Jeep Grand Cherokee WJ. Manual - part 968

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  966  967  968  969   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 968

 

 

TEST

ACTION

APPLICABILITY

20

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRBIII

t

parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DRBIII

t Freeze Frame information. If possible, try to duplicate the

conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Test Complete.

89

DRIVEABILITY - GAS

P0121-TPS VOLTAGE DOES NOT AGREE WITH MAP —

Continued

Symptom:

P0122-THROTTLE POSITION SENSOR VOLTAGE LOW

When Monitored and Set Condition:

P0122-THROTTLE POSITION SENSOR VOLTAGE LOW

When Monitored:

With the ignition on and battery voltage above 10.4 volts.

Set Condition:

Throttle Position Sensor voltage at the PCM is 0.1 volt for 1.3 seconds.

POSSIBLE CAUSES

THROTTLE POSITION SENSOR SWEEP

INTERMITTENT CONDITION

5 VOLT SUPPLY CIRCUIT SHORTED TO GROUND

5 VOLT SUPPLY CIRCUIT OPEN

THROTTLE POSITION SENSOR INTERNAL FAILURE

THROTTLE POSITION SENSOR SIGNAL CIRCUIT SHORTED TO GROUND

THROTTLE POSITION SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT

TCM INTERNALLY SHORTED THROTTLE POSITION SIGNAL CIRCUIT

PCM 5 VOLT SUPPLY CIRCUIT

PCM THROTTLE POSITION SENSOR SIGNAL

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, read the Throttle Position Sensor voltage.

Is the voltage below 0.2 volts?

All

Yes

Go To

2

No

Go To

11

2

Turn the ignition off.
Disconnect the Throttle Position Sensor harness connector.
Turn the ignition on.
Measure the voltage of the 5 Volt Supply circuit in the TPS harness connector.
Is the voltage between 4.5 to 5.5 volts?

All

Yes

Go To

3

No

Go To

8

90

DRIVEABILITY - GAS

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Throttle Position Sensor harness connector.
With the DRBIII

t, monitor the Throttle Position Sensor voltage.

Turn the ignition on.
Is the voltage above 4.5 volts?

All

Yes

Replace the Throttle Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Go To

4

4

Turn the ignition off.
Disconnect the Throttle Position Sensor harness connector.
Measure the resistance of the Throttle Position Sensor Signal circuit in the Throttle
Position Sensor harness connector to ground.
Is the resistance below 100 ohms?

All

Yes

Repair the Throttle Position Sensor Signal circuit for a short to
ground.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Go To

5

5

Turn the ignition off.
Disconnect the Throttle Position Sensor harness connector.
Measure the resistance between the Throttle Position Sensor Signal circuit and the
Sensor ground circuit in the Throttle Position Sensor harness connector.
Is the resistance below 100 ohms?

All

Yes

Repair the Throttle Position Sensor Signal circuit for a short to
the Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Go To

6

6

Turn the ignition off.
Disconnect the Throttle Position Sensor harness connector.
Disconnect the TCM harness connector.
With the DRBIII

t, monitor the Throttle Position Sensor voltage.

Turn the ignition on.
Is the voltage above 4.5 volts?

All

Yes

Replace the Transmission Control Module.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Go To

7

7

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

91

DRIVEABILITY - GAS

P0122-THROTTLE POSITION SENSOR VOLTAGE LOW —

Continued

TEST

ACTION

APPLICABILITY

8

Turn the ignition off.
Disconnect the Throttle Position Sensor harness connector.
Measure the resistance of the 5 Volt Supply circuit in the Throttle Position Sensor
harness connector to ground.
Is the resistance below 100 ohms?

All

Yes

Repair the 5 Volt Supply circuit for a short to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Go To

9

9

Turn the ignition off.
Disconnect the Throttle Position Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance of the 5 Volt Supply circuit between the Throttle Position
Sensor harness connector and the PCM harness connector.
Is the resistance below 5 ohms?

All

Yes

Go To

10

No

Repair the 5 Volt Supply circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

10

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

11

Turn the ignition on.
With the DRBIII

t, monitor the Throttle Position Sensor voltage.

Slowly open the throttle from the idle position to the wide open throttle position.
Does voltage start at approximately 0.8 volts and go above 3.5 volts with a smooth
voltage change?

All

Yes

Go To

12

No

Replace the Throttle Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

12

WARNING: KEEP CLEAR OF THE ENGINE’S MOVING PARTS.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRBIII

t

parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DRBIII

t Freeze Frame information. If possible, try to duplicate the

conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Test Complete.

92

DRIVEABILITY - GAS

P0122-THROTTLE POSITION SENSOR VOLTAGE LOW —

Continued

 

 

 

 

 

 

 

Content   ..  966  967  968  969   ..