Jeep Grand Cherokee WK. Manual - part 620

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  618  619  620  621   ..

 

 

Jeep Grand Cherokee WK. Manual - part 620

 

 

B1BBA-PASSENGER SEAT WEIGHT SENSOR SUPPLY CIRCUIT (CONTINUED)

3.

TEST FOR INTERMITTENT CONDITION

With the scan tool, record and erase all DTC’s from the OCM.

If any ACTIVE codes are present they must be resolved before diagnosing any stored codes.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.

Look for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or
contaminated terminals.

The following additional checks may assist you in identifying a possible intermittent problem.

Reconnect any disconnected components and harness connector.

WARNING: To avoid personal injury or death, turn the ignition on, then reconnect the battery.
With the scan tool monitor active codes as you work through the following steps.

WARNING: To avoid personal injury or death, maintain a safe distance from all airbags while performing the
following steps.
Wiggle the wiring harness and connectors of the related airbag circuit or component.

If only stored codes return continue the test until the problem area has been isolated.

In the previous steps you have attempted to recreate the conditions responsible for setting active DTC in question.

Are any ACTIVE DTCs present?

Yes

>> Select the appropriate symptom from Symptom List.

No

>> No problem found at this time. Erase all codes before returning vehicle to customer.

8O - 302

RESTRAINTS - ELECTRICAL DIAGNOSTICS

WK

B1BBB-PASSENGER SEAT WEIGHT SENSOR INPUTS SHORTED TOGETHER

WK

RESTRAINTS - ELECTRICAL DIAGNOSTICS

8O - 303

B1BBB-PASSENGER SEAT WEIGHT SENSOR INPUTS SHORTED TOGETHER (CONTINUED)

For a complete wiring diagram Refer to Section 8W.

When Monitored:
While the CAN bus ignition status is in IGN_RUN.

Set Condition:
If the OCM detects any two sensors voltages below 20mV for 10 minutes while any other sensor is greater
than 40mV. Note: 1 a/d count is equal to 5mV.NOTE: A shorted supply circuit will cause a ’NO RESPONSE
FROM OCM” condition.

Possible Causes

OCS SENSOR CIRCUITS SHORTED TOGETHER

OCCUPANT CLASSIFICATION MODULE (OCM)

Diagnostic Test

1.

VERIFY THAT B1BBA-PASSENGER SEAT WEIGHT SENSOR SUPPLY CIRCUIT DTC IS ACTIVE

With the scan tool, read OCM DTCs.

Does the scan tool display active: B1BBB-PASSENGER SEAT WEIGHT SENSOR INPUTS SHORTED
TOGETHER ?

Yes

>> Replace the OCM in accordance with the Service Information.

Perform the OCS VERIFICATION REQUIRED procedure.

No

>> Go To 2

2.

INSPECT PASSENGER SEAT HARNESS WIRES & CONNECTORS

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Using the wiring diagram/schematic as a guide, inspect the Passenger Seat Harness wiring and connectors. Look
for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or contam-
inated terminals.

Are any of these conditions present?

Yes

>>

NOTE: Do not attempt to repair the Seat Harness. Replace the Seat Harness if the condition inspecting or
testing for is present in the Seat Harness.

Replace the Passenger Seat Harness in accordance with the Service Information.

Perform OCS VERIFICATION TEST - VER 1. (Refer to 8 - ELECTRICAL/RESTRAINTS - DIAGNOSIS
AND TESTING)

No

>> Go To 3

8O - 304

RESTRAINTS - ELECTRICAL DIAGNOSTICS

WK

B1BBB-PASSENGER SEAT WEIGHT SENSOR INPUTS SHORTED TOGETHER (CONTINUED)

3.

TEST FOR INTERMITTENT CONDITION

With the scan tool, record and erase all DTC’s from the OCM.

If any ACTIVE codes are present they must be resolved before diagnosing any stored codes.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.

Look for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or
contaminated terminals.

The following additional checks may assist you in identifying a possible intermittent problem.

Reconnect any disconnected components and harness connector.

WARNING: To avoid personal injury or death, turn the ignition on, then reconnect the battery.
With the scan tool monitor active codes as you work through the following steps.

WARNING: To avoid personal injury or death, maintain a safe distance from all airbags while performing the
following steps.
Wiggle the wiring harness and connectors of the related airbag circuit or component.

If only stored codes return continue the test until the problem area has been isolated.

In the previous steps you have attempted to recreate the conditions responsible for setting active DTC in question.

Are any ACTIVE DTCs present?

Yes

>> Select the appropriate symptom from Symptom List.

No

>> No problem found at this time. Erase all codes before returning vehicle to customer.

WK

RESTRAINTS - ELECTRICAL DIAGNOSTICS

8O - 305

 

 

 

 

 

 

 

Content   ..  618  619  620  621   ..