Mitsubishi Outlander GS45X. Manual - part 440

 

  Index      Mitsubishi     Mitsubishi Outlander GS45X - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  438  439  440  441   ..

 

 

Mitsubishi Outlander GS45X. Manual - part 440

 

 

DIAGNOSIS

TSB Revision

ACTIVE STABILITY CONTROL SYSTEM (ASC)

35C-187

STEP 3. Check whether the DTC is reset.
Erase the DTC.
Q: Is DTC C2002 set?

YES : Return to Step 1.
NO :  The procedure is complete.

DTC C2003: Control parameter not implement

CAUTION

• If there is any problem in the CAN bus lines, an incor-

rect diagnostic trouble code may be set. Prior to this 
diagnosis, diagnose the CAN bus lines (Refer to 
GROUP 54C 

 CAN Bus Line Diagnostic Flow 

P.54C-10

).

• If diagnostic trouble code No.C2003 is set in ASC-ECU, 

always diagnose the CAN bus line. If there is any fault 
in the CAN bus lines, an incorrect diagnostic trouble 
code may be set. In this case, the set diagnostic trouble 
code is not highly reliable.

• Before replacing the ECU, ensure that the communica-

tion circuit is normal.

• When diagnostic trouble code C2003 is set in 

ASC-ECU, the diagnostic trouble code may also be set 
in ETACS-ECU. When the diagnostic trouble code is set 
in ETACS-ECU, carry out the diagnosis of the diagnos-
tic trouble code for ETACS-ECU first.

• When the hydraulic unit (integrated with ASC-ECU) is 

replaced, always carry out the calibration of the steer-
ing wheel sensor, the G and yaw rate sensor and brake 
fluid pressure sensor (Refer to 

P.35C-282

P.35C-283

 

and 

P.35C-284

).

.

DTC SET CONDITIONS

ASC-ECU communicates with ETACS-ECU via CAN bus lines. 
When received unset vehicle information from the 
ETACS-ECU, this diagnostic trouble code is set.

.

PROBABLE CAUSES

• ETACS-ECU or ASC-ECU which was equipped with other 

vehicle is used.

• Faulty installation of ETACS-ECU or ASC-ECU

• Faulty ETACS-ECU coding

• Malfunction of ETACS-ECU

• ASC-ECU malfunction

DIAGNOSIS

Required Special Tools:

• MB991958: Scan Tool (M.U.T.-III Sub Assembly)

• MB991824: Vehicle Communication Interface (V.C.I.)

DIAGNOSIS

TSB Revision

ACTIVE STABILITY CONTROL SYSTEM (ASC)

35C-188

• MB991827: M.U.T.-III USB Cable

• MB991910: M.U.T.-III Main Harness A

STEP 1. Using scan tool MB991958, diagnose the CAN bus 
line.
Use scan tool to diagnose the CAN bus lines.
Q: Is the check result normal?

YES : Go to Step 3.
NO :  Repair the CAN bus lines (Refer to GROUP 54C 

− 

CAN Bus Diagnostics Table 

P.54C-17

). On 

completion, go to Step 2.

STEP 2. Diagnostic trouble code recheck after resetting 
CAN bus lines
Q: Is DTC C2003 set?

YES : Go to Step 3.
NO :  The procedure is complete.

STEP 3. Scan tool other system DTC
Use scan tool to check whether any coding-related diagnostic 
trouble code is set by ETACS-ECU.
Q: Is the DTC set?

YES : Troubleshoot for the relevant diagnostic trouble code 

(Refer to GROUP 54A 

− ETACS-ECU/Diagnostic 

Trouble Code Chart 

P.54A-732

). Then go to Step 8.

NO :  Go to Step 4.

STEP 4. Check part number of ASC-ECU
Check the part number of ASC-ECU.
Q: Is the check result normal?

YES : Go to Step 5.
NO :  Replace the hydraulic unit (integrated with ASC-ECU) 

(Refer to 

P.35C-287

). Then go to Step 8.

DIAGNOSIS

TSB Revision

ACTIVE STABILITY CONTROL SYSTEM (ASC)

35C-189

STEP 5. ETACS-ECU coding data check
Refer to GROUP 00 

− Precautions before Service/Coding List 

P.00-44

.

Vehicle line

OK: OUTLANDER

Transmission

OK (A/T): 6AT
OK (CVT): CVT

Engine type

OK (2.4L engine): 2.4L D4 MPI VVT
OK (3.0L engine): 3.0L S4 MIVEC

Engine power

OK: Normal

Chassis type for A.S.C.

OK : Type 2

Final drive

OK (FWD): Front Drive
OK (AWD): 4WD FF Base

Front differential

OK (except S-AWC): Open
OK (S-AWC): ELSD

Transfer

OK (FWD): FWD
OK (AWD): ECC

SAS

OK: Present

4WD/AWD

OK (FWD): Not present
OK (AWD): Present

TCM

OK: Present

ACDAYC

OK: Not present

Q: Is the check result normal?

YES : Go to Step 6.
NO :  Replace the ETACS-ECU (Refer to GROUP 54A 

− 

ETACS-ECU 

P.54A-825

), and then go to Step 8.

STEP 6. Check part number of ETACS-ECU
Check the part number of ETACS-ECU.
Q: Is the check result normal?

YES : Go to Step 7.
NO :  Replace the ETACS-ECU (Refer to GROUP 54A 

− 

ETACS-ECU 

P.54A-825

), and then go to Step 8.

DIAGNOSIS

TSB Revision

ACTIVE STABILITY CONTROL SYSTEM (ASC)

35C-190

STEP 7. Check whether the diagnostic trouble code is 
reset.
Erase the DTC.
Q: Is DTC C2003 set?

YES : Replace the hydraulic unit (integrated with ASC-ECU) 

(Refer to 

P.35C-287

). Then go to Step 8.

NO :  The trouble can be an intermittent malfunction (Refer 

to GROUP 00 

− How to Use Troubleshooting/How to 

Cope with Intermittent Malfunctions 

P.00-15

).

STEP 8. Check whether the diagnostic trouble code is 
reset.
Erase the DTC.
Q: Is DTC C2003 set?

YES : Return to Step 1.
NO :  The procedure is complete.

 

 

 

 

 

 

 

Content   ..  438  439  440  441   ..