Mitsubishi Lancer Evolution 8. Manual - part 128

 

  Index      Mitsubishi     Mitsubishi Lancer Evolution 8 - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  126  127  128  129   ..

 

 

Mitsubishi Lancer Evolution 8. Manual - part 128

 

 

SWS – TROUBLESHOOTING

54B-35

Is door ajar warning set to “Function present” by
adjustment function?

SWS monitor ECU check
• Ignition switch : ON

ETACS-ECU 

OK: “OK” is displayed

SWS monitor service data
(Communications data) ETACS
• Driver’s door : open
Item No. 

Item Name

Normal state

32

Driver door SW RH      ON

OK: Displays normal state

SWS monitor service data
(Communications data) ETACS
• Each door : respectively opened and closed
Item No. 

Item Name

Normal state

38

Security alarm

ON

OK: Displays normal state

SWS monitor service data
ETACS analogue data
• Vehicle speed : Input simulated vehicle speed of
approx. 10 km/h
Item No. 

Item Name

Normal state

03

Vehicle speed sensor

8-10 km/h

OK: Displays normal state

Confirm the trouble symptoms

Transient problem

Set door ajar warning set to “Function present” by
adjustment function

To Inspection procedure A-3 No communication with
ETACS-ECU (see p.54B-28)

To Inspection procedure R-4 “Driver’s door switch signal
not input” (See p.54B-98)

To Inspection procedure R-14 “All door switch signals not
input  (except driver’s door)” (See p.54B-106)

To Inspection procedure R-16 “Vehicle speed signal not
input” (See p.54B-108)

Replace the ETACS-ECU

Inspection Procedure B-3

Door ajar warning function not working correctly

Probable Cause

This function is operated by determining the following input signals in the
ETACS-ECU.
• All door switch  
• Vehicle speed signal

• Fault in all door switch
• Fault in ETACS-ECU
• Fault in harness or connectors

YES

NO

NG

NG

NG

NG

NG

OK

OK

OK

OK

OK

SWS – TROUBLESHOOTING

54B-36

nspection Procedure B-4

Is the turn indicator operating noise function set to
“Function present” by the adjustment function?

SWS monitor ECU check
• Ignition switch : ON
(1)  Column ECU
(2)  ETACS-ECU 
OK: “OK” is displayed for all

SWS monitor service data
(Diagnosis by Function) Turn indicator light : R Turn
indicator 
• Turn indicator light switch : RH
• Ignition switch : ON
Item No. 

Item Name

Normal state

(a) 10

RH turn indicator SW

ON

(b) 30

Ignition SW IG1

ON

OK: All display normal state

SWS monitor service data
(Diagnosis by Function) Turn indicator light : L Turn
indicator 
• Turn indicator light switch : LH
• Ignition switch : ON
Item No. 

Item Name

Normal state

(a) 11

LH turn indicator SW

ON

OK: Displays normal state

Confirm the trouble symptoms 

Transient problem

Set the turn indicator operating noise function to
“Function present” by the adjustment function

To Inspection procedure A-2 No communication with
Column ECU (see p.54B-27)

To Inspection procedure A-3 No communication with
ETACS-ECU (see p.54B-28)

To Inspection procedure R-5 “Column switches Lighting,
Turn indicator light switch) signal not input” (See p.54B-
99)

To Inspection procedure R-2 “Ignition switch (IG1) signal
not input” (See p.54B-96)

To Inspection procedure R-5 “Column switches Lighting,
Turn indicator light switch) signal not input” (See p.54B-
99)

Replace the ETACS-ECU

Turn indicator light operating noise not working correctly

Probable Cause

This function is operated by determining the following input signals in the
ETACS-ECU.
• Turn indicator light switch
• Hazard light switch

• Fault in column switch
• Fault in ETACS-ECU
• Fault in harness or connectors

YES

NO

NG (1)

NG (2)

NG (a)

NG (b)

NG

NG

OK

OK

OK

OK

SWS – TROUBLESHOOTING

54B-37

Is the multi-centre display working normally?

SWS monitor ECU check
(1)  ETACS-ECU 
(2)  Centre display
OK: “OK” is displayed for all

SWS monitor service data
(Diagnosis by Function) Buzzer : Display buzzer
• Ignition switch : ON
• Radio memory operation has been performed
Item No. 

Item Name

Normal state

(a) 60

beep data

ON (2kHz)

(b) 43

Buzzer

OFF

OK: All display normal state

Confirm the trouble symptoms 

Transient problem

Check the multi-centre display (See Chap. 54A –
MMCS*)

To Inspection procedure A-3 No communication with
ETACS-ECU (see p.54B-28)

To Inspection procedure A-7 No communication with
Multi-centre display (see p.54B-32)

To Inspection procedure R-10 “Respective switch signals
of multi-centre display not input” (See p.54B-103)

Replace the ETACS-ECU 

Replace the ETACS-ECU

Inspection Procedure B-5

Note :
(1) When performing the SWS monitor service data check, confirm at the same time that the 60 beep data state changes

momentarily from “OFF” to the normal state when the image operating switch is activated. 

(2) *: See ’00-5 Lancer Cedia Servicing Manual (No. 1036K00)

Multi-centre display operating noise function not working correctly

Probable Cause

A buzzer sounds when the ETACS-ECU receives a sound request signal
from the multi-centre display.
If this function does not work correctly, then this is probably due to an
abnormality in the communications circuit, a fault in the multi-centre
display, or a fault in the ETACS-ECU.

• Fault in multi-centre display
• Fault in ETACS-ECU
• Fault in harness or connectors

OK

NG

NG (1)

NG (a)

NG (b)

NG 

NG (2)

OK

OK

OK

SWS – TROUBLESHOOTING

54B-38

Inspection Procedure C-1

SWS monitor ECU check
• Ignition switch : OFF

ETACS-ECU 

OK: “OK” is displayed for all

Check connector E-03

Check driver’s door lock actuator (See Chap. 42 Doors)

Check connectors C-224, C-211, C-32

Check the harness between the ETACS-ECU and the
fusible link (1)

Confirm the trouble symptoms 

Transient problem

To Inspection procedure A-3 No communication with
ETACS-ECU (see p.54B-28)

To Inspection procedure R-15 Driver’s door lock actuator
signal not input (See p.54B-107)

Replace the ETACS-ECU

SWS monitor service data
ETACS switch data
• Driver’s door : Unlock 

lock

Item No. 

Item Name

Normal state

(1) 21

Dr Door lock SW

OFF 

ON

(2) 22

Dr Door unlock SW

ON 

OFF

OK: All display normal state

Central door locking not working at all

Probable Cause

The ETACS-ECU locks or unlocks all the doors by activating all of the door
lock actuators, when there is a change in the input signal from the driver’s door
lock actuator.
If this function does not work properly, then there is probably a fault in the
driver’s door lock actuators or a fault in the ETACS-ECU.

• Fault in driver’s door lock actuator
• Fault in ETACS-ECU
• Fault in harness or connectors

OK

OK

OK

OK

OK

OK

OK

NG

Repair

Repair

Replace

Repair

NG

NG

NG

NG

NG

NG

 

 

 

 

 

 

 

Content   ..  126  127  128  129   ..