Mitsubishi Outlander (2013+). Manual - part 111

ETACS

CHASSIS ELECTRICAL

54A-44

System configuration

OPERATION

1. When the ignition key is inserted to the ignition

switch or the ignition switch is turned to the ON
position, ETACS-ECU starts operation of receiver
antenna, and starts communication with ignition
key (transponder) by radio frequency.

2. When the ignition key receives the request signal

to start the communication from receiver antenna
via immobilizer antenna, then transponder starts
the communication and send the signal for
communication to receiver antenna via
immobilizer antenna.

3. Receiver antenna sends the codes (key ID, etc)

sent from the ignition key to the ETACS-ECU.

4. ETACS-ECU compares the codes (key ID, etc)

sent from receiver antenna with the
already-registered ID code and self calculated
value, and then reflect the result of transponder
communication to the certification communication
with engine ECU.

NOTE:

•

The transponder integrated in the ignition key
uses the power supplied from receiver antenna
via immobilizer antenna. Therefore, it can be
used regardless of the battery in ignition key (for
transmitter).

•

Two ignition keys (transmitter and transponder)
are provided, and up to eight keys can be regis-
tered to one vehicle as needed.

•

When ETACS-ECU is replaced or when the key
is lost or added, the ID codes for all the keys (key
ID) must be registered using M.U.T.-III.

ETACS

GENERAL INFORMATION

M2545400200722

ETACS

-ECU has three main functions (gateway

function, coding function, body electrical equipment
control function).

ACC00115

ETACS-ECU

Turn-signal lamp

Receiver
antenna

Steering lock
(immobilizer
antenna)

Engine-ECU

Lock switch

Unlock switch

CAN-C
communication

Ignition key

Radio
frequency
signal
(Transponder)

Radio
frequency
signal (Transmitter)

Room lamp,
Ignition key cylinder
illumination lamp

Power window switch

Door lock actuator

Door mirror assembly

Transmitter

Transponder

Tailgate latch
assembly

ETACS

CHASSIS ELECTRICAL

54A-45

NOTE:

: ETACS (Electronic Time and Alarm Control

System)

GATEWAY FUNCTION

As a central ECU for the on-vehicle communication
network system established in the vehicle, the gate-
way function is integrated into ETACS-ECU. The
gateway function offers the following functions:

• Data transfer among three networks

Transfers the data flowing in a network to another

network in real time.

NOTE:

: CAN

-C (power train network),

CAN

-C-Mid (middle-speed body network), LIN

(low-speed body network)

NOTE:

: For details of CAN, refer to GROUP 54C,

Controller Area Network (CAN) .

NOTE:

: For details of LIN, refer to GROUP 54B,

Local Interconnect Network (LIN) .

• Diagnosis of each network communication line

Detects and stores an open circuit and short circuit of

communication line.

• Communication error diagnosis of network ECUs

Detects and stores the ECU that is not properly

transmitting data.

CODING FUNCTION

By writing the coding data such as vehicle model,
destination, and equipment level to ECUs, the func-
tions of ECUs can be changed. There are two types
of coding method, the local coding and global coding.

BODY ELECTRICAL EQUIPMENT
CONTROL FUNCTION

This function controls the following electrical equip-
ment.

• Exterior lamps

• Wiper, washer

• Central door locking system

• Interior lamp

• Electric-folding door mirror <vehicles with electric

retractable remote controlled door mirrors>

• Keyless entry, keyless operation system <vehi-

cles with KOS>

• Power supply control

• Immobilizer system <vehicles without electric

retractable remote controlled door mirrors>

• Headlamp automatic levelling system <vehicles

with headlamp automatic levelling system>

FUNCTION AND CONTROL BY ETACS-ECU.

M2545400300547

POWER SUPPLY CONTROL

ACC POWER CUT-OFF FUNCTION <INI-
TIAL CONDITION: 30 MINUTES>

The function has been added that the ACC power
supply is cut-off when 30 or 60 minutes has elapsed
with the ignition switch in the ACC position.

NOTE: Using a customise function, the availability of
ACC power cut-off function and its time to ACC
power cut-off can be set. (Refer to Customise Func-
tion

P.54A-45

CUSTOMISATION FUNCTION

M2545400400942

By operating the M.U.T.-III ETACS system, the fol-
lowing functions can be customised. The pro-
grammed information is held even when the battery
is disconnected.

