Jeep Grand Cherokee WK. Manual - part 1322

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1320  1321  1322  1323   ..

 

 

Jeep Grand Cherokee WK. Manual - part 1322

 

 

P0736-GEAR RATIO ERROR IN REVERSE

For the Transmission circuit diagram (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE -
SCHEMATICS AND DIAGRAMS)

For a complete wiring diagram Refer to Section 8W

When Monitored:
Continuously with the ignition on, engine running, with the transmission in gear.

Set Condition:
If the ratio of the Input RPM to the Output RPM does not match the current gear ratio. This DTC can take up
to five minutes of problem identification before illuminating the MIL

Possible Causes

LOW FLUID LEVEL

CUT LR TOWER SEAL ON MAIN VALVE BODY

CUT LR CLUTCH PISTON SEALS

BROKEN OR MISSING LR CLUTCH BLEED ORIFICE (IN LR CLUTCH RETAINER)

CUT LR ACCUMULATOR PISTON SEAL IN MAIN VALVE BODY

CRACKED LR ACCUMULATOR PISTON IN MAIN VALVE BODY

CUT OD/REV PISTON SEALS

BROKEN OR MISSING OD/REV BLEED ORIFICE (IN OD/REV CLUTCH PISTON)

BROKEN REVERSE CARRIER HUB WELD

BROKEN REVERSE SUN GEAR WELD TO THE REACTION CARRIER

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 21 - TRANSMIS-
SION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - DIAGNOSIS AND TESTING).

Theory of Operation

The transmission system uses two speed sensors, one to measure input RPM and one to measure output RPM.
These inputs are essential for proper transmission operation. Therefore, the integrity of this data is verified through
the following checks:

1) Once in a particular gear, if the gear ratio varies from the correct gear ratio, the corresponding in-gear trouble
code is set (DTCs P0731–36).

2) An excessive change in input or output speeds indicating signal intermittent may result in the DTCs P0715 and/or
P0720 being set.

3) If the common speed sensor ground circuit is lost, both sensor inputs will read the pulses from the input speed
sensor when at a stop in neutral. Since the input speed sensor reads 60 teeth from the input clutch hub and the
output speed sensor reads 30 teeth from the park gear, the result is an apparent speed ratio of 1:2 and may cause
the DTC P1794 to set.

Diagnostic Test

1.

DETERMINING IF RELATED DTC’S ARE PRESENT

With the scan tool, check for other transmission DTC’s

Are there any Transmission; solenoid, line pressure, speed sensor, and/or loss of prime DTC’s present?

Yes

>> Refer to appropriate symptom in the Transmission category. Perform the test for P0944–LOSS OF

PRIME first if it is present.

Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST - VER 1.

No

>> Go To 2

21 - 98

AUTOMATIC TRANSMISSION 545RFE - ELECTRICAL DIAGNOSTICS

WK

P0736-GEAR RATIO ERROR IN REVERSE (CONTINUED)

2.

CHECK TO SEE IF DTC IS CURRENT

With the scan tool, perform the Reverse Gear Clutch test. Follow the instructions on the scan tool.

Increase the throttle angle, TPS degree, to 30°, for no more than a few seconds.

CAUTION: Do not overheat the transmission.

NOTE: Make sure to record all EATX DTC EVENT DATA stored in the scan tool for future reference in this
test procedure.

Did the clutch test pass, input speed remain at zero?

Yes

>> Go To 3

No

>> Go To 4

3.

CHECK DTC EVENT DATA

The conditions necessary to set this DTC are not currently present.

With the scan tool, check the DTC EVENT DATA to help identify the conditions in which the DTC was set.

Does the DTC EVENT DATA show an input speed reading of zero?

Yes

>> Go To 8

No

>> Go To 4

4.

POSSIBLE INTERNAL TRANSMISSION CAUSES

Remove the Transmission Oil Pan and Valve Body and check the following per the Service Information:

Clutch or metal debris in the pan

LR clutch tower seal on the main valve body or cuts and the LR accumulator piston and seals.

Air check the Reverse and LR Hydraulic Clutch circuits (in the case) for excessive air leakage.

NOTE: Both Hydraulic Clutch circuits contain a small bleed orifice , a small amount of air leakage is normal.
The Reverse hydraulic clutch circuit bleed orifice connects to the OD hydraulic clutch cavity. A small
amount of air leakage into the OD hydraulic clutch circuit is considered normal.

Were there any problems found?

Yes

>> Repair as necessary. If clutch debris is present, remove the transmission and inspect the Reverse and

LR clutches, and inspect the Transmission Oil Pump and Main Regulator Valve for damage or sticking
in its bore.

Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST - VER 1.

No

>> Go To 5

5.

CLUTCH TEST FAILURE

Did the clutch test fail in reverse?

Yes

>> Go To 6

No

>> Test complete.

WK

AUTOMATIC TRANSMISSION 545RFE - ELECTRICAL DIAGNOSTICS

21 - 99

P0736-GEAR RATIO ERROR IN REVERSE (CONTINUED)

6.

CHECK FOR BROKEN REVERSE SUN GEAR WELD

Working through the windows in the bottom of the case, check for a broken Reverse Sun gear weld to the reaction
carrier as follows:

(1) Hold the Transmission Output Shaft by holding the Transmission Manual Lever in the park position.

(2) Rotate the Input Annulus gear and drive shell, (the drum that encloses the two rearmost carriers).

(3) Check to see if the reaction carrier (the frontmost carrier, whose outer shell is splined to the 2C clutch) is rotat-
ing faster than the drive shell is being turned.

Is the reaction carrier turning faster than the drive shell?

Yes

>> Go To 7

No

>> Replace the reaction carrier per the Service Information.

Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST - VER 1.

7.

CHECK REVERSE CARRIER HUB

Remove the Transmission per the Service Information and inspect the weld on the reverse carrier hub.

Were there any problems found?

Yes

>> Repair as necessary. Refer to the Service Information for proper repair procedures.

No

>> Disassemble and inspect the input clutch assembly. Check the Reverse clutch reaction plate snap ring.

Check the OD and Reverse clutch seals, discs, and bleed orifice (in the OD/Reverse clutch piston).
Check the Reverse hub and shaft. Repair as necessary. Refer to the Service Information for proper
repair procedures.

Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST - VER 1.

8.

CHECK FOR INTERMITTENT OPERATION

Intermittent gear ratio DTCs can be set by problems in the Input and Output Speed Sensor circuits and/or Speed
Sensor Ground circuit.

Remove the Starter Relay

NOTE: Failure to remove the Starter Relay can cause a Transmission - No Response condition.
Check the Speed Sensor wiring and connectors for good connection, then perform a wiggle test using the Trans-
mission Simulator, Miller tool #8333.

Were there any problems found?

Yes

>> Repair as necessary.

Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST - VER 1.

No

>> Test complete.

21 - 100

AUTOMATIC TRANSMISSION 545RFE - ELECTRICAL DIAGNOSTICS

WK

P0740–TCC OUT OF RANGE

For the Transmission circuit diagram (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE -
SCHEMATICS AND DIAGRAMS) .

For a complete wiring diagram Refer to Section 8W

When Monitored:
During Electronically Modulated Converter Clutch (EMCC) Operation.

Set Condition:
Transmission must be in EMCC, with input speed greater than 1750 RPM. TCC-L/R Solenoid achieves the
maximum duty cycle and can not pull engine speed within 60 RPM of input speed. Also when the transmission
is in FEMCC and the engine slips TCC less than 100 RPM for 10 seconds. This DTC can take up to five
minutes of problem identification before illuminating the MIL.

Possible Causes

RELATED DTC P0750 PRESENT

L/R SOLENOID

TORQUE CONVERTER AND/OR INTERNAL TRANSMISSION

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 21 - TRANSMIS-
SION/TRANSAXLE/AUTOMATIC - 45RFE/545RFE - DIAGNOSIS AND TESTING).

Theory of Operation

When in 2nd, 2nd Prime, 3rd, or 4th gear, the torque converter clutch (TCC) can be engaged when certain condi-
tions are met. The TCC piston is electronically modulated by increasing the duty cycle of the LR Solenoid until the
torque converter slip difference (difference between engine and transmission input speed) is within 60 RPM. Then
the LR solenoid is fully energized (FEMCC / 100% duty cycle). Torque converter slip is monitored in FEMCC to
ensure adequate clutch capacity.

Diagnostic Test

1.

DETERMINING IF RELATED DTC P0750 IS PRESENT

With the scan tool, read transmission DTC’s

Is the DTC P0750 present also?

Yes

>> Refer to the Transmission category and perform the appropriate symptom.

Perform 45RFE/545RFE TRANSMISSION VERIFICATION TEST - VER 1.

No

>> Go To 2

WK

AUTOMATIC TRANSMISSION 545RFE - ELECTRICAL DIAGNOSTICS

21 - 101

 

 

 

 

 

 

 

Content   ..  1320  1321  1322  1323   ..