Mitsubishi Galant 9G. Manual - part 543

 

  Index      Mitsubishi     Mitsubishi Galant 9G - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  541  542  543  544   ..

 

 

Mitsubishi Galant 9G. Manual - part 543

 

 

AUTOMATIC TRANSAXLE DIAGNOSIS

TSB Revision

AUTOMATIC TRANSAXLE

23A-250

LOGIC FLOW CHARTS (Monitor Sequence) <DTC 43 (P0733)>

.

Yes

No

No

N

E

 : 

Engine speed

START

Yes

No

Transmission fluid temperature 
sensor voltage < 4.5 V

There is only one transmission 
range switch signal

Yes

N

E

 > 450 r/min

N

OPG-B

 > 900 r/min

N

IPG-A

 > 0 r/min

Continuous failure for 4 secs.

Good

END

N

OPG-B 

: Output speed

            (output shaft speed sensor)

No

Yes

No

No

Yes

No

Yes

Yes

Malfunction

Shift change is finished

N

IPG-A 

: Input speed

           (input shaft speed sensor)

I

3

 : 3rd g

ear ratio

AC205245

Timer start

Timer > 2 secs.

Voltage of battery > 10 V

Shift stage commanded 
by A/T ECM is 3rd

No

Yes

Yes

No

I

3

 × N

OPG-B

 - 200 < N

IPG-A

 < I

3

 × N

OPG-B

 + 200

AB

Shift stage commanded 
        by PCM is 3rd

AUTOMATIC TRANSAXLE DIAGNOSIS

TSB Revision

AUTOMATIC TRANSAXLE

23A-251

DTC SET CONDITIONS <DTC 43 (P0733)>

Check Conditions

• Engine speed: 450 r/min or more.

• Output speed: 900 r/min or more.

• Shift stage: 3rd gear.

• Input speed: more than 0 r/min.

• Transmission fluid temperature sensor voltage: 

4.5 volts or less.

• Voltage of battery: 10 volts or more.

• Transmission range switch rationality: only one 

signal.

• Time after shift changing finish: 2 seconds or 

more.

Judgement Criteria

• Output speed: [(input speed + 200 r/min) / 3rd 

gear ratio] or more. (4 seconds)

• Output speed: [(input speed - 200 r/min) / 3rd 

gear ratio] or less. (4 seconds)

• If DTC 43 (P0733) is set consecutively four times, 

the transaxle is locked into 3rd gear as a fail-safe 
measure, and the "N" range light flashes once 
per second.

.

OBD-II DRIVE CYCLE PATTERN <DTC 43 
(P0733)>

Start the engine, and drive at 40 km/h (25 mph) or 
more for 10 seconds, with 3rd gear fixed (3rd gear in 
sport mode).

.

DESCRIPTIONS OF MONITOR METHODS 
<DTC 44 (P0734)>

• In 4th gear, if a difference between turbine revolu-

tion and that value calculated from output revolu-
tion equals or exceeds specified value, PCM 
judges that step-out in 4th gear has occurred.

.

MONITOR EXECUTION <DTC 44 (P0734)>

• Continuous

.

MONITOR EXECUTION CONDITIONS 
(OTHER MONITOR AND SENSOR) <DTC 
44 (P0734)>

Other Monitor (There is no temporary DTC stored 

in memory for the item monitored below)

• DTC 27, 28 (P0705): Transmission range switch 

malfunction

• DTC 22 (P0715): Input shaft speed sensor mal-

function

• DTC 23 (P0720): Output shaft speed sensor mal-

function

• DTC 36 (P0743): Torque converter clutch sole-

noid malfunction

• DTC 31 (P0753): Low-reverse solenoid malfunc-

tion

• DTC 32 (P0758): Underdrive solenoid malfunc-

tion

• DTC 33 (P0763): Second solenoid malfunction

• DTC 34 (P0768): Overdrive solenoid malfunction

• DTC 54 (P1751): A/T control relay malfunction

Sensor (The sensor below is determined to be 

normal)

• Input shaft speed sensor

• Output shaft speed sensor

• Transmission range switch

• Torque converter clutch solenoid

• Low-reverse solenoid

• Underdrive solenoid

• Second solenoid

• Overdrive solenoid

• A/T control relay

.

