Nissan Tiida C11. Manual - part 39

BCS-20

< FUNCTION DIAGNOSIS >

DIAGNOSIS SYSTEM (BCM)

DATA MONITOR

ACTIVE TEST

HEADLAMP

HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)

INFOID:0000000001451470

WORK SUPPORT

*: Initial setting

DATA MONITOR

Work Item

Description

HAZARD LAMP SET

Answer back function (hazard) mode can be changed in this mode.
For the detail of the setting, refer to 

DLK-617, "REMOTE KEYLESS ENTRY : System Descrip-

tion"

.

AUTO LOCK SET

Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 2 minutes
• MODE 3: 3 minutes
• MODE 4: 4 minutes
• MODE 5: 5 minutes

Monitor Item

[Unit}

Condition

IGN ON SW [ON/OFF]

Indicates condition of ignition switch in ON position.

KEY SW [ON/OFF]

Indicates condition of key switch.

KEYLESS LOCK [ON/OFF]

Indicates condition of lock signal from keyfob.

KEYLESS UNLOCK [ON/OFF]

Indicates condition of unlock signal from keyfob.

DOOR SW-DR [ON/OFF]

Indicates condition of front door switch (driver side).

DOOR SW-AS [ON/OFF]

Indicates condition of front door switch (passenger side).

DOOR SW-RR [ON/OFF]

Indicates condition of rear door switch RH.

DOOR SW-RL [ON/OFF]

Indicates condition of rear door switch LH.

BACK DOOR SW [ON/OFF]

Indicates condition of back door switch.

CDL LOCK SW [ON/OFF]

Indicates condition of door lock and unlock switch.

CDL UNLOCK SW [ON/OFF]

Indicates condition of door lock and unlock switch.

RKE LOCK AND UNLOCK

This item is indicated, but not monitored.

Test Item

Description

DOOR LOCK

This test is able to check warning chime in combination meter operation. [ALL LOCK/ALL UN-
LOCK/DR UNLOCK/OTHER UNLOCK]

INT LAMP

This test is able to check interior lamp operation [ON/OFF]. 

FLASHER

This test is able to check flasher operation [LH/RH/OFF].

Work item

Setting

Description

BATTERY SAVER SET

ON*

Battery saver mode can be changed.

OFF

Monitor item

[Unit]

Description

IGN ON SW [ON/OFF]

Ignition switch (ON) status judged from IGN signal (ignition power supply)

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-21

< FUNCTION DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ACTIVE TEST

WIPER

WIPER : CONSULT-III Function (BCM - WIPER)

INFOID:0000000001451471

WORK SUPPORT

HI BEAM SW [ON/OFF]

Each switch status that BCM judges from the combination switch reading function

H/L SW POS [ON/OFF]

LIGHT SW 1ST [ON/OFF]

PASSING SW [ON/OFF]

AUTO LIGHT SW [ON/OFF]

FR FOG SW [ON/OFF]

RR FOG SW [ON/OFF]

DOOR SW-DR [ON/OFF]

The switch status input from front door switch (driver side)

ENGINE STATUS

The engine status received from ECM with CAN communication

LIT-SEN FAIL [OK/NOTOK]

• The sensor status received from light & rain sensor with serial link
• The serial link condition that BCM judges

AUT LIGHT SYS [ON/OFF]

Auto light system status that BCM judges from the vehicle condition

Monitor item

[Unit]

Description

Test item

Operation

Description

TAIL LAMP

ON

Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.

OFF

Stops the tail lamp request signal transmission.

HEAD LAMP

HI

Transmits the high beam request signal with CAN communication to turn 
the headlamp (HI).

LO

Transmits the low beam request signal with CAN communication to turn 
the headlamp (LO).

OFF

Stops the high & low beam request signal transmission.

FR FOG LAMP

ON

Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.

OFF

Stops the front fog lights request signal transmission.

RR FOG LAMP

ON

• Outputs the voltage to turn the rear fog lamp ON.
• Transmits the rear fog lamp status signal to the combination meter with 

CAN communication to turn the rear fog lamp indicator lamp ON.

OFF

• Stops the voltage to turn the rear fog lamp OFF.
• Stops the rear fog lamp status signal transmission.

DAYTIME RUNNING LIGHT

ON

Transmits the day time running light request signal to IPDM E/R with 
CAN communication to turn the each lamps ON.

OFF

Stops the day time running light request signal transmission.

Work Item

Setting 

Item

Description

WIPER SPEED 
SETTING

ON

1

With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)

OFF

Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)

RR WIP RVRS 
SET

ON

2

Change ON/OFF mode setting or rear wiper operation when gear is shifted to reverse

OFF

BCS-22

< FUNCTION DIAGNOSIS >

DIAGNOSIS SYSTEM (BCM)

1: Factory setting

2: If equipped

DATA MONITOR

ACTIVE TEST

FLASHER

FLASHER : CONSULT-III Function (BCM - FLASHER)

INFOID:0000000001451472

WORK SUPPORT

DATA MONITOR

Monitor Item

[Unit]

Description

IGN ON SW [ON/OFF]

Ignition switch ON status judged from ignition power supply.

