Content .. 409 410 411 412 ..

Nissan Juke (2016 year). Service Repair Manual - part 411

CONSULT/GST CHECKING SYSTEM

GI-59

< BASIC INSPECTION >

JRAWC2862GB

Revision: November 2015

2016 JUKE

GI-60

< BASIC INSPECTION >

CONSULT/GST CHECKING SYSTEM

JRAWC2863GB

Revision: November 2015

2016 JUKE

CONSULT/GST CHECKING SYSTEM

GI-61

< BASIC INSPECTION >

JRAWC2864GB

Revision: November 2015

2016 JUKE

GI-62

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Re-
quired Procedure After Battery Disconnection

INFOID:0000000012196808

*: Not equipped.

SYSTEM

ITEM

REFERENCE

Automatic air conditioning sys-
tem

Temperature setting trimmer

HAC-50, "Temperature Setting Trimmer"

Foot position setting trimmer

HAC-51, "Foot Position Setting Trimmer"

Inlet port memory function*

—

Inlet port memory function (FRE)

HAC-51, "Inlet Port Memory Function (FRE)"

Inlet port memory function (REC)

HAC-50, "Inlet Port Memory Function (REC)"

Gas sensor sensitivity adjustment function*

—

Auto intake switch interlocking movement change*

—

Clean switch interlocking movement change*

—

Automatic drive positioner*

Automatic drive positioner system

—

Power window control

Power window control system

PWC-24, "Description"

Sunroof system

RF-17, "ADDITIONAL SERVICE WHEN RE-

PLACING CONTROL UNIT : Description"

Sunshade system

RF-17, "ADDITIONAL SERVICE WHEN RE-

PLACING CONTROL UNIT : Description"

Rear view monitor*

Rear view monitor predictive course line center po-
sition adjustment

—

Around view monitor*

Predictive course line center position adjustment

—

Automatic back door system*

Automatic back door system

—

Engine oil level read*

Engine oil level read

—

Revision: November 2015

2016 JUKE

GW-1

BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY

SECTION

CONTENTS

GLASS & WINDOW SYSTEM

PRECAUTION ...............................................

PRECAUTIONS ...................................................

Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

Precaution for Procedure without Cowl Top Cover

......

Precautions for Removing Battery Terminal .............

Handling for Adhesive and Primer ............................

PREPARATION ............................................

PREPARATION ...................................................

Special Service Tools ..............................................

Commercial Service Tools .......................................

SYMPTOM DIAGNOSIS ...............................

SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ................................................................

Work Flow .................................................................

Inspection Procedure ................................................

Diagnostic Worksheet ...............................................

REMOVAL AND INSTALLATION ...............

WINDSHIELD GLASS ........................................

Exploded View ........................................................

Removal and Installation .........................................

Inspection ................................................................

BACK DOOR WINDOW GLASS ......................

Exploded View .........................................................

Removal and Installation .........................................

Inspection ................................................................

FRONT DOOR GLASS .....................................

Exploded View .........................................................

Removal and Installation .........................................

Inspection and Adjustment ......................................

FRONT REGULATOR .......................................

Exploded View .........................................................

Removal and Installation .........................................

Disassembly and Assembly .....................................

Inspection and Adjustment ......................................

REAR DOOR GLASS .......................................

Exploded View .........................................................

Removal and Installation .........................................

Inspection and Adjustment ......................................

REAR REGULATOR .........................................

Exploded View .........................................................

Removal and Installation .........................................

Disassembly and Assembly .....................................

Inspection and Adjustment ......................................

Revision: November 2015

2016 JUKE

GW-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000012199879

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along

with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain

types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS

system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front

air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this

Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, it is recommended that all maintenance

and repair be performed by an authorized NISSAN/INFINITI dealer.

• Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury

caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module,

see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness

connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.

• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with

a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing

serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery or batteries, and wait at least 3 minutes before performing any service.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000012199880

When performing the procedure after removing cowl top cover, cover

the lower end of windshield with urethane, etc to prevent damage to

windshield.

Precautions for Removing Battery Terminal

INFOID:0000000012996954

When disconnecting the battery terminal, pay attention to the following.

• Always use a 12V battery as power source.

• Never disconnect battery terminal while engine is running.

PIIB3706J

Revision: November 2015

2016 JUKE

PRECAUTIONS

GW-3

< PRECAUTION >

• When removing the 12V battery terminal, turn OFF the ignition

switch and wait at least 30 seconds.

• For vehicles with the engine listed below, remove the battery termi-

nal after a lapse of the specified time:

NOTE:

ECU may be active for several tens of seconds after the ignition switch is turned OFF. If the battery terminal

is removed before ECU stops, then a DTC detection error or ECU data corruption may occur.

• After high-load driving, if the vehicle is equipped with the V9X engine, turn the ignition switch OFF and wait

for at least 15 minutes to remove the battery terminal.

NOTE:

• Turbocharger cooling pump may operate in a few minutes after the ignition switch is turned OFF.

• Example of high-load driving

- Driving for 30 minutes or more at 140 km/h (86 MPH) or more.

- Driving for 30 minutes or more on a steep slope.

• For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON

the ignition switch.

NOTE:

If the ignition switch is turned ON with any one of the terminals of main battery and sub battery discon-

nected, then DTC may be detected.

• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.

NOTE:

The removal of 12V battery may cause a DTC detection error.

Handling for Adhesive and Primer

INFOID:0000000012199882

• Never use an adhesive that is past its usable date. Shelf life of this product is limited to six months after the

date of manufacture. Carefully adhere to the expiration or manufacture date printed on the box.

• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.

• Open the seal of the primer and adhesive just before application. Discard the remainder.

• Before application, be sure to shake the primer container to stir the contents. If any floating material is found,

do not use it.

• If any primer or adhesive contacts the skin, wipe it off with gasoline or an equivalent and wash the skin with

soap.

• When using primer and adhesive, always observe the precautions in the instruction manual.

D4D engine

: 20 minutes

YS23DDT

: 4 minutes

HRA2DDT

: 12 minutes

YS23DDTT

: 4 minutes

K9K engine

: 4 minutes

ZD30DDTi

: 60 seconds

M9R engine

: 4 minutes

ZD30DDTT

: 60 seconds

R9M engine

: 4 minutes

V9X engine

: 4 minutes

YD25DDTi

: 2 minutes

SEF289H

Revision: November 2015

2016 JUKE

GW-4

< PREPARATION >

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000012199883

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tools

INFOID:0000000012199884

Tool number

(Kent-Moore No.)

Tool name

Description

(J-39570)
Chassis ear

Locates the noise

(J-50397)
NISSAN Squeak and Rat-
tle Kit

Repairs the cause of noise

SIIA0993E

SIIA0994E

Tool name

Description

Engine ear

Locates the noise

Suction lifter

Holds the windshield glass, front door glass,
rear door glass and back door window glass

Remover tools

Removes the clips, pawls and metal clips

SIIA0995E

PIIB1805J

JMKIA3050ZZ

Revision: November 2015

2016 JUKE

Content .. 409 410 411 412 ..