AUTOMATIC TRANSAXLE DIAGNOSIS

TSB Revision

AUTOMATIC TRANSAXLE

23A-252

LOGIC FLOW CHARTS (Monitor Sequence) <DTC 44 (P0734)>

.

Yes

No

No

N

E

 : 

Engine speed

START

Yes

No

Transmission fluid temperature 
sensor voltage < 4.5 V

There is only one transmission 
range switch signal

Yes

N

E

 > 450 r/min

N

OPG-B

 > 900 r/min

N

IPG-A

 > 0 r/min

Continuous failure for 4 secs.

Good

END

N

OPG-B 

: Output speed

            (output shaft speed sensor)

No

Yes

No

No

Yes

No

Yes

Yes

Malfunction

Shift change is finished

N

IPG-A 

: Input speed

           (input shaft speed sensor)

I

4

 : 4th g

ear ratio

AC205246

Timer start

Timer > 2 secs.

Voltage of battery > 10 V

Shift stage commanded 
by A/T ECM is 4th

No

Yes

Yes

No

I

4

 × N

OPG-B

 - 200 < N

IPG-A

 < I

4

 × N

OPG-B

 + 200

AB

Shift stage commanded 
        by PCM is 4th

AUTOMATIC TRANSAXLE DIAGNOSIS

TSB Revision

AUTOMATIC TRANSAXLE

23A-253

DTC SET CONDITIONS <DTC 44 (P0734)>

Check Conditions

• Engine speed: 450 r/min or more.

• Output speed: 900 r/min or more.

• Shift stage: 4th gear.

• Input speed: more than 0 r/min.

• Transmission fluid temperature sensor voltage: 

4.5 volts or less.

• Voltage of battery: 10 volts or more.

• Transmission range switch rationality: only one 

signal.

• Time after shift changing finish: 2 seconds or 

more.

Judgement Criteria

• Output speed: [(input speed + 200 r/min) / 4th 

gear ratio] or more. (4 seconds)

• Output speed: [(input speed - 200 r/min) / 4th 

gear ratio] or less. (4 seconds)

• If DTC 44 (P0734) is set consecutively four times, 

the transaxle is locked into 3rd gear as a fail-safe 
measure, and the "N" range light flashes once 
per second.

.

OBD-II DRIVE CYCLE PATTERN <DTC 44 
(P0734)>

Start the engine, and drive at 40 km/h (25 mph) or 
more for 10 seconds, with 4th gear fixed (4th gear in 
sport mode).

.

DESCRIPTIONS OF MONITOR METHODS 
<DTC 46 (P0736)>

• In reverse gear, if a difference between turbine 

revolution and that value calculated from output 
revolution equals or exceeds specified value, 
PCM judges that step-out in reverse gear has 
occurred.

.

MONITOR EXECUTION <DTC 46 (P0736)>

• Continuous

.

MONITOR EXECUTION CONDITIONS 
(OTHER MONITOR AND SENSOR) <DTC 
46 (P0736)>

Other Monitor (There is no temporary DTC stored 

in memory for the item monitored below)

• DTC 27, 28 (P0705): Transmission range switch 

malfunction

• DTC 22 (P0715): Input shaft speed sensor mal-

function

• DTC 23 (P0720): Output shaft speed sensor mal-

function

• DTC 36 (P0743): Torque converter clutch sole-

noid malfunction

• DTC 31 (P0753): Low-reverse solenoid malfunc-

tion

• DTC 32 (P0758): Underdrive solenoid malfunc-

tion

• DTC 33 (P0763): Second solenoid malfunction

• DTC 34 (P0768): Overdrive solenoid malfunction

• DTC 54 (P1751): A/T control relay malfunction

Sensor (The sensor below is determined to be 

normal)

• Input shaft speed sensor

• Output shaft speed sensor

• Transmission range switch

• Torque converter clutch solenoid

• Low-reverse solenoid

• Underdrive solenoid

• Second solenoid

• Overdrive solenoid

• A/T control relay

.

 

 

 

 

 

 

 

Content   ..  541  542  543  544   ..