Jeep Grand Cherokee WJ. Manual - part 1169

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1167  1168  1169  1170   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1169

 

 

TEST

ACTION

APPLICABILITY

7

Disconnect the negative battery cable.
Measure the resistance between ground and the PCI Bus circuit at the Diagnostic
Junction Port tester that previously measured below 100.0 ohms.
Disconnect the module harness connector(s). Note: If the problem occurred on pins 1
or 2 of the Diagnostic Junction Port tester, observe the ohmmeter while disconnecting
each module connector one at a time.
Is the resistance below 100.0 ohms with the module(s) disconnected.

All

Yes

Repair the PCI Bus circuit that measured below 100.0 ohms for a
short to ground.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the module that when disconnected the short to ground
was eliminated.
Perform BODY VERIFICATION TEST - VER 1.

8

Turn the ignition off.
Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
Note: Visually inspect the related wire harness connectors. Look for broken,
bent, pushed out, or corroded terminals.
Were any problems found?

All

Yes

Repair wiring harness/connectors as necessary.
Perform BODY VERIFICATION TEST - VER 1.

No

Test Complete.

179

COMMUNICATION

*PCI BUS COMMUNICATION FAILURE —

Continued

Symptom:

*UNABLE TO ACCESS DRIVER DOOR MODULE AND/OR PASSEN-
GER DOOR MODULE WITH DRBIII

t

POSSIBLE CAUSES

ATTEMPT TO COMMUNICATE WITH THE BCM

CHECK BCM DTCS

INSPECT JUNCTION BLOCK FUSE #22 AND #28

CHECK VOLTAGE SUPPLY TO BCM - JUNCTION BLOCK BCM CONNECTOR CAVITY 5

CHECK VOLTAGE SUPPLY TO BCM - JUNCTION BLOCK BCM CONNECTOR CAVITY 25

BODY CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, enter Body then Body Computer.
Was the DRB able to I/D or communicate with the BCM?

All

Yes

Go To

2

No

Refer to the symptom list for problems related to no communica-
tion with the BCM.
Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition on.
With the DRB, enter Body then Body Computer and read DTC’s.
Are any DTCs present?

All

Yes

Refer to the appropriate category and perform the diagnostic test
associated with the DTC that is set.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

3

3

Turn the ignition off.
Remove and inspect fuse #22 and #28 from the junction block.
Is either fuse open?

All

Yes

Refer to the wiring diagrams in the service information to help
isolate a possible short to ground condition, replace fuse and
retest.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

4

4

Turn the ignition off.
Note: Ensure Fuse #22 is installed in the junction block.
Remove the BCM from the Junction Block.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused Ignition Switch
Output circuit at the Junction Block Body Control Module connector cavity 5.
Is the test light illuminated?

All

Yes

Go To

5

No

Replace the Junction Block.
Perform BODY VERIFICATION TEST - VER 1.

180

COMMUNICATION

TEST

ACTION

APPLICABILITY

5

Turn the ignition off.
NOTE: Ensure Fuse #28 is installed in the junction block.
Remove the BCM from the Junction Block.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused Ignition Switch
Output circuit at the Junction Block Body Control Module connector cavity 25.
Is the test light illuminated?

All

Yes

Go To

6

No

Replace the Junction Block.
Perform BODY VERIFICATION TEST - VER 1.

6

If there are no possible causes remaining, view repair.

All

Repair

Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.

181

COMMUNICATION

*UNABLE TO ACCESS DRIVER DOOR MODULE AND/OR PASSENGER
DOOR MODULE WITH DRBIII

Continued

Symptom:

* DRIVER DOOR AJAR CIRCUIT SHORTED TO GROUND

POSSIBLE CAUSES

DRIVER DOOR LOCK MOTOR/AJAR SWITCH SHORTED TO GROUND

DRIVER DOOR AJAR SWITCH SENSE CKT SHORTED TO GROUND

DRIVER DOOR MODULE

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t in Inputs/Outputs, read the DR DOOR AJAR SW state.

Disconnect the Driver Door Lock Motor/Ajar Switch harness connector.
With the DRBIII

t in Inputs/Outputs, read the DR DOOR AJAR SW state.

Does the Switch State change from CLOSED to OPEN?

All

Yes

Replace the Driver Door Lock Motor/Ajar Switch in accordance
with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

2

2

Disconnect the DDM harness connector.
Disconnect the Driver Door Lock Motor/Ajar Switch harness connector.
Using a 12-volt Test Light connected to 12-volts, check the Sense circuit.
Does the Test Light illuminate?

All

Yes

Repair the Driver Door Ajar Switch Sense circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.

182

DOOR AJAR

 

 

 

 

 

 

 

Content   ..  1167  1168  1169  1170   ..