Nissan Juke (2016 year). Service Repair Manual - part 368

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     366      367      368      369     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 368

 

 

EXL-166

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

HEADLAMP (LO) CIRCUIT

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK HEADLAMP (LO) GROUND CIRCUIT

Check continuity between headlamp harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK HEADLAMP (LO) BULB

Check the applicable headlamp (LO) bulb.
Is the inspection result normal?

YES

>> Check the corresponding headlamp (LO) harness. Repair or replace if necessary.

NO

>> Replace the corresponding headlamp (LO) bulb. Refer to 

EXL-207, "Replacement"

.

IPDM E/R

Headlamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E15

52

E55

4

Existed

LH

51

E54

Headlamp

—

Continuity

Connector

Terminal

RH

E55

2

Ground

Existed

LH

E54

Revision: November 2015

2016 JUKE

PARKING LAMP CIRCUIT

EXL-167

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

PARKING LAMP CIRCUIT

Component Function Check

INFOID:0000000012201746

1.

CHECK TAIL LAMP OPERATION

Check that the tail lamp is turned ON.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check tail lamp circuit. Refer to 

EXL-171, "Component Function Check"

.

2.

CHECK PARKING LAMP OPERATION

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check that the parking lamp is turned ON.

Without CONSULT

1. Start IPDM E/R auto active test. Refer to 

PCS-12, "Diagnosis Description"

.

2. Check that the parking lamp is turned ON.
Is the inspection result normal?

YES

>> Parking lamp circuit is normal.

NO

>> Refer to 

EXL-167, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201747

1.

CHECK PARKING LAMP POWER SUPPLY

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

2.

CHECK PARKING LAMP POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector and parking lamp connector.

3. Check continuity between IPDM E/R harness connector and parking lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

TAIL

: Parking lamp ON

Off

: Parking lamp OFF

+

-

Test item

Voltage

IPDM E/R

Connector

Terminal

E14

43

Ground

EXTERNAL 
LAMPS

TAIL

9 – 16 V

Off

0 – 1 V

IPDM E/R

Parking lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E14

43

E44

1

Existed

LH

E28

Revision: November 2015

2016 JUKE

EXL-168

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

PARKING LAMP CIRCUIT

NO

>> Repair or replace harness.

3.

CHECK PARKING LAMP GROUND CIRCUIT

Check continuity between parking lamp harness connector and ground.

Is the inspection result normal?

YES

>> Replace the corresponding front combination lamp. Refer to 

EXL-211, "Removal and Installation"

.

NO

>> Repair or replace harness.

Parking lamp

—

Continuity

Connector

Terminal

RH

E44

2

Ground

Existed

LH

E28

Revision: November 2015

2016 JUKE

FRONT SIDE MARKER LAMP CIRCUIT

EXL-169

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

FRONT SIDE MARKER LAMP CIRCUIT

Component Function Check

INFOID:0000000012201748

1.

CHECK PARKING LAMP OPERATION

Check that the parking lamp is turned ON.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check parking lamp circuit. Refer to 

EXL-167, "Component Function Check"

.

2.

CHECK FRONT SIDE MARKER LAMP OPERATION

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check that the front side marker lamp is turned ON.

Without CONSULT

1. Start IPDM E/R auto active test. Refer to 

PCS-12, "Diagnosis Description"

.

2. Check that the front side marker lamp is turned ON.
Is the inspection result normal?

YES

>> Front side marker lamp circuit is normal.

NO

>> Refer to 

EXL-169, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201749

1.

CHECK FRONT SIDE MARKER LAMP POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector and front side marker lamp connector.

3. Check continuity between IPDM E/R harness connector and front side marker lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK FRONT SIDE MARKER LAMP GROUND CIRCUIT

Check continuity between front side marker lamp harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK FRONT SIDE MARKER LAMP BULB

Check the applicable front side marker lamp bulb.

TAIL

: Front side marker lamp ON

Off

: Front side marker lamp OFF

IPDM E/R

Front side marker lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E14

43

E32

1

Existed

LH

E31

Front side marker lamp

—

Continuity

Connector

Terminal

RH

E32

2

Ground

Existed

LH

E31

Revision: November 2015

2016 JUKE

EXL-170

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

FRONT SIDE MARKER LAMP CIRCUIT

Is the inspection result normal?

YES

>> Check the corresponding front side marker lamp bulb socket. Repair or replace if necessary.

