Nissan Juke (2016 year). Service Repair Manual - part 381

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     379      380      381      382     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 381

 

 

DOOR OUTSIDE MOLDING

EXT-41

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

DOOR OUTSIDE MOLDING

Exploded View

INFOID:0000000012199329

FRONT DOOR OUTSIDE MOLDING
FRONT DOOR OUTSIDE MOLDING : Removal and Installation

INFOID:0000000012199330

REMOVAL

1. Fully open front door glass.
2. Twist door outside molding toward the outside of the vehicle,

and then lift up and remove it while disengaging the pawls.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

1.

Front door panel

2.

Front door outside molding

3.

Rear door panel

4.

Rear door outside molding

5.

Door glass

: Pawl

JMKIA5664GB

: Pawl

JMKIA5801ZZ

Revision: November 2015

2016 JUKE

EXT-42

< REMOVAL AND INSTALLATION >

DOOR OUTSIDE MOLDING

CAUTION:

When installing front door outside molding, check that pawl (1)

is accurately aligned with mounting hole (2), then press in.

REAR DOOR OUTSIDE MOLDING
REAR DOOR OUTSIDE MOLDING : Removal and Installation

INFOID:0000000012199331

REMOVAL

1. Fully open rear door glass.
2. Twist rear door outside molding toward vehicle outside and

remove molding while disengaging it from door panel.

3. Slide rear door outside molding (1) toward vehicle front, and

then pull molding out from rear door handle (2).

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

When installing rear door outside molding, check that pawl (1)

is accurately aligned with mounting hole (2), then press in.

JMKIA5669ZZ

: Pawl

JMKIA5696ZZ

JMKIA5697ZZ

JMKIA5698ZZ

Revision: November 2015

2016 JUKE

DOOR SASH TAPE

EXT-43

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

DOOR SASH TAPE

Exploded View

INFOID:0000000012199332

FRONT DOOR SASH TAPE
FRONT DOOR SASH TAPE : Removal and Installation

INFOID:0000000012199333

REMOVAL

1. Remove front door outside molding. Refer to 

EXT-41, "FRONT DOOR OUTSIDE MOLDING : Removal

and Installation"

.

2. Heat front door sash tape surface using a dryer, and then peel front door sash tape.

CAUTION:

Never damage painted surface of door panel.

INSTALLATION

NOTE:

For installation position of front door sash tape, refer to the position as shown in the figure.

1.

Front door panel

2.

Front door sash tape

3.

Rear door sash tape

4.

Rear door panel

: Always replace after every disassembly.

JMKIA5665ZZ

Revision: November 2015

2016 JUKE

EXT-44

< REMOVAL AND INSTALLATION >

DOOR SASH TAPE

CAUTION:

• Degrease front door panel mounting surface for front door sash tape.

• Paint grain or dust on mounting surface of front door sash tape may spoil exterior appearance if it

remains. Clean the mounting surface and check that no paint grain or dust remains, before starting

the operation.

• Never reuse front door sash tape.

1. Affix front door sash tape align front door sash tape upper portion to front door outer upper end.

1.

Front door panel

2.

Front door sash tape

3.

Rear door panel

R. Radius

: Always replace after every disassembly.

D

: 2.0 mm (0.08 in) 

E

: 4.0 mm (0.16 in)

JMKIA5666ZZ

Revision: November 2015

2016 JUKE

DOOR SASH TAPE

EXT-45

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

2. Affix front door sash tape (2) to front door panel (3) by applying pressure using a squeegee (A) while peel-

ing off release coated paper (1).

NOTE:

• Peel release coated paper at distance of 10 – 20 mm (0.394 – 0.787 in) ahead (B) of squeegee and affix

front door sash tape.

• To prevent any bubbles from forming, slightly lift the portion, not yet affixed using squeegee, so that por-

tion dose not contact with panel surface. Apply pressure and affix at a low and constant speed using

squeegee tilted at 40 – 50

°

 angle (pushing direction) (C) 30 – 45

°

 angle (pulling direction) (D).

3. For small radius portion of hemming part, gradually apply pres-

sure and affix front door sash tape (1) using squeegee (A) in 1 –

3 steps.

CAUTION:

Never wash the vehicle within 24 hours so as to keep adhe-

sive.

REAR DOOR SASH TAPE
REAR DOOR SASH TAPE : Removal and Installation

INFOID:0000000012199334

REMOVAL

1. Remove rear door outside molding. Refer to 

EXT-42, "REAR DOOR OUTSIDE MOLDING : Removal and

Installation"

.

2. Heat rear door sash tape surface using a dryer, and then peel rear door sash tape.

CAUTION:

Never damage painted surface of door panel.

INSTALLATION

NOTE:

For installation position of rear door sash tape, refer to the position as shown in the figure.

JMKIB1013GB

JMKIB1014ZZ

Revision: November 2015

2016 JUKE

EXT-46

< REMOVAL AND INSTALLATION >

DOOR SASH TAPE

CAUTION:

• Degrease rear door panel mounting surface for rear door sash tape.

• Paint grain or dust on mounting surface of rear door sash tape may spoil exterior appearance if it

remains. Clean the mounting surface and check that no paint grain or dust remains, before starting

the operation.

• Never reuse rear door sash tape.

1. Affix rear door sash tape align rear door sash tape upper portion to rear door outer upper end.

1.

Rear door panel

2.

Rear door sash tape

3.

Front door panel

R. Radius

: Always replace after every disassembly.

D

: 2.0 mm (0.08 in)

JMKIA5667ZZ

Revision: November 2015

2016 JUKE

DOOR SASH TAPE

EXT-47

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

2. Affix rear door sash tape (2) to rear door panel (3) by applying pressure using a squeegee (A) while peel-

ing off release coated paper (1).

NOTE:

• Peel release coated paper at distance of 10 – 20 mm (0.394 – 0.787 in) ahead (B) of squeegee and affix

rear door sash tape.

• To prevent any bubbles from forming, slightly lift the portion, not yet affixed using squeegee, so that por-

tion dose not contact with panel surface. Apply pressure and affix at a low and constant speed using

squeegee tilted at 40 – 50

°

 angle (pushing direction) (C) 30 – 45

°

 angle (pulling direction) (D).

3. For small radius portion of hemming part, gradually apply pres-

sure and affix rear door sash tape (1) using squeegee (A) in 1 –

3 steps.

CAUTION:

Never wash the vehicle within 24 hours so as to keep adhe-

sive.

JMKIB1013GB

JMKIB1014ZZ

Revision: November 2015

2016 JUKE

EXT-48

< REMOVAL AND INSTALLATION >

REAR FENDER COVER

REAR FENDER COVER

Exploded View

INFOID:0000000012199335

Removal and Installation

INFOID:0000000012199336

REMOVAL

Disengage rear fender cover fixing clips using a remover tool (A),

and then remove rear fender cover.

CAUTION:

Apply protective tape (B) to the body side to protect from dam-

age.

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:

When installing rear fender cover, check that clips are securely fitted in body panel holes, and then

press them it.

JMKIB4682ZZ

1.

Rear fender cover

2.

Clip

3.

Seal packing

4.

Rear fender

: Always replace after every disassembly.

: Clip

JMKIA5668ZZ

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     379      380      381      382     ..