Jeep XJ. Manual - part 885

 

  Index      Jeep     Jeep XJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  883  884  885  886   ..

 

 

Jeep XJ. Manual - part 885

 

 

7.0

DIAGNOSTIC INFORMATION AND

PROCEDURES

9

Symptom:

*NO RESPONSE FROM TRANSMISSION CONTROL MODULE

POSSIBLE CAUSES

GROUND CIRCUIT OPEN

FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN

CCD BUS (+) CIRCUIT OPEN

CCD BUS (-) CIRCUIT OPEN

TRANSMISSION CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure the DRB can establish communications with the PCM before
beginning.
Turn the ignition off.
Disconnect the TCM harness connector.
Measure the resistance between ground and the ground circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

2

No

Repair the Ground circuit for an open.
Perform AW4 TRANS VERIFICATION TEST-VER1.

2

NOTE: Ensure the DRB can establish communications with the PCM before
beginning.
Turn the ignition off.
Disconnect the TCM harness connector.
Turn the ignition on.
Measure the voltage of the Fused Ignition Switch Output circuit.
Is the voltage above 10.0 volts?

All

Yes

Go To

3

No

Repair the Fused Ignition Switch Output circuit for an open.
Perform AW4 TRANS VERIFICATION TEST-VER1.

3

NOTE: Ensure the DRB can establish communications with the PCM before
beginning.
Turn the ignition off.
Disconnect the TCM harness connector.
Connect a jumper wire between the CCD Bus (+) circuit and ground.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: SHORT TO GROUND?

All

Yes

Go To

4

No

Repair the CCD Bus (+) circuit for an open.
Perform AW4 TRANS VERIFICATION TEST-VER1.

10

COMMUNICATION

TEST

ACTION

APPLICABILITY

4

NOTE: Ensure the DRB can establish communications with the PCM before
beginning.
Turn the ignition off.
Disconnect the TCM harness connector.
Connect a jumper wire between the CCD Bus (-) circuit and ground.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: SHORT TO GROUND?

All

Yes

Go To

5

No

Repair the CCD Bus (-) circuit for an open.
Perform AW4 TRANS VERIFICATION TEST-VER1.

5

If there are no possible causes remaining, view repair.

All

Repair

Replace the Transmission Control Module.
Perform AW4 TRANS VERIFICATION TEST-VER1.

11

COMMUNICATION

*NO RESPONSE FROM TRANSMISSION CONTROL MODULE —

Continued

Symptom:

P0122-THROTTLE POSITION SENSOR

When Monitored and Set Condition:

P0122-THROTTLE POSITION SENSOR

When Monitored:

Continuously with the ignition key on.

Set Condition:

The Throttle Position Sensor Signal circuit is out of range for 7 seconds or

the Sensor Ground circuit is open or shorted to voltage for 7 seconds.

POSSIBLE CAUSES

TPS DTC’S PRESENT IN THE PCM

INTERMITTENT WIRING AND/OR CONNECTORS

TPS SIGNAL CIRCUIT OPEN

TPS SENSOR GROUND CIRCUIT OPEN TO TCM

TPS SIGNAL CIRCUIT SHORTED TO GROUND

TPS SENSOR GROUND CIRCUIT SHORTED TO VOLTAGE

TPS SIGNAL CIRCUIT SHORTED TO VOLTAGE

TCM-TPS CIRCUIT

TEST

ACTION

APPLICABILITY

1

NOTE: Always perform diagnostics with a fully charged battery to avoid
diagnosing false symptoms.
NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Verify the brake switch input to the TCM is working correctly.
Perform the shift lever position test and adjust the linkage if necessary.
Test drive vehicle to verify customer complaint.
With the DRBIII

t, read the PCM DTC’s. Check and repair all PCM DTC’s before

performing transmission diagnostics.
With the DRBIII

t, read the TCM DTC’s.

Note: Check 1 trip failures and diagnose them as DTC’s (Hard codes)
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to symptom diagnosis.

All

Continue

Go To

2

12

TRANSMISSION

 

 

 

 

 

 

 

Content   ..  883  884  885  886   ..