Nissan Tiida C11. Manual - part 406

EC-274

< COMPONENT DIAGNOSIS >

[HR16DE (WITH EURO-OBD)]

P1572 ASCD BRAKE SWITCH

11.

CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Check the continuity between ASCD brake switch harness connector and ASCD clutch switch harness
connector.

3.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES 

>> GO TO 12.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

12.

CHECK ASCD BRAKE SWITCH

Refer to 

EC-275, "Component Inspection (ASCD Brake Switch)"

.

Is the inspection result normal?

YES

>> GO TO 21.

NO

>> Replace ASCD brake switch.

13.

CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between ECM harness connector and ASCD clutch switch harness connector.

4.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES 

>> GO TO 15.

NO

>> GO TO 14.

14.

DETECT MALFUNCTIONING PART

Check the following.
• Junction block connector M25, M201, M69, E7 (RHD models)
• Harness for open or short between ASCD brake switch and ECM

>> Repair open circuit or short to ground or short to power in harness or connectors.

15.

CHECK ASCD CLUTCH SWITCH

Refer to 

EC-276, "Component Inspection (ASCD Clutch Switch)"

.

Is the inspection result normal?

YES

>> GO TO 21.

NO

>> Replace ASCD clutch switch.

16.

CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect stop lamp switch harness connector.

3.

Check the voltage between stop lamp switch harness connector and ground.

ASCD brake switch

ASCD clutch switch

Continuity

Connector

Terminal

Connector

Terminal

E36 (LHD models)

M205 (RHD models)

2

E35 (LHD models)

M206 (RHD models)

1

Existed

ECM

ASCD clutch switch

Continuity

Connector

Terminal

Connector

Terminal

E16

100

E35 (LHD models)

M206 (RHD models)

2

Existed

P1572 ASCD BRAKE SWITCH

EC-275

< COMPONENT DIAGNOSIS >

[HR16DE (WITH EURO-OBD)]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Is the inspection result normal?

YES

>> GO TO 18.

NO

>> GO TO 17.

17.

DETECT MALFUNCTIONING PART

Check the following.
• 10A fuse (No.7)
• Junction block connector E7, M69 (LHD models)
• Junction block connector M25, M201 (RHD models)
• Harness for open or short between stop lamp switch and battery

>> Repair open circuit or short to ground or short to power in harness or connectors.

18.

CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Disconnect ECM harness connector.

2.

Check the continuity between ECM harness connector and stop lamp switch harness connector.

3.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 20.

NG

>> GO TO 19.

19.

DETECT MALFUNCTIONING PART

Check the following.
• Junction block connector M25, M201, M69, E7 (RHD models)
• Harness for open or short between ECM and stop lamp switch

>> Repair open circuit or short to ground or short to power in harness or connectors.

20.

CHECK STOP LAMP SWITCH

Refer to 

EC-276, "Component Inspection (Stop Lamp Switch)"

.

Is the inspection result normal?

YES

>> GO TO 21.

NO

>> Replace stop lamp switch.

21.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-55, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection (ASCD Brake Switch)

INFOID:0000000001671187

1.

CHECK ASCD BRAKE SWITCH-I

1.

Turn ignition switch OFF.

2.

Disconnect ASCD brake switch harness connector.

3.

Check the continuity between ASCD brake switch terminals under the following conditions.

Stop lamp switch

Ground

Voltage

Connector

Terminal

E13 (LHD models))

M203 (RHD models)

1

Ground

Battery voltage

ECM

Stop lamp switch

Continuity

Connector

Terminal

Connector

Terminal

E16

99

E13 (LHD models)

M203 (RHD models)

2

Existed

EC-276

< COMPONENT DIAGNOSIS >

[HR16DE (WITH EURO-OBD)]

P1572 ASCD BRAKE SWITCH

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK ASCD BRAKE SWITCH-II

1.

Adjust ASCD brake switch installation. Refer to 

BR-6, "Inspection and Adjustment"

.

2.

Check the continuity between ASCD brake switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace ASCD brake switch.

Component Inspection (ASCD Clutch Switch)

INFOID:0000000001671188

1.

CHECK ASCD CLUTCH SWITCH-I

1.

Turn ignition switch OFF.

2.

Disconnect ASCD clutch switch harness connector.

3.

Check the continuity between ASCD clutch switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK ASCD CLUTCH SWITCH-II

1.

Adjust ASCD clutch switch installation. Refer to 

CL-5, "On-vehicle Inspection and Adjustment"

.

2.

Check the continuity between ASCD clutch switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace ASCD clutch switch.

Component Inspection (Stop Lamp Switch)

INFOID:0000000001671189

1.

CHECK STOP LAMP SWITCH-I

1.

Turn ignition switch OFF.

2.

Disconnect stop lamp switch harness connector.

3.

Check the continuity between stop lamp switch terminals under the following conditions.

Terminals

Condition

Continuity

1 and 2

Brake pedal

Fully released

Existed

Slightly depressed

Not existed

Terminals

Condition

Continuity

1 and 2

Brake pedal

Fully released

Existed

Slightly depressed

Not existed

Terminals

Condition

Continuity

1 and 2

Clutch pedal

Fully released

Existed

Slightly depressed

Not existed

Terminals

Condition

Continuity

1 and 2

Clutch pedal

Fully released

Existed

Slightly depressed

Not existed

P1572 ASCD BRAKE SWITCH

EC-277

< COMPONENT DIAGNOSIS >

[HR16DE (WITH EURO-OBD)]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK STOP LAMP SWITCH-II

1.

Adjust stop lamp switch installation. Refer to 

BR-6, "Inspection and Adjustment"

.

2.

Check the continuity between stop lamp switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace stop lamp switch.

Terminals

Condition

Continuity

1 and 2

Brake pedal

Fully released

Not existed

Slightly depressed

Existed

Terminals

Condition

Continuity

1 and 2

Brake pedal

Fully released

Not existed

Slightly depressed

Existed