Jeep Wrangler TJ. Manual - part 39

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  37  38  39  40   ..

 

 

Jeep Wrangler TJ. Manual - part 39

 

 

Symptom:

*BRAKE WARNING INDICATOR INOPERATIVE

POSSIBLE CAUSES

BRAKE WARNING INDICATOR CIRCUIT SHORT TO VOLTAGE

BRAKE WARNING INDICATOR CIRCUIT OPEN

BRAKE WARNING INDICATOR SWITCH

PARK BRAKE SWITCH

INSTRUMENT CLUSTER

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Perform the Instrument Cluster Self Test.
Did the Brake Warning Indicator illuminate during the Self Test?

All

Yes

→ Go To 2

No

→ Replace the Instrument Cluster in accordance with the Service

Information.
Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Disconnect the Instrument Cluster C2 harness connector.
Check connectors - Clean/repair as necessary.
Measure the voltage between the Brake Warning Indicator circuit and ground.
Is there any voltage present?

All

Yes

→ Repair the Brake Warning Indicator circuit for a short to voltage.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 3

3

NOTE: Ensure that the Instrument Cluster harness connector is connected.
Turn the ignition off.
Disconnect the Brake Warning Indicator Switch (Pressure Switch) harness connec-
tor.
Connect a jumper wire between cavity 1 and cavity 2.
Disconnect the Park Brake Switch harness connector.
Connect a jumper wire between the Brake Warning Indicator circuit and ground.
Turn the ignition on and observe the Brake Warning Indicator.
Does the Brake Warning Indicator illuminate?

All

Yes

→ Replace the Park Brake Switch in accordance with the Service

Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 4

153

INSTRUMENT CLUSTER

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the Instrument Cluster C2 harness connector.
Disconnect the Park Brake Switch harness connector.
Disconnect the Brake Warning Indicator Switch harness connector.
Connect a jumper wire between cavity 1 and cavity 2.
Measure the resistance of the Brake Warning Indicator circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Replace the Brake Warning Indicator Switch in accordance with

the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Repair the Brake Warning Indicator circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

154

INSTRUMENT CLUSTER

*BRAKE WARNING INDICATOR INOPERATIVE —

Continued

Symptom:

*FOG LAMP INDICATOR INOPERATIVE - DOMESTIC

POSSIBLE CAUSES

FOG LAMP INDICATOR CIRCUIT OPEN

INSTRUMENT CLUSTER

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure that the Fog Lamps operate properly. If not, refer to EXTE-
RIOR LIGHTING in the Service Information.
NOTE: The Headlamps must be on Low Beam for indicator to operate.
Turn the ignition off.
Disconnect the Instrument Cluster.
Check connectors - Clean/repair as necessary.
Turn the Headlamps on and actuate the Fog Lamps.
Using a 12-volt test light connected to ground, check the Fog Lamp Indicator circuit.
Does the test light illuminate brightly?

All

Yes

→ Replace the Instrument Cluster in accordance with the Service

Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Repair the Fog Lamp Indicator circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

155

INSTRUMENT CLUSTER

Symptom:

*HIGH BEAM INDICATOR INOPERATIVE

POSSIBLE CAUSES

HIGH BEAM INDICATOR CIRCUIT OPEN

INDICATOR BULB

INSTRUMENT CLUSTER

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure that the Headlamp High Beams operate properly. If not, refer
to the Exterior Lighting Service Information.
Turn the ignition off.
Disconnect the Instrument Cluster C1 harness connector.
Check connectors - Clean/repair as necessary.
Turn the Headlamps on and actuate the High Beams.
NOTE: Ensure that the Fog Lamps are not actuated (Domestic vehicles
only).
Using a 12-volt test light connected to ground, back probe the High Beam Indicator
circuit.
Does the test light illuminate brightly?

All

Yes

→ Go To 2

No

→ Repair the Dimmer Switch High Beam Output circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Disconnect the Instrument Cluster.
Check connectors - Clean/repair as necessary.
Remove and inspect the High Beam Indicator bulb.
Is the indicator bulb filament open?

All

Yes

→ Replace the High Beam Indicator Bulb in accordance with the

Service Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Instrument Cluster in accordance with the Service

Information.
Perform BODY VERIFICATION TEST - VER 1.

156

INSTRUMENT CLUSTER

 

 

 

 

 

 

 

Content   ..  37  38  39  40   ..