FR WIPER HI [ON/OFF]

Each switch status that BCM judges from the combination switch reading function.

FR WIPER LOW [ON/OFF]

FR WIPER INT [ON/OFF]

FR WASHER SW [ON/OFF]

INT VOLUME [1 - 7]

Each switch status that BCM judges from the combination switch reading function.

FR WIPER STOP [ON/OFF]

Front wiper motor (stop position) status received from IPDM E/R with CAN communica-
tion.

VEHICLE SPEED [km/h]

The value of the vehicle speed signal received from combination meter with CAN com-
munication.

H/L SW POS [ON/OFF]

RR WIPER ON [ON/OFF]

Each switch status that BCM judges from the combination switch reading function.

RR WIPER INT [ON/OFF]

RR WASHER SW [ON/OFF]

RR WIPER STOP [ON/OFF]

Rear wiper motor (stop position) status input from the rear wiper motor.

REVERSE SW CAN [ON/OFF]

Transmission reverse position moitored via CAN.

Test Item

Operation

Description

HEADLAMP WASH-
ER

ON

Transmits the headlamp washer request signal to IPDM E/R with CAN communication to 
operate the headlamp washer operation.

FR WIPER

HI

Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
erate the front wiper HI operation.

LO

Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to 
operate the front wiper LO operation.

INT

Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to 
operate the front wiper INT operation.

OFF

Stops transmitting the front wiper request signal to stop the front wiper operation.

RR WIPER

ON

Outputs the voltage to operate the rear wiper motor.

OFF

Stops the voltage to stop.

Work Item

Description

HAZARD LAMP SET

Operation

MODE1

MODE2

MODE3

MODE4

Keyfob operation

Lock

Unlock

Lock

Unlock

Lock

Unlock

Lock

Unlock

Hazard lamp flash

-

-

-

Twice

Once

-

Once

Twice

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-23

< FUNCTION DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ACTIVE TEST

AIR CONDITIONER

AIR CONDITIONER : CONSULT-III Function (BCM - AUTO AIR CONDITIONER)

INFOID:0000000001451473

ACTIVE TEST

DATA MONITOR

INTELLIGENT KEY

INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)

INFOID:0000000001451474

DATA MONITOR

Monitor Item

[Unit]

Description

IGN ON SW [ON/OFF]

Ignition switch (ON) status judged from IGN signal (ignition power supply)

HAZARD SW [ON/OFF]

The switch status input from the hazard switch

TURN SIGNAL R [ON/OFF]

Each switch condition that BCM judges from the combination switch reading function

TURN SIGNAL L [ON/OFF]

TURN/L MNTR [ON/OFF]

Displays status (one bulb out: ON/other: OFF) as judged from bulb signal

Test Item

Operation

Description

FLASHER

RH

Outputs the voltage to turn the right side turn signal lamps ON.

LH

Outputs the voltage to turn the left side turn signal lamps ON.

OFF

Stops the voltage to turn the turn signal lamps OFF.

Test Item

Operation

Description

A?C INDICATOR

ON

Outputs the signal to turn the A/C indicator ON.

OFF

Stops the signal to turn the A/C indicator OFF.

Monitor Item

[Unit]

Contents

IGNSW [ON/OFF]

Display [ignition switch position (On)/(Off), ACC position (Off)] status as judged form ignition 
switch signal.

FAN ON SIG [ON/OFF]

Display [FAN (On)/FAN (Off)] status as judged form blower fan motor switch signal.

AIR COND SW [ON/OFF]

Display [COMP (On)/COMP (Off)] status as judged form air conditioner switch signal.

Monitor Item

[Unit]

Condition

IGN ON SW [ON/OFF]

Indicates condition of ignition switch in ON position.

PUSH SW [ON/OFF]

Indicates condition of ignition knob switch.

I-KEY LOCK [ON/OFF]

Indicates condition of lock signal from Intelligent Key.

I-KEY UNLOCK [ON/OFF]

Indicates [condition of unlock signal from Intelligent Key.

I-KEY ALL UNL [ON/OFF]

Indicates condition of all unlock signal from Intelligent Key.

I-KEY TRUNK OP [ON/OFF]

Indicates condition of trunk open signal from Intelligent Key.

DOOR SW-DR [ON/OFF]

Indicates condition of front door switch (driver side).

DOOR SW-AS [ON/OFF] 

Indicates condition of front door switch (passenger side).

DOOR SW-RR [ON/OFF]

Indicates condition of rear door switch RH.