ACC00079AB

ETACS-ECU

LIN

CAN-C-Mid

CAN-C

ETACS

CHASSIS ELECTRICAL

54A-46

Adjustment
item (M.U.T.-III
display)

Adjustment item

Adjusting content
(M.U.T.-III display)

Adjusting content

Turn power
source

Adjustment of
turn-signal lamp
operation condition

ACC or IG1

Operable with ACC or ON position

IG1

Operable with ON position (initial
condition)

Comfort flasher

With/without
comfort flasher
function

Disable

No function

Enable

With function (initial condition)

Hazard answer
back

Adjustment of the
number of keyless
hazard warning
lamp answer back
flashes

Lock:1, Unlock:2

LOCK: Flashes once, UNLOCK: Flashes
twice (initial condition)

Lock:1, Unlock:0

LOCK: Flashes once, UNLOCK: No flash

Lock:0, Unlock:2

LOCK: No flash, UNLOCK: Flash twice

Lock:2, Unlock:1

LOCK: Flash twice, UNLOCK: Flash once

Lock:2, Unlock:0

LOCK: Flash twice, UNLOCK: No flash

Lock:0, Unlock:1

LOCK: No flash, UNLOCK: Flash once

Lock:0, Unlock:0

No function

Front wiper
operation

Adjustment of the
intermittent
windshield wiper
operation <vehicles
without lighting
control sensor>

Normal INT

Intermittent wiper interval is fixed to 4
seconds.

Variable INT

Intermittent wiper interval is calculated only
by the wiper volume control.

Speed Sensitive

Intermittent wiper interval is calculated
according to the intermittent wiper volume
control and vehicle speed (initial
condition).

Adjustment of the
intermittent
windshield wiper
operation <vehicles
with lighting control
sensor>

Normal INT

Intermittent wiper interval is fixed to 4
seconds.

Variable INT

Intermittent wiper interval is calculated only
by the wiper volume control.

Speed Sensitive

Intermittent wiper interval is calculated
according to the intermittent wiper volume
control and vehicle speed.

Rain Sensitive

Intermittent wiper interval is calculated
according to the intermittent wiper volume
control and lighting control sensor (initial
condition).

Front/rear wiper
washer

Disabling or
enabling
washer-linked wiper
function

Only Washer

No function

Washer & Wiper

With function: Without delayed finishing
wipe function <Initial condition>

With after wipe

With function: With delayed finishing wipe
function

Intermittent time
of rear wiper

Adjustment of rear
wiper interval

0 sec.

No wiper interval

4 sec.

4 seconds

8 sec.

8 seconds (initial condition)

16 sec.

16 seconds

ETACS

CHASSIS ELECTRICAL

54A-47

Rear wiper Low
speed mode

Disabling or
enabling rear wiper
continuous
operation

Disable

No function

Enable

With function (initial condition)

Auto fold mirror

Electric folding door
mirror automatic
unfolding function
<vehicles with
electric retractable
remote controlled
door mirrors>

Not Auto

No synchronised operation

Open Vehicle SPD

Vehicle speed-dependent operation

Open/Close by IG

Ignition switch linked operation

OPN/CLS Keyless

Keyless entry linked operation (initial
condition)

Sensitivity for
auto lamp

Lighting control
sensor sensitivity
(illumination
intensity) <vehicles
with lighting control
sensor>

Level 1 bright

High ambient brightness

Level 2 bright

Standard ambient brightness (initial
condition)

Level 3

Low ambient brightness

Level 4 dark

Low-low ambient brightness

Room lamp
delay timer with
door

Adjustment of
interior lamp delay
shutdown time

0 sec.

0 second (no delay shutdown time)

7.5 sec.

7.5 seconds

15 sec.

15 seconds (initial condition)

30 sec.

30 seconds

60 sec.

60 seconds

120 sec.

120 seconds

180 sec.

180 seconds

Head lamp auto
cut customise

Adjustment of
headlamp
automatic shutdown
function

Disable

No function

Enable (B-spec.)

With function (initial condition)

Interior lamp
auto cut timer

Adjustment of
interior lamp
automatic shutdown
function operation
time

Disable

No function

3 min

3 minutes

30 min

30 minutes (initial condition)

60 min

60 minutes

Comfort flasher
switch time

Switch operation
time to activate the
comfort flasher
function

Normal

0.4 second (initial condition)

Long

0.8 second

Intelligent/Comf
ort washer

With/without
Comfort washer
function

Disable

No function (Initial condition)

Enable

With function

Adjustment
item (M.U.T.-III
display)

Adjustment item

Adjusting content
(M.U.T.-III display)

Adjusting content

Content .. 109 110 111 112 ..