Jeep Wrangler TJ. Manual - part 36

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  34  35  36  37   ..

 

 

Jeep Wrangler TJ. Manual - part 36

 

 

Symptom:

*4WD INDICATOR INOPERATIVE

POSSIBLE CAUSES

INTERMITTENT CONDITION

TRANSFER CASE SWITCH - EXCEPT OFF-ROAD PACKAGE

4WD INDICATOR CIRCUIT OPEN

TRANSFER CASE SWITCH GROUND CIRCUIT OPEN - EXCEPT OFF-ROAD PACKAGE

TRANSFER CASE SWITCH - OFF-ROAD PACKAGE

TRANSFER CASE POSITION SENSOR INPUT CIRCUIT OPEN

TRANSFER CASE SWITCH GROUND CIRCUIT OPEN - OFF-ROAD PACKAGE

INSTRUMENT CLUSTER - EXCEPT OFF-ROAD PACKAGE

INSTRUMENT CLUSTER - OFF-ROAD PACKAGE

TEST

ACTION

APPLICABILITY

1

Is vehicle equipped with the optional Off-Road Package?

All

Yes

→ Go To 2

No

→ Go To 6

2

Perform the Instrument Cluster self-test.
Turn the ignition off.
Press and hold the Trip Reset button.
Turn the ignition on.
Observe the 4WD indicator during the self-test.
NOTE: The Instrument Cluster self-test can be initiated using the DRBIII

t.

Did the 4WD indicator illuminate during the self-test?

All

Yes

→ Go To 3

No

→ Replace and configure the Instrument Cluster in accordance with

the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

3

Turn the ignition on, Transfer Case Shift Lever in 2H.
With the DRBIII

t in Inputs/Outputs, read the 4WD Switch state.

Place the Transfer Case Shift Lever in 4H or 4L while observing the 4WD Switch
State.
Did the Does the DRBIII

t display 4H or 4L?

All

Yes

→ The condition is not present at this time. Monitor DRBIIIt

parameters while wiggling the related wire harness. Refer to any
Technical Service Bulletins (TSB) that may apply. Visually in-
spect the related wiring harness and connector terminals.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 4

141

INSTRUMENT CLUSTER

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the Transfer Case Switch harness connector.
Connect a jumper wire between cavity 1 and cavity 2.
Turn the ignition on.
With the DRBIII

t, read the 4WD Switch input.

Does the DRBIII

t display 9Closed?9

All

Yes

→ Replace the Transfer Case Switch in accordance with the Service

Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 5

5

Turn the ignition off.
Disconnect the Transfer Case Switch harness connector.
Disconnect the PCM C1 harness connector.
Measure the resistance of the Transfer Case Position Sensor Input circuit between
the T/Case Switch connector and the PCM C1 connector.
Is the resistance above 5.0 ohms?

All

Yes

→ Repair the Transfer Case Position Sensor Input circuit for an

open.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Repair the Transfer Case Switch Ground circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

6

Turn the ignition on.
With the DRBIII

t, select Body, MIC, then Inputs/Outputs.

Move the transfer case shift lever from the 2H to the 4H or 4L position.
Does the DRBIII

t display 4WD Switch 9Closed9 with the shift lever in the 4H or 4L

position?

All

Yes

→ Replace and configure the Instrument Cluster in accordance with

the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 7

7

Turn the ignition off.
Disconnect the Transfer Case Switch harness connector.
Connect a jumper wire between cavity A and cavity B.
Turn the ignition on.
With the DRBIII

t, read the 4WD Switch input.

Does the DRBIII

t display 9Closed9.

All

Yes

→ Replace the Transfer Case Switch in accordance with the Service

Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 8

142

INSTRUMENT CLUSTER

*4WD INDICATOR INOPERATIVE —

Continued

TEST

ACTION

APPLICABILITY

8

Turn the ignition off.
Disconnect the Transfer Case Switch harness connector.
Connect a jumper wire between the 4WD Indicator circuit and ground.
Turn the ignition on.
With the DRBIII

t, read the 4WD Switch state.

Does the DRBIII

t display 9Closed9?

All

Yes

→ Go To 9

No

→ Repair the 4WD Indicator circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

9

Turn the ignition off.
Disconnect the Transfer Case Switch harness connector.
Measure the resistance between ground and the Transfer Case Switch Ground
circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ The condition is not present at this time. Monitor DRBIIIt

parameters while wiggling the related wire harness. Refer to any
Technical Service Bulletins (TSB) that may apply. Visually in-
spect the related wiring harness and connector terminals.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Repair the Transfer Case Switch Ground circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

143

INSTRUMENT CLUSTER

*4WD INDICATOR INOPERATIVE —

Continued

Symptom:

*ABS INDICATOR INOPERATIVE

POSSIBLE CAUSES

ABS DTC

INSTRUMENT CLUSTER

TEST

ACTION

APPLICABILITY

1

NOTE: The Instrument Cluster ABS Indicator will not illuminate during the
cluster Self Test. The indicator is controlled by PCI Bus messages received
from the CAB.
NOTE: The CAB will command the ABS Indicator on when the ignition is
cycled to the Run/Start position.
With the DRBIII

t, read DTCs.

Does the DRBIII

t display any ABS DTCs?

All

Yes

→ Refer to the Anti-Lock Brake System category and perform the

appropriate symptom.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Instrument Cluster in accordance with the Service

Information.
Perform BODY VERIFICATION TEST - VER 1.

144

INSTRUMENT CLUSTER

 

 

 

 

 

 

 

Content   ..  34  35  36  37   ..