Jeep Grand Cherokee WJ. Manual - part 1184

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1182  1183  1184  1185   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1184

 

 

Symptom:

HEADLAMP SW SHORT TO GROUND

When Monitored and Set Condition:

HEADLAMP SW SHORT TO GROUND

When Monitored:

Ignition in RUN and IOD fuse/connector installed.

Set Condition:

This DTC sets if the BCM detects voltage on the MUX circuit below 0.3

volts.

POSSIBLE CAUSES

HEADLAMP SWITCH MUX SHORTED

LEFT MULTI-FUNTION SWITCH SHORTED

BCM

TEST

ACTION

APPLICABILITY

1

Disconnect the left multi-function switch connector.
Turn ignition on.
Does the DRB display

9Headlamp switch9 5.0 volts?

All

No

Go To

2

Yes

Replace the left multi-function switch.
Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Disconnect the left multi-function switch connector.
Disconnect the Body Control Module C-1 connector.
Measure the resistance of the headlamp switch mux circuit to ground at the left
multi-function switch connector.
Is the resistance below 5.0 ohms?

All

Yes

Repair the Headlamp Switch Mux circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

3

3

If there are no possible causes remaining, view repair.

All

Repair

Replace the Body Control Module
Perform BODY VERIFICATION TEST - VER 1.

239

EXTERIOR LIGHTING

Symptom:

HIGH BEAM RELAY CKT SHORTED HI

When Monitored and Set Condition:

HIGH BEAM RELAY CKT SHORTED HI

When Monitored:

Ignition in RUN and IOD fuse/connector installed.

Set Condition:

This condition is set when the BCM is trying to activate the High beam

relay and excessive current is sinked into the BCM.

POSSIBLE CAUSES

HI BEAM RELAY

HIGH BEAM RELAY CONTROL CIRCUIT SHORTED TO B(+)

BCM HIGH BEAM CONTROL SHORT TO BATTERY

TEST

ACTION

APPLICABILITY

1

Install a known good relay in place of the High Beam relay.
Does the system now operate correctly?

All

Yes

Replace the High Beam relay.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Remove the High Beam relay from the Junction Block.
Turn ignition off. Remove the Body Control Module from the Junction Block.
Turn ignition on.
Using a voltmeter measure the High Beam Relay control ckt cavity 86 to ground at
the Junction Block.
Was the voltage greater than 1.0 volt?

All

Yes

Replace the Junction Block.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

240

EXTERIOR LIGHTING

Symptom:

LOW BEAM RELAY CKT SHORTED HI

When Monitored and Set Condition:

LOW BEAM RELAY CKT SHORTED HI

When Monitored:

Ignition in RUN and IOD fuse/connector installed.

Set Condition:

This condition is set when the BCM is trying to activate the lo beam relay

and excessive current is sinked into the BCM.

POSSIBLE CAUSES

LOW BEAM RELAY

LOW BEAM RELAY CONTROL SHORTED TO B(+)

BCM LOW BEAM CONTROL SHORT TO BATTERY

TEST

ACTION

APPLICABILITY

1

Install a known good relay in place of the Low Beam relay.
Does the system now operate correctly?

All

Yes

Replace the Low Beam relay.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Remove the Low Beam relay from the Junction Block.
Turn ignition off. Remove the Body Control Module from the Junction Block.
Turn ignition on.
Using a voltmeter measure the Low Beam Relay control ckt cavity 86 to ground at the
Junction Block.
Was the voltage greater than 1.0 volt?

All

Yes

Replace the Junction Block.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

241

EXTERIOR LIGHTING

Symptom:

LOW BEAM RELAY CKT SHORTED LO/OPEN

When Monitored and Set Condition:

LOW BEAM RELAY CKT SHORTED LO/OPEN

When Monitored:

Ignition in RUN and IOD fuse/connector installed.

Set Condition:

This condition detects if the lo beam relay has not been installed in the

vehicle by monitoring the BCM lo beam relay output for battery voltage applied.

POSSIBLE CAUSES

LOW BEAM RELAY MISSING

LOW BEAM RELAY

OPEN FUSED B(+)

LOW BEAM RELAY CTL CKT OPEN

LOW BEAM RELAY CTL CKT SHORTED TO GROUND

BCM LOW BEAM CTL CKT SHT LO/OP

TEST

ACTION

APPLICABILITY

1

Looking at the Junction Block, see if the relay is present.
Is the relay present?

All

Yes

Go To

2

No

Install the correct relay.
Perform BODY VERIFICATION TEST - VER 1.

2

Install a known good relay in place of the Low Beam relay.
Does the system now operate correctly?

All

Yes

Replace the Low Beam relay.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

3

3

For the results of this test to be valid, voltage must be present at the Junction Block
C5 connector cavity #1.
Measure the voltage of the fused B(+) circuits to Low Beam relay cavities #30 and
#85.
Is the voltage above 10.0 volts at both cavities?

All

Yes

Go To

4

No

Replace the Junction Block.
Perform BODY VERIFICATION TEST - VER 1.

242

EXTERIOR LIGHTING

 

 

 

 

 

 

 

Content   ..  1182  1183  1184  1185   ..