Door mirror housing

Side camera assembly
(with around view monitor system)

Side camera finisher
(with around view monitor system)

: Clip

: Pawl

N·m (kg-m, in-lb)

JMLIA6142GB

Revision: November 2015

2016 JUKE

MIR-18

< REMOVAL AND INSTALLATION >

OUTSIDE MIRROR

1. Disengage door mirror corner cover fixing clips using a remover

tool (A), and then remove door mirror corner cover.

2. Remove front door finisher. Refer to

INT-13, "Removal and Installation"

3. Disconnect door mirror harness connector.
4. Remove door mirror mounting nuts, and then remove door mirror assembly.

INSTALLATION

Install in the reverse order of removal.

DOOR MIRROR ASSEMBLY : Disassembly and Assembly

INFOID:0000000012201511

DISASSEMBLY

1. Remove door mirror assembly. Refer to

MIR-17, "DOOR MIRROR ASSEMBLY : Removal and Installa-

tion"

2. Remove glass mirror. Refer to

MIR-19, "GLASS MIRROR : Removal and Installation"

3. Remove door mirror actuator mounting bolts (A), and disconnect

harness connector (B), and then remove door mirror actuator.

4. Disengage door mirror cover and door mirror finisher (without around view monitor system) or side cam-

era finisher (with around view monitor system). Refer to

MIR-20, "DOOR MIRROR COVER : Removal and

Installation"

5. Disconnect side camera harness connector (with around view monitor system).
6. Remove side camera bracket fixing screws (A), and then

remove side camera assembly from door mirror finisher. (with

around view monitor system)

7. Remove side turn signal lamp. Refer to the following.

• Xenon type: Refer to

EXL-104, "Removal and Installation"

• Halogen type: Refer to

EXL-215, "Removal and Installation"

ASSEMBLY

Note the following item, and then assemble in the reverse order of disassembly.

: Clip

JMLIA1391ZZ

JMLIA5685ZZ

JMLIA5689ZZ

Revision: November 2015

2016 JUKE

OUTSIDE MIRROR

MIR-19

< REMOVAL AND INSTALLATION >

MIR

CAUTION:

Perform side camera image calibration (with side camera). Refer to

AV-116, "CALIBRATING CAMERA

IMAGE (AROUND VIEW MONITOR) : Description"

GLASS MIRROR
GLASS MIRROR : Removal and Installation

INFOID:0000000012201512

REMOVAL

1. Place the glass mirror inward.
2. Apply protective tape (A) on door mirror housing and glass mir-

ror to protect it from damage.

3. Insert remover tool (A) into the recess at outside between glass mirror and door mirror actuator, and then

disengage the door mirror fixing pawls.

CAUTION:

Remove the pawls slowly so they are not damaged.

NOTE:

Insert remover tool into recesses,and push up while rotating (twisting) to make work easier.

4. Disconnect heater mirror terminals (A). (with heater mirror)

CAUTION:

Make a mark (short note, photo, etc.) of terminals layout,

before disassembly.

5. Remove glass mirror.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

After installation, visually check that pawls are securely engaged.

JMLIA5703ZZ

JMLIA5704ZZ

JMLIA4194ZZ

Revision: November 2015

2016 JUKE

MIR-20

< REMOVAL AND INSTALLATION >

OUTSIDE MIRROR

DOOR MIRROR COVER
DOOR MIRROR COVER : Removal and Installation

INFOID:0000000012201513

REMOVAL

1. Remove the glass mirror. Refer to

MIR-19, "GLASS MIRROR : Removal and Installation"

2. Remove door mirror finisher (without around view monitor sys-

tem) or side camera finisher (with around view monitor system)

fixing screws (A), disengage door mirror cover and door mirror

finisher (without around view monitor system) or side camera

finisher (with around view monitor system) fixing pawls pushed

in the direction of the arrows as shown in figure.

3. Disengage door mirror cover fixing pawls, and then remove door

mirror cover (1) and door mirror finisher (without around view

monitor system) or side camera finisher (with around view moni-

tor system) (2).

4. Disconnect side camera harness connector. (with around view monitor system)

5. Disengage door mirror cover fixing pawls, remove door mirror

cover (1) from door mirror finisher (without around view monitor

system) or side camera finisher (with around view monitor sys-

tem) (2) indicated by arrows as shown in the figure.

INSTALLATION

Note the following item and then install in the reverse order of removal.

CAUTION:

After installation, visually check that pawls are securely engaged.

JMLIA5686ZZ

: Pawl

JMLIA5687ZZ

JMLIA5688ZZ

Revision: November 2015

2016 JUKE

Content .. 494 495 496 497 ..