Nissan Tiida C11. Manual - part 1050

 

  Главная      Nissan     Nissan Tiida C11 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  1048  1049  1050  1051   ..

 

 

Nissan Tiida C11. Manual - part 1050

 

 

LAN

BCM BRANCH LINE CIRCUIT

LAN-457

< COMPONENT DIAGNOSIS >

[CAN SYSTEM (TYPE 32)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

BCM BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000001333564

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the terminals and connectors of the BCM for damage, bend and loose connection (unit side and
connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect the connector of BCM.

2.

Check the resistance between the BCM harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the BCM branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the BCM. Refer to 

BCS-30, "Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the BCM. Refer to 

BCS-57, "Removal and Installation of BCM"

.

YES (Past error)>>Error was detected in the BCM branch line.
NO

>> Repair the power supply and the ground circuit.

BCM harness connector

Resistance (

)

Connector No.

Terminal No.

M18

19

39

Approx. 54 – 66

LAN-458

< COMPONENT DIAGNOSIS >

[CAN SYSTEM (TYPE 32)]

DLC BRANCH LINE CIRCUIT

DLC BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000001333565

INSPECTION PROCEDURE

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the terminals and connectors of the data link connector for damage, bend and loose connection
(connector side and harness side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

Check the resistance between the data link connector terminals.

Is the measurement value within the specification?

YES (Present error)>>Check the CAN system type decision again.
YES (Past error)>>Error was detected in the data link connector branch line circuit.
NO

>> Repair the data link connector branch line.

Data link connector

Resistance (

)

Connector No.

Terminal No.

M22

6

14

Approx. 54 – 66

LAN

EPS BRANCH LINE CIRCUIT

LAN-459

< COMPONENT DIAGNOSIS >

[CAN SYSTEM (TYPE 32)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

EPS BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000001333566

INSPECTION PROCEDURE

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the terminals and connectors of the EPS control unit for damage, bend and loose connection (unit
side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect the connector of EPS control unit.

2.

Check the resistance between the EPS control unit harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the EPS control unit branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the EPS control unit. Refer to 

STC-9, "Diagnosis Proce-

dure"

.

Is the inspection result normal?

YES (Present error)>>Replace the EPS control unit. Refer to 

ST-9, "Removal and Installation"

.

YES (Past error)>>Error was detected in the EPS control unit branch line.
NO

>> Repair the power supply and the ground circuit.

EPS control unit harness connector

Resistance (

)

Connector No.

Terminal No.

M53

9

16

Approx. 54 – 66

LAN-460

< COMPONENT DIAGNOSIS >

[CAN SYSTEM (TYPE 32)]

I-KEY BRANCH LINE CIRCUIT

I-KEY BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000001333567

INSPECTION PROCEDURE

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the terminals and connectors of the Intelligent Key unit for damage, bend and loose connection
(unit side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect the connector of Intelligent Key unit.

2.

Check the resistance between the Intelligent Key unit harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the Intelligent Key unit branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the Intelligent Key unit. Refer to 

SEC-37, "INTELLIGENT

KEY UNIT : Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the Intelligent Key unit. Refer to 

SEC-79, "Removal and Installation"

.

YES (Past error)>>Error was detected in the Intelligent Key unit branch line.
NO

>> Repair the power supply and the ground circuit.

Intelligent Key unit harness connector

Resistance (

)

Connector No.

Terminal No.

M52

2

3

Approx. 54 – 66

 

 

 

 

 

 

 

содержание   ..  1048  1049  1050  1051   ..