Mitsubishi Galant 9G. Manual - part 7

 

  Index      Mitsubishi     Mitsubishi Galant 9G - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  5  6  7  8   ..

 

 

Mitsubishi Galant 9G. Manual - part 7

 

 

SWS DIAGNOSIS

TSB Revision

SIMPLIFIED WIRING SYSTEM (SWS)

54B-24

NOTE:  When checking the input signals (off, tail, 
low-beam or high-beam), turn the ignition switch to 
the "ON" position in order to disable the headlight 
automatic shutoff function. However, since the head-
light operation does not depend on the ignition switch 
positions, the scan tool MB991958 (MUT-III Sub 
Assembly) does not display the title "IGNITION 
SWITCH".

For checking item "HEADLIGHT HI", the scan tool 
MB991958 (MUT-III Sub Assembly) displays "OFF" 
on the item No.2 "DIMMER SW" when the headlights 
are at high-beam. Therefore, the scan tool 
MB991958 (MUT-III Sub Assembly) should display 
"ON" momentarily when the dimmer switch is oper-
ated.

HEADLIGHT 
LO

00

Headlight switch

HEADLIGHT SW (COLUMN 
ECU)

ON

03

Passing light 
switch

PASSING SW (COLUMN 
ECU)

OFF

30

Ignition switch 
(IG1)

IG SW (IG1) (ETACS ECU) ON or OFF

35

Headlight 
automatic shutoff 
function

H/L AUTO-CUT (ETACS 
ECU)

OFF

70

Response by the 
front-ECU

FRONT ECU ACK (FRONT 
ECU)

NORMAL ACK

PASSING 
LIGHT

03

Passing light 
switch

PASSING SW (COLUMN 
ECU)

ON

70

Response by the 
front-ECU

FRONT ECU ACK (FRONT 
ECU)

NORMAL ACK or HI-BEAM 
ACK

F.FOG LIGHT

00

Headlight switch

HEADLIGHT SW (COLUMN 
ECU)

ON

36

Front fog light 
switch

F.FOG LIGHT (COLUMN 
ECU)

ON

35

Headlight 
automatic shutoff 
function

H/L AUTO-CUT (ETACS 
ECU)

OFF

30

Ignition switch 
(IG1)

IG SW (IG1) (ETACS ECU) ON or OFF

70

Response by the 
front-ECU

FRONT ECU ACK (FRONT 
ECU)

NORMAL ACK or HI-BEAM 
ACK

TAIL LIGHT

00

Headlight switch

HEADLIGHT SW (COLUMN 
ECU)

OFF

01

Tail light switch

TAILLIGHT SW (COLUMN 
ECU)

ON

03

Passing light 
switch

PASSING SW (COLUMN 
ECU)

OFF

30

Ignition switch 
(IG1)

IG SW (IG1) (ETACS ECU) ON or OFF

35

Headlight 
automatic shutoff 
function

H/L AUTO-CUT (ETACS 
ECU)

OFF

70

Response by the 
front-ECU

FRONT ECU ACK (FRONT 
ECU)

NORMAL ACK

ITEM

ITEM NO. INPUT SIGNAL

DISPLAY ON SCAN TOOL NORMAL CONDITION

SWS DIAGNOSIS

TSB Revision

SIMPLIFIED WIRING SYSTEM (SWS)

54B-25

.

TURN SIGNAL

.

BUZZER

NOTE:  The headlight automatic shutoff function 
operates approximately one second after the lighting 
monitor tone alarm starts sounding, and then the 
tone alarm ceases sounding.

.

ITEM

ITEM NO. INPUT SIGNAL

DISPLAY ON SCAN TOOL NORMAL CONDITION

TURN-SIG.LH

10

Turn-signal light 
switch (RH)

T/S RH SW (COLUMN 
ECU)

OFF

11

Turn-signal light 
switch (LH)

T/S LH SW (COLUMN 
ECU)

ON

30

Ignition switch 
(IG1)

IG SW (IG1) (ETACS ECU) ON

TURN-SIG.RH 10

Turn-signal light 
switch (RH)

T/S RH SW (COLUMN 
ECU)

ON

11

Turn-signal light 
switch (LH)

T/S LH SW (COLUMN 
ECU)

OFF

30

Ignition switch 
(IG1)

IG SW (IG1) (ETACS ECU) ON

ITEM

ITEM NO. INPUT SIGNAL

DISPLAY ON SCAN TOOL NORMAL CONDITION

KEY 
REMND.ALM

30

Ignition switch 
(IG1)

IG SW (IG1) (ETACS ECU)

OFF

32

Front door switch

FRONT DOOR SW (ETACS 
ECU)

ON

43

Tone alarm

BUZZER (ETACS ECU)

ON

LGT 
MONI.ALRM

00

Headlight switch

HEADLIGHT SW (COLUMN 
ECU)

