Jeep Grand Cherokee WJ. Manual - part 620

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  618  619  620  621   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 620

 

 

TEST

ACTION

APPLICABILITY

5

Turn the ignition off.
Disconnect the PCM C3 harness connector.
Measure the resistance of the SCI Transmit circuit between the PCM C3 connector
and the DLC.
Is the resistance below 5.0 ohms?

All

Yes

Go To

6

No

Repair the SCI Transmit circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

6

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

36

COMMUNICATION

*NO RESPONSE FROM PCM (SCI ONLY) - DIESEL ONLY —

Continued

Symptom:

*PCI BUS COMMUNICATION FAILURE

POSSIBLE CAUSES

WITH THE DRB PERFORM A MODULE SCAN

OPEN PCI BUS CIRCUIT AT THE DATA LINK CONNECTOR

USING THE DRB, PERFORM THE PCI BUS CONTROL MODE

DISCONNECT THE MODULE(S) HARNESS CONNECTOR

PCI BUS CIRCUIT SHORTED TO VOLTAGE

DISCONNECT THE MODULE(S) HARNESS CONNECTOR

PCI BUS CIRCUIT SHORTED TO GROUND

WIRING HARNESS INTERMITTENT DEFECT

TEST

ACTION

APPLICABILITY

1

Note: Determine which modules this vehicle is equipped with before begin-
ning.
Connect the Diagnostic Junction Port Tester #8339 to the DRB and to the Diagnostic
Junction Port.
Using the DRB, along with the Diagnostic Junction Port Tester #8339, select
Junction Port Tool then PCI Bus Module Scan and follow the instructions on the
DRB.
Was the DRB able to scan (I/D or communicate) with any modules?

All

Yes

Refer to the Communication category for the related symptom(s).
(Individual module no responses).
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Turn the ignition off.
Measure the resistance of the PCI Bus circuit between the Data Link Connector and
the Diagnostic Junction Port connector.
Is the resistance below 5.0 ohms?

All

Yes

Go To

3

No

Repair the PCI Bus circuit for an open between the DLC and the
Diagnostic Junction Port.
Perform BODY VERIFICATION TEST - VER 1.

37

COMMUNICATION

TEST

ACTION

APPLICABILITY

3

Note: Determine which modules this vehicle is equipped with before begin-
ning.
Connect the Diagnostic Junction Port Tester #8339 to the DRB and to the Diagnostic
Junction Port.
Using the DRB, along with the Diagnostic Junction Port Tester #8339, select
Junction Port Tool then PCI Bus Control Mode and follow the instructions on the
DRB.
Note: Perform this function on each pin that is equipped with a PCI Bus
circuit.
Did the DRB display No Modules Responding from any of the pins that were
scanned?

All

Yes

Go To

4

No

Check the PCI Bus circuit between the DLC and the Diagnostic
Junction Port connector for a short to voltage or to ground.
Perform BODY VERIFICATION TEST - VER 1.

4

Disconnect the Diagnostic Junction Port Tester cable from the DRB. Keep the tester
connected to the Diagnostic Junction Port.
Turn the ignition on.
Measure the voltage of the PCI Bus circuit on the Diagnostic Junction Port Tester
that the DRB displayed No Modules Responding.
Is the voltage steadily above 7.0 volts?

All

Yes

Go To

5

No

Go To

6

5

Measure the voltage of the PCI Bus circuit on the Diagnostic Junction Port tester
that previously measured above 7.0 volts.
Note: Turn the ignition off before disconnecting any module harness
connector then turn the ignition on.
Disconnect the module harness connector(s). Note: If the problem occurred on pins 1
or 2 of the Diagnostic Junction Port tester, observe the voltmeter while disconnecting
each module connector one at a time.
Is the voltage steadily above 7.0 volts with the module(s) disconnected.

All

Yes

Repair the PCI Bus circuit that measured over 7.0 volts for a
short to voltage.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the module that when disconnected the short to voltage
was eliminated.
Perform BODY VERIFICATION TEST - VER 1.

6

Disconnect the Diagnostic Junction Port Tester cable from the DRB. Keep the tester
connected to the Diagnostic Junction Port.
Turn the ignition off.
Disconnect the negative battery cable.
Measure the resistance between ground and the PCI Bus circuit on the Diagnostic
Junction Port Tester that the DRB displayed No Modules Responding.
Is the resistance below 100.0 ohms?

All

Yes

Go To

7

No

Go To

8

38

COMMUNICATION

*PCI BUS COMMUNICATION FAILURE —

Continued

TEST

ACTION

APPLICABILITY

7

Disconnect the negative battery cable.
Measure the resistance between ground and the PCI Bus circuit at the Diagnostic
Junction Port tester that previously measured below 100.0 ohms.
Disconnect the module harness connector(s). Note: If the problem occurred on pins 1
or 2 of the Diagnostic Junction Port tester, observe the ohmmeter while disconnecting
each module connector one at a time.
Is the resistance below 100.0 ohms with the module(s) disconnected.

All

Yes

Repair the PCI Bus circuit that measured below 100.0 ohms for a
short to ground.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the module that when disconnected the short to ground
was eliminated.
Perform BODY VERIFICATION TEST - VER 1.

8

Turn the ignition off.
Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
Note: Visually inspect the related wire harness connectors. Look for broken,
bent, pushed out, or corroded terminals.
Were any problems found?

All

Yes

Repair wiring harness/connectors as necessary.
Perform BODY VERIFICATION TEST - VER 1.

No

Test Complete.

39

COMMUNICATION

*PCI BUS COMMUNICATION FAILURE —

Continued

 

 

 

 

 

 

 

Content   ..  618  619  620  621   ..