Jeep XJ. Manual - part 623

 

  Index      Jeep     Jeep XJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  621  622  623  624   ..

 

 

Jeep XJ. Manual - part 623

 

 

TEST

ACTION

APPLICABILITY

3

WARNING: KEEP CLEAR OF THE ENGINE’S MOVING PARTS.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform ROAD TEST VERIFICATION - VER-2.

No

Test Complete.

4

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Message Center harness connector.
Measure the resistance between ground and the Glow Plug Lamp Control circuit.
Is the resistance above 100 kohms?

All

Yes

Go To

5

No

Repair the Glow Plug Lamp Control circuit for a short to ground.
Perform ROAD TEST VERIFICATION - VER-2.

5

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Message Center harness connector.
Measure the resistance of the Glow Plug Lamp Control circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

6

No

Repair the Glow Plug Lamp Control circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

6

NOTE: Ensure the Message Center harness connector is connected.
Turn the ignition off.
Disconnect the ECM harness connectors.
Turn the ignition on.
Connect a jumper wire between ground and the Glow Plug Lamp Control circuit in
ECM harness connector C1.
Did the Glow Plug Lamp illuminate?

All

Yes

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

7

144

DRIVEABILITY - DIESEL

P1645-GLOW DISPLAY SHORT CIRCUIT —

Continued

TEST

ACTION

APPLICABILITY

7

Turn the ignition off.
Remove and check the Glow Plug Lamp bulb from the Instrument Cluster.
Is the bulb OK?

All

Yes

Replace the Message Center.
Perform ROAD TEST VERIFICATION - VER-2.

No

Replace the Glow Plug Lamp bulb.
Perform ROAD TEST VERIFICATION - VER-2.

145

DRIVEABILITY - DIESEL

P1645-GLOW DISPLAY SHORT CIRCUIT —

Continued

Symptom:

P1660-REDUNDANT EMERG. STOP PLAUSIBILITY IN AFTER-RUN

When Monitored and Set Condition:

P1660-REDUNDANT EMERG. STOP PLAUSIBILITY IN AFTER-RUN

When Monitored:

During after-run, when the engine speed is below 800 RPM and vehicle

speed is below 2.5 MPH.

Set Condition:

The fuel shutdown solenoid is turned off and engine speed does not drop

below 500 RPM.

POSSIBLE CAUSES

INTERMITTENT CONDITION

FUEL SHUTDOWN SOLENOID CONTROL CIRCUIT SHORTED TO VOLTAGE

FUEL SHUTDOWN SOLENOID (FUEL INJECTION PUMP) SHORTED INTERNALLY

INTERNAL FUEL INJECTION PUMP TEST

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, erase ECM DTCs.
Start and stop the engine several times, pausing for 10 seconds at key off each time.
Turn the ignition on.
With the DRB, read ECM DTCs.
Did this DTC reset?

All

Yes

Go To

2

No

Go To

5

2

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Fuel Injection Pump harness connector.
Remove the ASD/Diesel Power Relay from the PDC.
Connect a jumper wire between cavity 30 and cavity 87 of the ASD/Diesel Power
Relay connector.
Turn the ignition on.
Measure the voltage on the Fuel Shutdown Solenoid Control circuit.
Is the voltage below 0.5 volt?

All

Yes

Go To

3

No

Repair the Fuel Shutdown Solenoid Control circuit for a short to
voltage.
Perform ROAD TEST VERIFICATION - VER-2.

NOTE: Remove the jumper wire from the ASD/Diesel Power Relay connec-
tor, reinstall the ASD/Diesel Power Relay in the PDC, and reconnect the
ECM harness connectors.

146

DRIVEABILITY - DIESEL

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Fuel Injection Pump harness connector.
Turn the ignition on.
With the DRB, actuate the Fuel Shutdown Solenoid.
Measure the voltage on the Fuel Shutdown Solenoid Control circuit.
Does the voltage cycle from B+ to below 1.0 volt?

All

Yes

Replace the Fuel Injection Pump in accordance with the Service
Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

4

4

Disconnect the Fuel Injection Pump harness connector.
Measure the resistance between the following cavities in the Fuel Injection Pump
connector (fuel pump side):
Cavity 1 to cavities 4, 5, 6, 7, 8, 9, and 10.
Cavity 4 to cavities 5, 6, 7, 8, 9, and 10.
Cavity 5 to cavities 6, 7, 8, and 9.
Cavity 7 to cavities 6, 8, 9, and 10.
Cavity 8 to cavities 6 and 10.
NOTE: The resistance should be above 100 ohms for all measurements.
Is the resistance above 100 ohms for each of the measurements?

All

Yes

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Replace the Fuel Injection Pump in accordance with the Service
Information.
Perform ROAD TEST VERIFICATION - VER-2.

5

WARNING: KEEP CLEAR OF THE ENGINE’S MOVING PARTS.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform ROAD TEST VERIFICATION - VER-2.

No

Test Complete.

147

DRIVEABILITY - DIESEL

P1660-REDUNDANT EMERG. STOP PLAUSIBILITY IN AFTER-RUN —

Continued

 

 

 

 

 

 

 

Content   ..  621  622  623  624   ..