Jeep XJ. Manual - part 543

 

  Index      Jeep     Jeep XJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  541  542  543  544   ..

 

 

Jeep XJ. Manual - part 543

 

 

TEST

ACTION

APPLICABILITY

9

Turn the ignition off.
Remove the Instrument Cluster.
Measure the resistance of the CCD Bus (+) and the CCD Bus (-) circuits between the
Instrument Cluster C2 harness connector and the DLC.
Is the resistance below 5.0 ohms on both circuits?

All

Yes

Go To

10

No

Repair the CCD Bus (+) or CCD Bus (-) circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

10

Turn the ignition off.
Disconnect the negative battery cable.
Remove the Instrument Cluster.
Measure the resistance between ground and the CCD Bus (+) and the CCD Bus (-)
circuits.
Is the resistance below 1000.0 ohms on either circuit?

All

Yes

Repair the CCD Bus (+) or CCD Bus (-) circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

11

11

If there are no possible causes remaining, view repair.

All

Repair

Replace the Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.

52

COMMUNICATION

*BUS BIAS LEVEL TOO HIGH —

Continued

Symptom:

*BUS BIAS LEVEL TOO LOW

POSSIBLE CAUSES

DRB OR DRB CABLE

POWERTRAIN CONTROL MODULE

AIRBAG CONTROL MODULE

SENTRY KEY IMMOBILIZER MODULE (IF EQUIPPED)

REMOTE KEYLESS ENTRY MODULE (IF EQUIPPED)

OVERHEAD CONSOLE (IF EQUIPPED)

TRANSMISSION CONTROL MODULE (IF EQUIPPED)

GROUND CIRCUIT OPEN

CCD BUS (+) OR BUS (-) CIRCUIT OPEN

CCD BUS (+) OR BUS (-) CIRCUIT SHORTED TO GROUND

INSTRUMENT CLUSTER

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
Disconnect the DRB from the Data Link Connector (DLC).
Measure the voltage of the CCD Bus (+) and the CCD Bus (-) circuits in the DLC.
Is the voltage between 1.8 and 2.8 volts on both circuits?

All

Yes

Repair/Replace the DRB or DRB cable as necessary.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Turn the ignition off.
Disconnect the PCM C3 harness connector.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: BUS OPERATIONAL?

All

Yes

Replace the Powertrain Control Module.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

3

3

TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND WAIT TWO
MINUTES BEFORE PROCEEDING.
Disconnect the ACM harness connector.
TURN THE IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: BUS OPERATIONAL?

All

Yes

Replace the Airbag Control Module.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

4

53

COMMUNICATION

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the SKIM harness connector.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: BUS OPERATIONAL?

All

Yes

Replace the Sentry Key Immobilizer Module.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

5

5

Turn the ignition off.
Disconnect the RKE Module harness connector.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: BUS OPERATIONAL?

All

Yes

Replace the Remote Keyless Entry Module.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

6

6

Turn the ignition off.
Disconnect the Compass Mini Trip Computer (overhead console) harness connector.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: BUS OPERATIONAL?

All

Yes

Replace the Compass Mini Trip Computer (Overhead Console).
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

7

7

Turn the ignition off.
Disconnect the TCM harness connector.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: BUS OPERATIONAL?

All

Yes

Replace the Transmission Control Module.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

8

8

Turn the ignition off.
Disconnect the Instrument Cluster C1 harness connector.
NOTE: Ensure the interior lights are off.
Measure the resistance between ground and the ground circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

9

No

Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

54

COMMUNICATION

*BUS BIAS LEVEL TOO LOW —

Continued

TEST

ACTION

APPLICABILITY

9

Turn the ignition off.
Remove the Instrument Cluster.
Measure the resistance of the CCD Bus (+) and the CCD Bus (-) circuits between the
Instrument Cluster C2 harness connector and the DLC.
Is the resistance below 5.0 ohms on both circuits?

All

Yes

Go To

10

No

Repair the CCD Bus (+) or CCD Bus (-) circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

10

Turn the ignition off.
Disconnect the negative battery cable.
Remove the Instrument Cluster.
Measure the resistance between ground and the CCD Bus (+) and the CCD Bus (-)
circuits.
Is the resistance below 1000.0 ohms on either circuit?

All

Yes

Repair the CCD Bus (+) or CCD Bus (-) circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

11

11

If there are no possible causes remaining, view repair.

All

Repair

Replace the Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.

55

COMMUNICATION

*BUS BIAS LEVEL TOO LOW —

Continued

 

 

 

 

 

 

 

Content   ..  541  542  543  544   ..