Mitsubishi Lancer (4A9 engine). Manual - part 276

 

  Index      Mitsubishi     Mitsubishi Lancer (4A9 engine) 12GS41 & 44S - service repair manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  274  275  276  277   ..

 

 

Mitsubishi Lancer (4A9 engine). Manual - part 276

 

 

TROUBLESHOOTING

CONTROLLER AREA NETWORK (CAN)

54C-128

<CAN_H>

OK: 1 k

Ω or more

(3) Measure the resistance between C-301 ETACS-

ECU connector terminal No.7 and body earth. 
<CAN_L>

OK: 1 k

Ω or more

Q: Is the check result normal?

YES : 

Go to Step 11.

NO : 

Go to Step 2.

STEP 2. Check the wiring harness between C-122 
SRS connector and C-04 joint connector (CAN1) 
for short to earth (resistance measurement).

CAUTION

• Disconnect the negative battery terminal. For 

details refer to .

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.10 and body 
earth.

OK: 1 k

Ω or more

(3) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.21 and body 
earth.

OK: 1 k

Ω or more

Q: Is the check result normal?

YES : 

Go to Step 3.

NO : 

Go to Step 40.

STEP 3. Check the wiring harness between C-60 
heater control unit connector <vehicles without 
A/C> or C-15 A/C-ECU connector <vehicles with 
A/C> and C-04 joint connector (CAN1) for short 
to earth (resistance measurement).

CAUTION

• Disconnect the negative battery terminal. For 

details refer to .

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.8 and body earth. 

<CAN_H>

OK: 1 k

Ω or more

(3) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.19 and body 
earth. <CAN_L>

OK: 1 k

Ω or more

Q: Is the check result normal?

YES : 

Go to Step 4.

NO  : 

Go to Step 41.

STEP 4. Check the wiring harness between C-01 
combination meter connector and C-04 joint 
connector (CAN1) for short to earth (resistance 
measurement).

CAUTION

• Disconnect the negative battery terminal. For 

details refer to .

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.9 and body earth. 
<CAN_H>

OK: 1 k

Ω or more

(3) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.20 and body 
earth. <CAN_L>

OK: 1 k

Ω or more

Q: Is the check result normal?

YES <vehicles without KOS> : 

Go to Step 5.

YES <vehicles with KOS> : 

Go to Step 6.

NO (the check result is not normal.) : 

Go to Step 

42.

STEP 5. Check the wiring harness between C-06 
WCM connector and C-04 joint connector (CAN1) 
for short to earth (resistance measurement).

CAUTION

• Disconnect the negative battery terminal. For 

details refer to .

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Measure the resistance between C-04 joint 

TROUBLESHOOTING

CONTROLLER AREA NETWORK (CAN)

54C-129

connector (CAN1) terminal No.7 and body earth. 
<CAN_H>

OK: 1 k

Ω or more

(3) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.18 and body 
earth. <CAN_L>

OK: 1 k

Ω or more

Q: Is the check result normal?

YES <vehicles with radio and CD player> : 

Go to 

Step 7.

YES <vehicles with MMCS (vehicles for Russia)> : 

Go to Step 8.

YES <vehicles without MMCS and without radio 
and CD player> : 

Go to Step 9.

NO (the check result is not normal.) : 

Go to Step 

43.

STEP 6. Check the wiring harness between C-23 
KOS-ECU connector and C-04 joint connector 
(CAN1) for short to earth (resistance 
measurement).

CAUTION

• Disconnect the negative battery terminal. For 

details refer to .

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.5 and body earth. 
<CAN_H>

OK: 1 k

Ω or more

(3) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.16 and body 
earth. <CAN_L>

OK: 1 k

Ω or more

Q: Is the check result normal?

YES <vehicles with radio and CD player> : 

Go to 

Step 7.

YES <vehicles with MMCS (vehicles for Russia)> : 

Go to Step 8.

YES <vehicles without MMCS and without radio 
and CD player> : 

Go to Step 9.

NO (the check result is not normal.) : 

Go to Step 

44.

STEP 7. Check the wiring harness between C-103 
radio and CD player connector and C-04 joint 
connector (CAN1) for short to earth (resistance 
measurement).

CAUTION

• Disconnect the negative battery terminal. For 

details refer to .

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.6 and body earth. 
<CAN_H>

OK: 1 k

Ω or more

(3) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.17 and body 
earth. <CAN_L>

OK: 1 k

Ω or more

Q: Is the check result normal?

YES : 

Go to Step 10.

NO : 

Go to Step 45.

STEP 8. Check the wiring harness between C-54 
CAN box unit connector and C-04 joint connector 
(CAN1) for short to earth (resistance 
measurement).

CAUTION

• Disconnect the negative battery terminal. For 

details refer to .

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.6 and body earth. 
<CAN_H>

OK: 1 k

Ω or more

(3) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.17 and body 
earth. <CAN_L>

OK: 1 k

Ω or more

Q: Is the check result normal?

YES : 

Go to Step 10.

NO : 

Go to Step 46.

