Jeep Grand Cherokee WJ. Manual - part 629

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  627  628  629  630   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 629

 

 

Symptom:

P0235-TURBOCHARGER

BOOST

SENSOR

SUPPLY

LOW

EX-

CEEDED

When Monitored and Set Condition:

P0235-TURBOCHARGER BOOST SENSOR SUPPLY LOW EXCEEDED

When Monitored:

With the ignition on.

Set Condition:

The turbocharger boost pressure sensor supply voltage stays below 4.75

volts for at least 2 seconds.

POSSIBLE CAUSES

INTERMITTENT CONDITION

TURBOCHARGER BOOST PRESSURE/INTAKE AIR TEMPERATURE SENSOR

5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND

5-VOLT SUPPLY AND SENSOR GROUND CIRCUITS SHORTED TOGETHER

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, erase ECM DTCs.
Turn the ignition off, wait 30 seconds, then turn the ignition on.
With the DRB, read ECM DTCs.
Did this DTC reset?

All

Yes

Go To

2

No

Go To

6

2

Turn the ignition off.
Disconnect the Turbocharger Boost Pressure/IAT Sensor harness connector.
Turn the ignition on.
Measure the voltage between ground and the Turbocharger Boost Pressure Sensor
5-volt Supply circuit.
Is the voltage above 4.7 volts?

All

Yes

Replace the Turbocharger Boost Pressure/Intake Air Tempera-
ture Sensor.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

3

3

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Turbocharger Boost Pressure/IAT Sensor harness connector.
Measure the resistance between ground and the 5-volt Supply circuit.
Is the resistance above 100 kohms?

All

Yes

Go To

4

No

Repair the 5-volt Supply circuit for a short to ground.
Perform ROAD TEST VERIFICATION - VER-2.

72

DRIVEABILITY - DIESEL

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Turbocharger Boost Pressure/IAT Sensor harness connector.
Measure the resistance between the 5-volt Supply circuit and the Sensor Ground
circuit.
Is the resistance above 100 kohms?

All

Yes

Go To

5

No

Repair the 5-volt Supply and Sensor Ground circuits for a short
together.
Perform ROAD TEST VERIFICATION - VER-2.

5

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

6

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform ROAD TEST VERIFICATION - VER-2.

No

Test Complete.

73

DRIVEABILITY - DIESEL

P0235-TURBOCHARGER BOOST SENSOR SUPPLY LOW EXCEEDED —

Continued

Symptom:

P0400-EGR OPEN CIRCUIT

When Monitored and Set Condition:

P0400-EGR OPEN CIRCUIT

When Monitored:

With the ignition on.

Set Condition:

The ECM detects an open or short to ground on the electric vacuum

modulator control circuit.

POSSIBLE CAUSES

INTERMITTENT CONDITION

FUSED ASD RELAY OUTPUT CIRCUIT OPEN

EGR SOLENOID CONTROL CIRCUIT SHORTED TO GROUND

EGR SOLENOID CONTROL CIRCUIT OPEN

SUBSTITUTE EGR SOLENOID

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, erase ECM DTCs.
Perform several ignition cycles, turning the ignition off for at least 10 seconds
between each ignition cycle.
Monitor the DRB for ECM DTCs.
Did this DTC reset?

All

Yes

Go To

2

No

Go To

7

2

Turn the ignition off.
Disconnect the EGR Solenoid harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the Fused ASD Relay Output
circuit.
Does the test light illuminate brightly?

All

Yes

Go To

3

No

Repair the Fused ASD Relay Output circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

74

DRIVEABILITY - DIESEL

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the EGR Solenoid harness connector.
Disconnect the ECM harness connectors.
Measure the resistance between ground and the EGR Solenoid Control circuit.
Is the resistance above 100 kohms?

All

Yes

Go To

4

No

Repair the EGR Solenoid Control circuit for a short to ground.
Perform ROAD TEST VERIFICATION - VER-2.

4

Turn the ignition off.
Disconnect the EGR Solenoid harness connector.
Disconnect the ECM harness connectors.
Measure the resistance of the EGR Solenoid Control circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

5

No

Repair the EGR Solenoid Control circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

5

Turn the ignition off.
Install a substitute EGR Solenoid in place of the vehicle’s EGR Solenoid.
NOTE: Ensure the ECM and EGR Solenoid harness connectors are con-
nected.
Turn the ignition on.
With the DRB, check for this DTC to reset.
Did this DTC reset?

All

Yes

Go To

6

No

Replace the EGR Solenoid.
Perform ROAD TEST VERIFICATION - VER-2.

6

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

75

DRIVEABILITY - DIESEL

P0400-EGR OPEN CIRCUIT —

Continued

 

 

 

 

 

 

 

Content   ..  627  628  629  630   ..