Jeep Grand Cherokee WJ. Manual - part 1256

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1254  1255  1256  1257   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1256

 

 

Symptom:

*DRIVERS DOOR KEY FAILS TO DISARM VTSS

POSSIBLE CAUSES

DRIVER DOOR MODULE RESET

RESET DOOR MODULE

OPEN GROUND CIRCUIT

DRIVER CYLINDER LOCK SWITCH SENSE CIRCUIT SHORTED TO GROUND

OPEN DRIVER CYLINDER LOCK SWITCH SENSE CIRCUIT

DRIVER CYLINDER LOCK SWITCH

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t in VTSS, Sensor Display, read the Driver Key Cylinder Sw voltage.

Rotate the Key in the Door Key Cylinder from the normal position to the unlock
position.
Does the Driver Key Cylinder Sw voltage change from 5.0 to 1.6 volts?

All

Yes

Go To

2

No

Go To

3

2

Reset the DDM by removing and reinstalling the JB POWER Fuse #12 in the Power
Distribution Center.
Attempt to disarm the VTSS using the Door Key.
Can the VTSS now be disarmed using the Door Key?

All

Yes

Resetting the Driver Door Module has corrected the problem.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.

3

Disconnect the Driver Cylinder Lock Switch harness connector.
Using a 12-volt Test Light connected to 12-volts, check the Driver Cylinder Lock
Switch Ground circuit.
Does the test light illuminate?

All

Yes

Go To

4

No

Repair the Driver Cylinder Lock Switch Ground circuit for an
open.
Perform VTSS VERIFICATION TEST - 1A.

4

Disconnect the Driver Door Module C1 harness connector.
Disconnect the Driver Cylinder Lock Switch harness connector.
Using a 12-volt Test Light connected to 12-volts, check the Driver Cylinder Lock
Switch Sense circuit.
Does the test light illuminate?

All

Yes

Repair the Driver Door Cylinder Lock Switch Sense circuit for a
short to ground.
Perform VTSS VERIFICATION TEST - 1A.

No

Go To

5

527

VEHICLE THEFT/SECURITY

TEST

ACTION

APPLICABILITY

5

Disconnect the Driver Door Module C1 harness connector.
Disconnect the Driver Cylinder Lock Switch harness connector.
Measure the resistance of the Sense circuit.
Is the resistance below 5.0 ohms?

All

Yes

Replace the Driver Cylinder Lock Switch in accordance with the
Service Information.
Perform VTSS VERIFICATION TEST - 1A.

No

Repair the Driver Cylinder Lock Switch Sense circuit for an open.
Perform VTSS VERIFICATION TEST - 1A.

528

VEHICLE THEFT/SECURITY

*DRIVERS DOOR KEY FAILS TO DISARM VTSS —

Continued

Symptom:

*HAZARD LAMPS FAIL TO FLASH WITH ALARM TRIPPED

POSSIBLE CAUSES

VERIFY HAZARD OPERATION

BCM -- HAZARDS INOPERATIVE WITH VTSS ALARM TRIPPED

JUNCTION BLOCK

TEST

ACTION

APPLICABILITY

1

Turn the Hazard Lamps on.
Do the Hazard Lamps operate properly?

All

Yes

Go To

2

No

Check and diagnose related Body Control Module Diagnostic
Trouble Codes. If no DTCs are present, refer to the Service
Information.
Perform VTSS VERIFICATION TEST - 1A.

2

Remove the BCM from the Junction Block.
Connect a jumper wire between cavity 10 of the Junction Block and ground.
Do the hazard lamps operate?

All

Yes

Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.

No

Replace the Junction Block in accordance with the Service Infor-
mation.
Perform VTSS VERIFICATION TEST - 1A.

529

VEHICLE THEFT/SECURITY

Symptom:

*HEADLAMPS FAIL TO FLASH WITH ALARM TRIPPED (IF EN-
ABLED)

POSSIBLE CAUSES

VERIFY LOW BEAM OPERATION

BCM -- HEADLAMPS FAIL TO FLASH WHEN VTSS IS IN ALARM

TEST

ACTION

APPLICABILITY

1

Turn the Low Beam Headlamps on.
Do the Low Beam Headlamps operate properly?

All

Yes

Replace the Body Control Module.
Perform VTSS VERIFICATION TEST - 1A.

No

Refer to the Exterior Lighting symptom list and also check for
related Body Control Module Diagnostic Trouble Codes.
Perform VTSS VERIFICATION TEST - 1A.

530

VEHICLE THEFT/SECURITY

 

 

 

 

 

 

 

Content   ..  1254  1255  1256  1257   ..