Nissan Tiida C11. Manual - part 101

 

  Главная      Nissan     Nissan Tiida C11 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  99  100  101  102   ..

 

 

Nissan Tiida C11. Manual - part 101

 

 

BRC-170

< ECU DIAGNOSIS >

[ESP/TCS/ABS]

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

C1145

YAW RATE SENSOR

XX-XX, "*****"

C1146

SIDE G-SEN CIRCUIT

C1155

BR FLUID LEVEL LOW

BRC-56, "Description"

C1156

ST ANG SEN COM CIR

XX-XX, "*****"

C1160

DECEL G SEN SET

XX-XX, "*****"

C1163

ST ANGL SEN SAFE

XX-XX, "*****"

C1164

CV1

XX-XX, "*****"

C1165

CV2

C1166

SV1

C1167

SV2

C1170

VARIANT CORDING

BRC-38, "DTC Logic"

C1178

ABS ACTIVE BOOSTER SV NG

XX-XX, "*****"

C1179

ABS DELTA S SEN NG

XX-XX, "*****"

C1181

ABS ACTIVE BOOSTER RESPONSE NG

XX-XX, "*****"

C1184

ABS BRAKE RELEASE SW NG

C1189

ABS BRAKE BOOSTER DEFECT

U1000

CAN COMM CIRCUIT

BRC-59, "Description"

DTC

Items (CONSULT screen terms)

Reference

VDC/TCS/ABS

BRC-171

< SYMPTOM DIAGNOSIS >

[ESP/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

SYMPTOM DIAGNOSIS

VDC/TCS/ABS

Symptom Table

INFOID:0000000001731200

If ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp turn ON, perform self-diagnosis.

NOTE:

• 1: The ABS does not operate when the speed is 10 km/h (6 MPH) or less.

• 2: Under the following conditions, ABS is activated and vibration is felt when brake pedal is lightly depressed. However, this is normal.

- When shifting gears

- When driving on slippery road

- During cornering at high speed

- When passing over bumps or grooves [at approximately 50 mm (1.97 in) or more]

- When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher]

Symptom

Check item

Reference

Excessive ABS function operation fre-
quency

Brake force distribution

BRC-74, "Diagno-

sis Procedure"

Looseness of front and rear axle

Wheel sensor and rotor system

Unexpected pedal reaction

Brake pedal stroke

BRC-75, "Diagno-

sis Procedure"

Make sure the braking force is sufficient when the ABS is not operating.

The braking distance is long

Check stopping distance when the ABS is not operating.

BRC-76, "Diagno-

sis Procedure"

ABS function does not operate (Note 1)

ABS actuator and electric unit (control unit)

BRC-77, "Diagno-

sis Procedure"

Pedal vibration or ABS operation sound 
occurs (Note 2)

Brake pedal

BRC-78, "Diagno-

sis Procedure"

ABS actuator and electric unit (control unit)

Vehicle jerks during VDC/TCS/ABS con-
trol

ABS actuator and electric unit (control unit)

XX-XX, "*****"

TCM

ECM

BRC-172

< SYMPTOM DIAGNOSIS >

[ESP/TCS/ABS]

EXCESSIVE ABS FUNCTION OPERATION FREQUENCY

EXCESSIVE ABS FUNCTION OPERATION FREQUENCY

Diagnosis Procedure

INFOID:0000000001731201

1.

CHECK START

Check front and rear brake force distribution using a brake tester.
Is the inspection result normal?

YES

>> GO TO 2

NO

>> Check brake system.

2.

CHECK FRONT AND REAR AXLE

Make sure that there is no excessive play in the front and rear axles. Refer to front: 

FAX-5, "On-Vehicle

Inspection and Service"

, Rear: 

RAX-5, "On-Vehicle Inspection and Service"

.

Is the inspection result normal?

YES

>> GO TO 3

NO

>> Repair or replace malfunctioning components.

3.

CHECK WHEEL SENSOR AND SENSOR ROTOR

Check the following.
• Wheel sensor installation for damage.
• Sensor rotor installation for damage. 
• Wheel sensor connector connection.
• Wheel sensor harness inspection.

Is the inspection result normal?

YES

>> GO TO 4

NO

>> • Replace wheel sensor or sensor rotor. Refer to 

BRC-182, "Removal and Installation"

.

• Repair harness.

4.

CHECK ABS WARNING LAMP DISPLAY

Make sure that the ABS warning lamp is turned off after the ignition switch is turned ON or when driving. 

Is the ABS warning lamp illuminated?

YES

>> Perform self-diagnosis. Refer to 

BRC-105, "CONSULT-III Function (ABS)"

.

NO

>> Normal

UNEXPECTED PEDAL REACTION

BRC-173

< SYMPTOM DIAGNOSIS >

[ESP/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

UNEXPECTED PEDAL REACTION

Diagnosis Procedure

INFOID:0000000001731202

1.

CHECK BRAKE PEDAL STROKE

Check brake pedal stroke. Refer to 

BR-6, "Inspection and Adjustment"

.

Is the stroke too large?

YES

>> • Bleed air from brake tube and hose. Refer to 

BR-8, "Bleeding Brake System"

.

• Check brake pedal, brake booster, and master cylinder for mount play, looseness, brake system

fluid leakage, etc. Refer to 

BR-6, "Inspection and Adjustment"

 (brake pedal), 

BR-18, "On-Board

Inspection"

 (master cylinder), 

BR-19, "On Board Inspection"

 (brake booster).

NO

>> GO TO 2

2.

CHECK FUNCTION

Disconnect ABS actuator and electric unit (control unit) connector to deactivate ABS. Check if braking force is
normal in this condition. Connect connector after inspection.

Is the inspection result normal?

YES

>> Normal

NO

>> Check brake system.

 

 

 

 

 

 

 

содержание   ..  99  100  101  102   ..