Jeep Wrangler TJ. Manual - part 150

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  148  149  150  151   ..

 

 

Jeep Wrangler TJ. Manual - part 150

 

 

TEST

ACTION

APPLICABILITY

7

Turn the ignition off to the lock position.
Disconnect the Input Speed Sensor harness connector.
Disconnect the TCM harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Measure the voltage of the Input Speed Sensor Signal circuit in the TCM harness
connector.
Is the voltage above 0.5 volts?

All

Yes

→ Repair the Input Speed Sensor Signal circuit for a short to

voltage.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Go To 8

8

Turn the ignition off to the lock position.
Disconnect the TCM harness connector.
Disconnect the Input Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Speed Sensor Ground circuit from the TCM harness
connector to the Input Speed Sensor harness connector.
Is the resistance above 5.0 ohms?

All

Yes

→ Repair the Speed Sensor Ground circuit for an open.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Go To 9

9

Turn the ignition off to the lock position.
Disconnect the TCM harness connector.
Disconnect the TRS harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Measure the voltage of the Speed Sensor Ground circuit in the TCM harness
connector.
Is the voltage above 0.5 volts?

All

Yes

→ Repair the Speed Sensor Ground circuit for a short to voltage.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Go To 10

10

Using the schematics as a guide, inspect the wiring and connectors. Repair as
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIII

t PERFORM QUICK LEARN.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

325

TRANSMISSION - 42RLE

P0715-INPUT SPEED SENSOR ERROR —

Continued

TEST

ACTION

APPLICABILITY

11

The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Test Complete.

326

TRANSMISSION - 42RLE

P0715-INPUT SPEED SENSOR ERROR —

Continued

Symptom:

P0720-OUTPUT SPEED SENSOR ERROR

When Monitored and Set Condition:

P0720-OUTPUT SPEED SENSOR ERROR

When Monitored:

The transmission gear ratio is monitored continuously while the

transmission is in gear.

Set Condition:

If there is an excessive change in output RPM in any gear.

POSSIBLE CAUSES

INTERMITTENT WIRING AND CONNECTORS

OUTPUT SPEED SENSOR SIGNAL CIRCUIT OPEN

SPEED SENSOR GROUND CIRCUIT OPEN

OUTPUT SPEED SENSOR SIGNAL CIRCUIT SHORT TO GROUND

OUTPUT SPEED SENSOR SIGNAL CIRCUIT SHORT TO VOLTAGE

SPEED SENSOR GROUND CIRCUIT SHORT TO VOLTAGE

OUTPUT SPEED SENSOR ERROR

TRANSMISSION CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many Transmission problems. If
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing Transmission Symptom Diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

327

TRANSMISSION - 42RLE

TEST

ACTION

APPLICABILITY

2

Start the engine in park.
Raise the drive wheels off of the ground.
WARNING: PROPERLY SUPPORT THE VEHICLE.
Place transmission in drive, release foot from brake.
WARNING: BE SURE TO KEEP HANDS AND FEET CLEAR OF ROTATING
WHEELS.
Note: The drive wheels must be turning at this point.
With the DRBIII

t, read the Output RPM

Is the Output RPM below 100 RPM?

All

Yes

→ Go To 3

No

→ Go To 11

3

Turn the ignition off to the lock position.
CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
With the Transmission Simulator, set the

9Input/Output Speed9 switch to 9ON9 and

the rotary switch to the

93000/12509 position.

With the DRBIII

t, read the Input RPM and Output RPM.

Does the Input RPM read 3000 and the Output RPM read 1250 ± 50 RPM?

All

Yes

→ Go To 4

No

→ Go To 5

4

If there are no possible causes remaining, view repair.

All

Repair

Replace the Output Speed Sensor per the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

5

Turn the ignition off to the lock position.
Disconnect the TCM harness connector.
Disconnect the Output Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Output Speed Sensor Signal circuit from the TCM
harness connector to the Output Speed Sensor harness connector.
Is the resistance above 5.0 ohms?

All

Yes

→ Repair the Output Speed Sensor Signal circuit for an open.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Go To 6

328

TRANSMISSION - 42RLE

P0720-OUTPUT SPEED SENSOR ERROR —

Continued

 

 

 

 

 

 

 

Content   ..  148  149  150  151   ..