NO

>> Replace the corresponding front side marker lamp bulb. Refer to 

EXL-211, "Replacement"

.

Revision: November 2015

2016 JUKE

TAIL LAMP CIRCUIT

EXL-171

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

TAIL LAMP CIRCUIT

Component Function Check

INFOID:0000000012201750

1.

CHECK TAIL LAMP OPERATION

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check that the tail lamp is turned ON.

Without CONSULT

1. Start IPDM E/R auto active test. Refer to 

PCS-12, "Diagnosis Description"

.

2. Check that the tail lamp is turned ON.
Is the inspection result normal?

YES

>> Tail lamp circuit is normal.

NO

>> Refer to 

EXL-171, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201751

1.

CHECK FUSE

1. Turn ignition switch OFF.

2. Check that the following fuse is not blown (open).

Is the fuse blown (open)?

YES

>> Replace the blown fuse after repairing the affected circuit if a fuse is blown (open).

NO

>> GO TO 2.

2.

CHECK TAIL LAMP POWER SUPPLY

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

3.

CHECK TAIL LAMP POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

TAIL

: Tail lamp ON

Off

: Tail lamp OFF

Unit

Location

Fuse No.

Capacity

• Parking  lamp  RH
• Parking lamp LH
• Front side marker lamp RH
• Front side marker lamp LH
• Tail lamp RH
• Tail lamp LH
• License plate lamp RH
• License plate lamp LH

IPDM E/R

#47

10 A

+

-

Test item

Voltage

IPDM E/R

Connector

Terminal

E14

44

Ground

EXTERNAL 
LAMPS

TAIL

9 – 16 V

Off

0 – 1 V

Revision: November 2015

2016 JUKE

EXL-172

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

TAIL LAMP CIRCUIT

2. Disconnect IPDM E/R connector and rear combination lamp connector.

3. Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK TAIL LAMP GROUND CIRCUIT

Check continuity between rear combination lamp harness connector and ground.

Is the inspection result normal?

YES-1 >> Stop lamp / tail lamp (Bulb side): GO TO 5.

YES-2 >> Tail lamp (LED side): Check the corresponding tail lamp harness, and if check result is normal,

replace the corresponding rear combination lamp. Refer to 

EXL-220, "Removal and Installation"

.

NO

>> Repair or replace harness.

5.

CHECK STOP LAMP / TAIL LAMP BULB

Check the applicable stop lamp / tail lamp bulb.
Is the inspection result normal?

YES

>> Check the corresponding stop lamp / tail lamp bulb socket and harness. Repair or replace if nec-

essary.

NO

>> Repair or replace the corresponding stop lamp / tail lamp bulb. Refer to 

EXL-220, "Replacement"

.

IPDM E/R

Rear combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E14

44

B59

2

Existed

LH

B80

Rear combination lamp

—

Continuity

Connector

Terminal

RH

B59

3

Ground

Existed

LH

B80

Revision: November 2015

2016 JUKE

LICENSE PLATE LAMP CIRCUIT

EXL-173

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

LICENSE PLATE LAMP CIRCUIT

Component Function Check

INFOID:0000000012201752

1.

CHECK TAIL LAMP OPERATION

Check that the tail lamp is turned ON.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check tail lamp circuit. Refer to 

EXL-171, "Component Function Check"

.

2.

CHECK LICENSE PLATE LAMP OPERATION

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check that the license plate lamp is turned ON.

Without CONSULT

1. Start IPDM E/R auto active test. Refer to 

PCS-12, "Diagnosis Description"

.

2. Check that the license plate lamp is turned ON.
Is the inspection result normal?

YES

>> License plate lamp circuit is normal.

NO

>> Refer to 

EXL-173, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201753

1.

CHECK LICENSE PLATE LAMP POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector and back door opener switch connector.

3. Check continuity between IPDM E/R harness connector and back door opener switch harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK LICENSE PLATE LAMP GROUND CIRCUIT

Check continuity between back door opener switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK LICENSE PLATE LAMP BULB

Check the applicable license plate lamp bulb.
Is the inspection result normal?

TAIL

: License plate lamp ON

Off

: License plate lamp OFF

IPDM E/R

Back door opener switch

Continuity

Connector

Terminal

Connector

Terminal

E14

44

D107

5

Existed

Back door opener switch

—

Continuity

Connector

Terminal

D107

6

Ground

Existed

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     366      367      368      369     ..