Jeep Wrangler TJ. Manual - part 33

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  31  32  33  34   ..

 

 

Jeep Wrangler TJ. Manual - part 33

 

 

TEST

ACTION

APPLICABILITY

9

Turn the ignition off.
Disconnect the Instrument Cluster C2 connector.
Disconnect the Rear Window Defogger Switch connector.
Turn the ignition on.
Measure voltage between the Rear Window Defogger Switch Sense Circuit and
ground.
Is any voltage present?

All

Yes

→ Repair the Rear Window Switch Sense Circuit for a short to

voltage condition.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 10

10

Turn the ignition off.
Disconnect the Instrument Cluster C2 connector.
Disconnect the Rear Window Defogger Switch connector.
Measure resistance between ground and the Rear Window Defogger Switch Sense
Circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the Rear Window Defogger Switch Sense Circuit for a

short to ground condition.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 11

11

Turn the ignition off.
Disconnect the Instrument Cluster C2 connector.
Disconnect the Rear Window Defogger Switch.
Measure resistance of the Rear Window Defogger Switch Sense circuit from the
Instrument Cluster C2 connector to the Defogger switch connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 12

No

→ Repair the Rear Window Defogger Switch Sense Circuit for an

open condition.
Perform BODY VERIFICATION TEST - VER 1.

12

Turn the ignition off.
Reinstall the Rear Window Defogger Relay.
Reconnect the Instrument Cluster C2 connector.
Disconnect the Rear Window Defogger Switch connector.
Turn the ignition on.
Connect a jumper wire between the Rear Window Defogger Switch Sense circuit in
the Defogger Switch connector to ground and listen for the relay to click.
Does the Defogger Relay click?

All

Yes

→ Replace the Rear Window Defogger Switch.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Instrument Cluster.

Perform BODY VERIFICATION TEST - VER 1.

129

ELECTRICALLY HEATED SYSTEMS

*REAR WINDOW DEFOGGER INOPERATIVE —

Continued

Symptom:

*REAR WINDOW DEFOGGER SWITCH INDICATOR LAMP INOP-
ERATIVE

POSSIBLE CAUSES

FUSED REAR WINDOW DEFOGGER RELAY OUTPUT CKT SHORTED TO GROUND

FUSE BLOCK FUSE #17

FUSED REAR WINDOW DEFOGGER RELAY OUTPUT CKT OPEN

DEFOGGER SWITCH

TEST

ACTION

APPLICABILITY

1

Inspect Fuse Block fuse #17.
Is Fuse Block fuse #17 open?

All

Yes

→ Go To 2

No

→ Go To 3

2

Turn the ignition off.
Disconnect the Rear Defogger Switch.
Measure resistance of the Fused Rear Window Defogger Relay Output circuit to
ground.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the Fused Rear Window Defogger Relay Output circuit for

a short to ground condition.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace Fuse Block fuse #17.

Perform BODY VERIFICATION TEST - VER 1.

3

Turn the ignition off.
Disconnect the Rear Defogger Switch.
Remove the Rear Window Defogger Relay.
Ensure that Fuse Block fuse #17 is installed.
Measure resistance of the Fused Rear Window Defogger Relay Output circuit from
the relay output terminal to the Defogger Switch connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Replace the Rear Window Defogger Switch.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Repair the Fused Rear Window Defogger Relay Output circuit for

an open condition.
Perform BODY VERIFICATION TEST - VER 1.

130

ELECTRICALLY HEATED SYSTEMS

Symptom:

ACM MESSAGE NOT REC’D BY MIC

When Monitored and Set Condition:

ACM MESSAGE NOT REC’D BY MIC

When Monitored:

With the ignition in the Run/Start position, Instrument Cluster in

power-up state.

Set Condition:

The Instrument Cluster detects loss of communication with the Air Bag

Control Module (ACM).

POSSIBLE CAUSES

ACM MESSAGE NOT RECEIVED

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
NOTE: Ensure the Instrument Cluster communicates on the PCI Bus.
With the DRBIII

t, select Body, Electro/Mech Cluster, then read DTCs.

Does the DRBIII

t display ACM Message Not Rec’d by MIC?

All

Yes

→ Refer to the COMMUNICATION category and perform the ap-

propriate symptom.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Test Complete.

131

INSTRUMENT CLUSTER

Symptom:

AIR BAG LAMP CIRCUIT OPEN

When Monitored and Set Condition:

AIR BAG LAMP CIRCUIT OPEN

When Monitored:

With the ignition in the Run/Start position, Instrument Cluster in

power-up state.

Set Condition:

The Instrument Cluster performs an indicator check when the indicator is

commanded on or off by the ACM. If an open lamp failure is detected, the Cluster sends this
meesage to the ACM.

POSSIBLE CAUSES

INSTRUMENT CLUSTER

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
NOTE: Ensure the Instrument Cluster and the Air Bag Control Module
communicate on the PCI Bus.
NOTE: The Airbag indicator can only be turned on or off by the ACM. The
Instrument Cluster reports the indicator status to the ACM on the PCI Bus.
With the DRBIII

t, read DTCs.

Does the DRBIII

t display Air Bag Lamp Circuit Open?

All

Yes

→ Replace and configure the Instrument Cluster in accordance with

the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Test Complete.

132

INSTRUMENT CLUSTER

 

 

 

 

 

 

 

Content   ..  31  32  33  34   ..