TROUBLESHOOTING

CONTROLLER AREA NETWORK (CAN)

54C-130

STEP 9. Check the wiring harness between C-103 
spare connector (for audio) and C-04 joint 
connector (CAN1) for short to earth (resistance 
measurement).

CAUTION

• Disconnect the negative battery terminal. For 

details refer to .

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.6 and body earth.

OK: 1 k

Ω or more

(3) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.17 and body 
earth.

OK: 1 k

Ω or more

Q: Is the check result normal?

YES : 

Go to Step 10.

NO : 

Repair the wiring harness between C-103 
spare connector (for audio) and C-04 joint 
connector (CAN1).

STEP 10. Check the wiring harness between C-
301 ETACS-ECU connector and C-04 joint 
connector (CAN1) for short to earth (resistance 
measurement).

CAUTION

• Disconnect the negative battery terminal. For 

details refer to .

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

• Strictly observe the specified wiring harness 

repair procedure. For details refer to .

(1) Disconnect ETACS-ECU connector and joint 

connector (CAN1), and measure at the wiring 
harness side.

(2) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.11 and body earth. 
<CAN_H>

OK: 1 k

Ω or more

(3) Measure the resistance between C-04 joint 

connector (CAN1) terminal No.22 and body 

earth. <CAN_L>

OK: 1 k

Ω or more

Q: Is the check result normal?

YES : 

Go to Step 47.

NO : 

Repair the wiring harness between C-301 
ETACS-ECU connector and C-04 joint 
connector (CAN1).

STEP 11. Checking short to power supply 
(voltage measurement)
NOTE: This check determines whether there is a 
short to power supply in the CAN-B bus line. If a fail-
ure is present in either the CAN_H or CAN_L line, 
check the appropriate line only.

CAUTION

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect C-301 ETACS-ECU connector, and 

measure at the wiring harness side.

(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between C-301 ETACS-

ECU connector terminal No.6 and body earth. 
<CAN_H>

OK: 5 V or less

(4) Measure the voltage between C-301 ETACS-

ECU connector terminal No.7 and body earth. 
<CAN_L>

OK: 5 V or less

Q: Is the check result normal?

YES : 

Go to Step 21.

NO : 

Go to Step 12.

STEP 12. Check the wiring harness between C-
122 SRS connector and C-04 joint connector 
(CAN1) for short to power supply (voltage 
measurement).

CAUTION

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between C-04 joint 

connector (CAN1) terminal No.10 and body 

TROUBLESHOOTING

CONTROLLER AREA NETWORK (CAN)

54C-131

earth. <CAN_H>

OK: 5 V or less

(4) Measure the voltage between C-04 joint 

connector (CAN1) terminal No.21 and body 
earth. <CAN_L>

OK: 5 V or less

Q: Is the check result normal?

YES : 

Go to Step 13.

NO : 

Go to Step 40.

STEP 13. Check the wiring harness between C-60 
heater control unit connector <vehicles without 
A/C> or C-15 A/C-ECU connector <vehicles with 
A/C> and C-04 joint connector (CAN1) for short 
to power supply (voltage measurement).

CAUTION

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between C-04 joint 

connector (CAN1) terminal No.8 and body earth. 
<CAN_H>

OK: 5 V or less

(4) Measure the voltage between C-04 joint 

connector (CAN1) terminal No.19 and body 
earth. <CAN_H>

OK: 5 V or less

Q: Is the check result normal?

YES : 

Go to Step 14.

NO : 

Go to Step 41.

STEP 14. Check the wiring harness between C-01 
combination meter connector and C-04 joint 
connector (CAN1) for short to power supply 
(voltage measurement).

CAUTION

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between C-04 joint 

connector (CAN1) terminal No.9 and body earth. 
<CAN_H>

OK: 5 V or less

(4) Measure the voltage between C-04 joint 

connector (CAN1) terminal No.20 and body 
earth. <CAN_L>

OK: 5 V or less

Q: Is the check result normal?

YES <vehicles without KOS> : 

Go to Step 15.

YES <vehicles with KOS> : 

Go to Step 16.

NO (the check result is not normal.) : 

Go to Step 

42.

STEP 15. Check the wiring harness between C-06 
WCM connector and C-04 joint connector (CAN1) 
for short to power supply (voltage 
measurement).

CAUTION

• A digital multimeter should be used. For 

details refer to .

• The test wiring harness should be used. For 

details refer to .

(1) Disconnect joint connector (CAN1), and measure 

at the wiring harness side.

(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between C-04 joint 

connector (CAN1) terminal No.7 and body earth. 
<CAN_H>

OK: 5 V or less

(4) Measure the voltage between C-04 joint 

connector (CAN1) terminal No.18 and body 
earth. <CAN_L>

OK: 5 V or less

Q: Is the check result normal?

YES <vehicles with radio and CD player> : 

Go to 

Step 17.

YES <vehicles with MMCS (vehicles for Russia)> : 

Go to Step 18.

YES <vehicles without MMCS and without radio 
and CD player> : 

Go to Step 19.

NO (the check result is not normal.) : 

Go to Step 

43.

 

 

 

 

 

 

 

Content   ..  274  275  276  277   ..