Either is ON

01

Tail light switch

TAILLIGHT SW (COLUMN 
ECU)

30

Ignition switch 
(IG1)

IG SW (IG1) (ETACS ECU)

OFF

32

Front door switch

FRONT DOOR SW (ETACS 
ECU)

ON

35

Headlight 
automatic shutoff 
function

H/L AUTO-CUT (ETACS 
ECU)

OFF

43

Tone alarm

BUZZER (ETACS ECU)

ON

OTHER 
ALARM

30

Ignition switch 
(IG1)

IG SW (IG1) (ETACS ECU)

ON

43

Tone alarm

BUZZER (ETACS ECU)

ON

SWS DIAGNOSIS

TSB Revision

SIMPLIFIED WIRING SYSTEM (SWS)

54B-26

SUNROOF

PULSE CHECK

M1549015100562

1. The input signals (signals other than SWS 

communication line signals), which are 
compatible with the SWS monitor by using the 
scan tool MB991958 (MUT-III Sub Assembly) or 
voltmeter, can be confirmed by the Pulse Check.

2. Use the scan tool MB991958 (MUT-III Sub 

Assembly) or voltmeter to check the following 
input signals.
NOTE:  If a problem is found in the Pulse Check, 
refer to Input Signal Chart 

P.54B-63

.

Switches and their conditions, which are applicable 
for Pulse Check

ITEM

ITEM NO. INPUT SIGNAL

DISPLAY ON SCAN TOOL NORMAL CONDITION

SUNROOF 
OPE.

30

Ignition switch 
(IG1)

IG SW (IG1) (ETACS ECU) ON

72

Response by the 
sunroof-ECU

S/R ECU ACK (SUNROOF 
ECU)

INPUT CHECK (only 
momentarily when switch is 
operated)

INPUT SIGNAL

REQUIREMENTS FOR SOUNDING TONE 
ALARM

Key reminder switch

When the ignition key is pulled out

Hazard warning light switch

When the switch is turned from off to on

Door switches

A door is opened when all the doors are 
closed

Door lock key cylinder switch

When a door is locked or unlocked by a key 
cylinder

Door lock actuators

Move the door lock knob from lock position 
to unlock position or vice versa

Door lock switch (incorporated in the power window main 
switch and front power window sub switch)

When a door is locked or unlocked by a door 
lock switch

Keyless entry transmitter

When the switch is turned from off to on

Interior light loaded signal

Illuminates the interior lights

DIAGNOSTIC TROUBLE CODE CHART

TSB Revision

SIMPLIFIED WIRING SYSTEM (SWS)

54B-27

DIAGNOSTIC TROUBLE CODE CHART

M1549000700461

DIAGNOSTIC TROUBLE CODE PROCEDURES

DTC 001: Trouble in SWS communication line or ETACS-ECU

NOTE: This troubleshooting procedure requires the 
use of scan tool MB991958 and SWS monitor kit 
MB991813. For details on how to use the SWS mon-
itor, refer to "How to use SWS monitor 

P.54B-15

."

CAUTION

If DTC 001 is set in the ETACS-ECU, always diag-
nose the CAN main bus line.

.

TROUBLE JUDGMENT

The ETACS-ECU communicates with the column 
switch, the front-ECU and the sunroof-ECU through 
the SWS communication line. If there is any trouble 
in the SWS communication line and the 
ETACS-ECU, DTC 001 will be set.

.

TECHNICAL DESCRIPTION (COMMENT)

Current trouble

• The wiring harness wire or connectors may have 

loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector, or the 
ETACS-ECU may be defective.

Past trouble

• If DTC 001 is set as past trouble, carry out diag-

nosis with particular emphasis on wiring and con-
nector(s) in the SWS communication line. For 
diagnosis procedures, refer to "How to cope with 
past trouble" (Refer to GROUP 00, How to treat 
past trouble 

P.00-16

).

.

TROUBLESHOOTING HINTS

• The wiring harness or connectors may have 

loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector.

DIAGNOSTIC TROUBLE 
CODE NO.

DESCRIPTION

REFERENCE 
PAGE

001

Trouble in SWS communication line or ETACS-ECU

P.54B-27

002

Trouble in column switch

P.54B-31

003

Trouble in front-ECU

P.54B-34

004

Trouble in sunroof-ECU

P.54B-37

010

Bus Off

P.54B-40

011

Powertrain control module time-out (related to engine)

P.54B-41

012

Powertrain control module time-out (related to A/T)

013

A/C-ECU time-out

P.54B-45

014

Combination meter time-out

P.54B-48

015

Multi center display unit (middle grade type) time-out

P.54B-52

021

Failure information on combination meter

P.54B-55

 

 

 

 

 

 

 

Content   ..  5  6  7  8   ..