Mitsubishi Lancer Evolution X. Manual - part 274

 

  Index      Mitsubishi     Mitsubishi Lancer Evolution X GS41EVO - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  272  273  274  275   ..

 

 

Mitsubishi Lancer Evolution X. Manual - part 274

 

 

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-161

STEP 11. Using scan tool MB991958, check data list item 8: 
Manifold Absolute Pressure Sensor.
(1) Turn the ignition switch to the "ON" position.
(2) Set scan tool MB991958 to the data reading mode for item 

8, Manifold Absolute Pressure Sensor.

• When altitude is 0 m (0 foot), 101 kPa (29.8 in.Hg).
• When altitude is 600 m (1,969 feet), 95 kPa (28.1 in.Hg).
• When altitude is 1,200 m (3,937 feet), 88 kPa (26.0 

in.Hg).

• When altitude is 1,800 m (5,906 feet), 81 kPa (23.9 

in.Hg).

(3) Start the engine.

• When the engine is idling, 31 − 45 kPa (9.1 − 13.3 in.Hg).
• When the engine is suddenly revved, manifold absolute 

pressure varies.

(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?

YES : It can be assumed that this malfunction is intermittent. 

Refer to GROUP 00, How to Use 
Troubleshooting/Inspection Service Points − How to 

Cope with Intermittent Malfunctions 

P.00-15

.

NO :  Replace the ECM. When the ECM is replaced, 

register the ID code. Refer to GROUP 42B, ID Code 
Registration Necessity Judgment Table <Vehicles 
with KOS> 

P.42B-11

 or GROUP 42C, ID Codes 

Registration Judgment Table <Vehicles with WCM> 

P.42C-9

. Then go to Step 12.

STEP 12. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to 

Diagnostic Function − OBD-II Drive Cycle − Pattern 6 

P.13A-9

.

(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0107 set?

YES : Retry the troubleshooting.
NO :  The inspection is complete.

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-162

DTC P0108: Manifold Absolute Pressure Circuit High Input

.

AK604115

1

2

3 4 5 6 7 8 9 10 11 12 13 14 15 16

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

3

2

1

AC

MANIFOLD ABSOLUTE
PRESSURE SENSOR

BLUE

3

1

2

MANIFOLD ABSOLUTE PRESSURE SENSOR CIRCUIT

B-09

B-18

(MU802723)

44

45

46

ENGINE
CONTROL
MODULE

YELLO

W

-BLUE

BLA

CK-WHITE

AK704227

Connector: B-09

ECM

B-09 (GR)

AB

AK704238 AB

Manifold absolute
pressure sensor

Connector: B-18

B-18 (B)

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-163

CIRCUIT OPERATION

• A 5-volt voltage is supplied to the manifold abso-

lute pressure sensor power terminal (terminal No. 
3) from ECM (terminal No. 44). The ground termi-
nal (terminal No. 2) is grounded with ECM (termi-
nal No. 46).

• A voltage that is proportional to the intake mani-

fold pressure is sent to the ECM (terminal No. 45) 
from the manifold absolute pressure sensor out-
put terminal (terminal No. 1).

.

TECHNICAL DESCRIPTION

• The manifold absolute pressure sensor outputs a 

voltage which corresponds to the intake manifold 
pressure.

• The ECM checks whether this voltage is within a 

specified range.

.

DESCRIPTIONS OF MONITOR METHODS

Manifold absolute pressure sensor output voltage is 

out of specified range.

.

MONITOR EXECUTION

Continuous

.

MONITOR EXECUTION CONDITIONS 
(Other monitor and Sensor)

Other Monitor (There is no temporary DTC stored 

in memory for the item monitored below)

• Not applicable

Sensor (The sensor below is determined to be 

normal)

• Engine coolant temperature sensor
• Throttle position sensor
• Mass airflow sensor
• Intake air temperature sensor
• Barometric pressure sensor

.

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-164

DTC SET CONDITIONS

Logic Flow Chart

Check Condition

• 8 minutes or more have passed since the engine 

starting sequence was completed, when the 
engine coolant temperature at engine start is 0° C 

(32° F) or lower.

Judgement Criterion

• Manifold absolute pressure sensor output voltage 

has continued to be 4.6 volts [corresponding to a 
manifold absolute pressure of 314 kPa (92.7 
in.Hg)] or higher for 2 seconds.

.

FAIL-SAFE AND BACKUP FUNCTION

• None

.

OBD-II DRIVE CYCLE PATTERN

Refer to Diagnostic Function − OBD-II Drive Cycle − 

Pattern 23 

P.13A-9

.

.

TROUBLESHOOTING HINTS (The most 
likely causes for this code to be set are:)

• Manifold absolute pressure sensor failed.
• Open manifold absolute pressure sensor circuit, 

or connector damage.

• ECM failed. 

Yes

Yes

Yes

Yes

No

No

No

No

Monitoring

conditions

Pressure

< 13kPa (3.8in.Hg)

Pressure

> 314kPa (92.7in.Hg)

Continuous

failure for 2secs

Malfunction

End

Good

Start

AK800582

 

 

 

 

 

 

 

Content   ..  272  273  274  275   ..