Jeep Wrangler TJ. Manual - part 24

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  22  23  24  25   ..

 

 

Jeep Wrangler TJ. Manual - part 24

 

 

Symptom:

*POOR SOUND QUALITY

POSSIBLE CAUSES

CHECK AUDIO DTCS

CHECK SELECTED RADIO EQ CURVE

SET THE RADIO EQ CURVE

VERIFY SOUND PERFORMANCE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, check for any audio related DTC’s.

Are any Audio related DTCs set?

All

Yes

→ Refer to the Audio category for the related symptom(s).

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 2

2

Turn the ignition on.
With the DRBIII

t, enter body, Instrument Cluster then miscellaneous.

Check the radio EQ curve setting and follow the instructions on the DRBIII

t.

Is the radio EQ curve correct for the audio combination the vehicle is equipped with?

All

Yes

→ Refer to the service information for problems related to poor

sound quality and perform the appropriate checks.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 3

3

Turn the ignition on.
With the DRBIII

t, enter body, Instrument Cluster then miscellaneous.

Set the radio EQ curve. Follow the instructions on the DRBIII

t.

Cycle the ignition switch from off to on.
Check the radio EQ curve setting.
Is the radio EQ curve correct for the audio combination the vehicle is equipped with?

All

Yes

→ Refer to the service information for problems related to poor

sound quality and perform the appropriate checks.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Instrument Cluster in accordance with the Service

Information.
Perform BODY VERIFICATION TEST - VER 1.

93

AUDIO

Symptom:

*CHIME INOPERATIVE AT ALL TIMES

POSSIBLE CAUSES

INSTRUMENT CLUSTER - CHIME INOPERATIVE

TEST

ACTION

APPLICABILITY

1

If there are no possible causes remaining, view repair.

All

Repair

Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.

94

CHIME

Symptom:

*CHIME INOPERATIVE WITH DRIVER SEAT BELT UNFASTENED

POSSIBLE CAUSES

SEAT BELT SWITCH STATUS WRONG

SEAT BELT SWITCH SHORTED

SEAT BELT SWITCH SENSE WIRE SHORT TO GROUND

INSTRUMENT CLUSTER - SEAT BELT SWITCH SHORTED

TEST

ACTION

APPLICABILITY

1

Ensure the drivers seat belt is unfastened.
With the DRB III select: Electro Mech Cluster Input Output.
Turn the ignition on.
Read the Driver Belt SW status.
Does the DRB III show Driver Belt SW: CLOSED?

All

Yes

→ Go To 2

No

→ Replace the Instrument Cluster.

Perform BODY VERIFICATION TEST - VER 1.

2

Disconnect the Seat Belt Switch connector.
With the DRB III select: Electro Mech Cluster Input Outputs.
Turn the ignition on.
Read the Driver Belt Sw status.
Does the DRB III show Seat Belt SW: CLOSED?

All

Yes

→ Go To 3

No

→ Repair Seat Belt switch pigtail wiring for a short to ground or

replace the Seat Belt buckle assembly.
Perform BODY VERIFICATION TEST - VER 1.

3

Turn the ignition off.
Remove the Instrument Cluster from the instrument panel.
Disconnect the Seat Belt Switch connector.
Measure the resistance between ground and the Seat Belt Switch Sense circuit at the
Instrument Cluster C2 connector.
Is the resistance below 100.0 ohms?

All

Yes

→ Repair the Seat Belt Switch Sense wire for a short to ground.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 4

4

If there are no possible causes remaining, view repair.

All

Repair

Replace the Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.

95

CHIME

Symptom:

*CHIME INOPERATIVE WITH EXTERIOR LAMPS ON AND DRIVER
DOOR OPEN

POSSIBLE CAUSES

VERIFY KEY-IN IGNITION, DRIVER’S DOOR OPEN CHIME OPERATION

HEADLAMP SWITCH OUTPUT OPEN

MIC - CHIME INOP WITH EXTERIOR LAMPS ON

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Ensure the key is in the ignition switch all the way.
Open the driver door.
Does the chime sound?

All

Yes

→ Go To 2

No

→ Refer to symptom *CHIME INOPERATIVE WITH KEY IN IG-

NITION, DRIVER’S DOOR OPEN in the CHIME category.
Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Remove the Instrument Cluster From the I/P.
Turn the Exterior Lamps on.
Measure the voltage of the Headlamp Switch Output circuit in the Instrument
Cluster C1 connector.
Is the voltage above 10.0 volts?

All

Yes

→ If there are no possible causes remaining, replace the Instrument

Cluster.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Repair the Headlamp Switch Output circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

96

CHIME

 

 

 

 

 

 

 

Content   ..  22  23  24  25   ..