Nissan Tiida C11. Manual - part 1464

 

  Главная      Nissan     Nissan Tiida C11 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  1462  1463  1464  1465   ..

 

 

Nissan Tiida C11. Manual - part 1464

 

 

BCM (BODY CONTROL MODULE)

WW-51

< ECU DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

ECU DIAGNOSIS

BCM (BODY CONTROL MODULE)

Reference Value

INFOID:0000000001366631

VALUES ON THE DIAGNOSIS TOOL

TERMINAL LAYOUT

Refer to 

BCS-38, "Terminal Layout"

.

PHYSICAL VALUES

Refer to 

BCS-39, "Physical Values"

.

Monitor Item

Condition

Value/Status

FR WASHER SW

Front washer switch OFF

OFF

Front washer switch ON

ON

FR WIPER LOW

Front wiper switch OFF

OFF

Front wiper switch LO

ON

FR WIPER HI

Front wiper switch OFF

OFF

Front wiper switch HI

ON

FR WIPER INT

Front wiper switch OFF

OFF

Front wiper switch INT

ON

FR WIPER STOP

Any position other than front wiper stop position

OFF

Front wiper stop position

ON

H/L SW POS

Lighting switch OFF

OFF

Lighting switch 2ND

ON

LIGHT SW 1ST

Lighting switch OFF

OFF

Lighting switch 2ND

ON

HI BEAM SW

Lighting switch OFF

OFF

Lighting switch HI

ON

H/L WASH SW

NOTE:
The item is indicated, but not monitored

OFF

IGN ON SW

Ignition switch OFF or ACC

OFF

Ignition switch ON

ON

IGN SW CAN

Ignition switch OFF or ACC

OFF

Ignition switch ON

ON

INT VOLUME

Wiper intermittent dial is in a dial position 1 - 7

1 - 7

RR WASHER SW

Rear washer switch OFF

OFF

Rear washer switch ON

ON

RR WIPER INT

Rear wiper switch OFF

OFF

Rear wiper switch INT

ON

RR WIPER ON 

Rear wiper switch OFF

OFF

Rear wiper switch ON

ON

RR WIPER STOP

Rear wiper stop position

OFF

Other than rear wiper stop position

ON

VEHICLE SPEED

While driving

Equivalent to speedometer reading

WW-52

< ECU DIAGNOSIS >

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)

Reference Value

INFOID:0000000001366636

VALUES ON THE DIAGNOSIS TOOL

TERMINAL LAYOUT

Refer to xxx.

PHYSICAL VALUES

Refer to xxx.

Fail Safe

INFOID:0000000001366638

CAN communication control

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.

If no CAN communication is available with BCM

Front wiper control

IPDM E/R detects the front wiper stop position with the front wiper auto stop signal.
When the front wiper auto stop signal is in the conditions listed below, IPDM E/R repeats a front wiper 10 sec-
onds operation and 20 seconds stop five times.

Monitor Item

Condition

Value/Status

HL WASHER REQ

Ignition switch ON, and low 
beam headlamp is ON

Front washer switch OFF

Off

Front washer switch ON
(When headlamp washer is operat-
ing)

On

FR WIP REQ

Ignition switch ON

Front wiper switch OFF

STOP

Front wiper switch INT

1LOW

Front wiper switch LO

Low

Front wiper switch HI

Hi

WIP AUTO STOP

Ignition switch ON

Front wiper stop position

STOP P

Any position other than front wiper 
stop position

ACT P

WIP PROT

Ignition switch ON

Front wiper operates normally

Off

Front wiper stops at fail-safe oper-
ation

BLOCK

IGN RLY

Ignition switch OFF or ACC

Off

Ignition switch ON

On

IGN ON SW

Ignition switch OFF or ACC

Off

Ignition switch ON

On

Control part

Fail-safe in operation

Front wiper

• The status just before activation of fail-safe control is maintained until the ignition 

switch is turned OFF while the front wiper is operating at LO or HI speed.

• The front wiper is operated at LO speed until the ignition switch is turned OFF if the 

fail-safe control is activated while the front wiper is set in the INT mode and the front 
wiper motor is operating.

Headlamp washer

Headlamp washer relay OFF

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)

WW-53

< ECU DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.

Ignition switch

Front wiper switch

Front wiper auto stop signal

ON

OFF

The front wiper auto stop signal (stop posi-
tion) cannot be input for 10 seconds.

ON

The front wiper auto stop signal does not 
change for 10 seconds.

WW-54

< SYMPTOM DIAGNOSIS >

WIPER AND WASHER SYSTEM SYMPTOMS

SYMPTOM DIAGNOSIS

WIPER AND WASHER SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000001366640

CAUTION:

Perform the self-diagnosis with CONSULT-III before performing the diagnosis by symptom. Perform
the diagnosis by DTC if DTC is detected.

Symptom

Probable malfunction location

Inspection item

Front wiper does not 
operate.

HI only

• Combination switch
• Harness between combination switch and BCM
• BCM

Combination switch 
Refer to 

BCS-55, "Symptom 

Table"

.

• IPDM E/R
• Harness between IPDM E/R and front wiper 

motor

• Front wiper motor

Front wiper motor (HI) circuit
Refer to 

WW-20, "Compo-

nent Function Check"

.

Front wiper request signal
• BCM
• IPDM E/R

IPDM E/R DATA MONITOR
"FR WIP REQ"

LO and INT

• Combination switch
• Harness between combination switch and BCM
• BCM

Combination switch
Refer to 

BCS-55, "Symptom 

Table"

.

• IPDM E/R
• Harness between IPDM E/R and front wiper 

motor

• Front wiper motor

Front wiper motor (LO) circuit
Refer to 

WW-18, "Compo-

nent Function Check"

.

Front wiper request signal
• BCM
• IPDM E/R

IPDM E/R DATA MONITOR
"FR WIP REQ"

INT only

• Combination switch
• Harness between combination switch and BCM
• BCM

Combination switch
Refer to 

BCS-55, "Symptom 

Table"

.

Front wiper request signal
• BCM
• IPDM E/R

IPDM E/R DATA MONITOR
"FR WIP REQ"

HI, LO, and INT

SYMPTOM DIAGNOSIS
“FRONT WIPER DOES NOT OPERATE”
Refer to 

WW-58, "Diagnosis Procedure"

.

 

 

 

 

 

 

 

содержание   ..  1462  1463  1464  1465   ..