Jeep Grand Cherokee WJ. Manual - part 1110

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1108  1109  1110  1111   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1110

 

 

Symptom:

P1793-TRD LINK COMMUNICATION ERROR

When Monitored and Set Condition:

P1793-TRD LINK COMMUNICATION ERROR

When Monitored:

During torque managed shifts with Throttle angle above 54 degrees.

This system is also tested whenever the vehicle is stopped and the engine speed is below
1000 RPM.

Set Condition:

This code is set when the Transmission Control Module sends two

subsequent Torque Reduction messages (pulses the TRD ckt to ground) to the Powertrain
Control Module via the TRD link circuit and the TCM does not receive a confirmation from
the PCM over the communication bus.

POSSIBLE CAUSES

RELATED DTC’S PRESENT

INTERMITTENT WIRING & CONNECTORS

TORQUE MANAGEMENT REQUEST SENSE CIRCUIT OPEN

TORQUE MANAGEMENT REQUEST SENSE SHORT TO GROUND

TORQUE MANAGEMENT REQUEST SENSE CIRCUIT SHORTED TO VOLTAGE

PCM - TRD LINK COMMUNICATION ERROR

TCM - TRD LINK COMMUNICATION ERROR

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0705 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

45RFE AUTO

TRANS

Continue

Go To

2

199

TRANSMISSION

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, check for other transmission DTC’s

Are any of the following codes present also? P1716, P0731, P0732, P0733, P0734,
P1736.

45RFE AUTO

TRANS

Yes

If any of these codes are present, disregard the P1793 DTC. Refer
to the symptom list and perform the diagnostics for the other
DTC’s first.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

3

3

With the DRBIII

t, Check the STARTS SINCE SET counter.

Note: This counter only applies to the last code set.
Is the STARTS SINCE SET equal to zero?

45RFE AUTO

TRANS

Yes

Go To

4

No

Go To

9

4

Turn the ignition switch to the lock position.
Disconnect the TCM harness connector.
Disconnect the PCM harness connector(s).
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Torque Management Request Sense circuit from the
TCM connector to the PCM connector.
Is the resistance above 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair the open Torque Management Request Sense circuit.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

5

5

Turn the ignition switch to the lock position.
Disconnect the TCM harness connector.
Disconnect the PCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the Torque Management Request Sense circuit and
ground.
Is the resistance below 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair Torque Management Request Sense circuit short to
ground.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

6

200

TRANSMISSION

P1793-TRD LINK COMMUNICATION ERROR —

Continued

TEST

ACTION

APPLICABILITY

6

Turn the ignition switch to the lock posiiton.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage of the Torque Management Request Sense circuit in the TCM
connector.
Is the voltage above 10.5 volts?

45RFE AUTO

TRANS

Yes

Repair Torque Management Request Sense circuit short to volt-
age.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

7

7

Turn the ignition switch to the lock position.
Disconnect the TCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage of the Torque Management Request Sense circuit in the TCM
connector.
Is the voltage above 7.0 volts?

45RFE AUTO

TRANS

Yes

Replace the TCM. WITH THE DRBIII

t PERFORM QUICK

LEARN.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

8

8

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace the Powertrain Control Module
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

9

The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wires while checking for shorts and open circuits.
Were any problems found?

45RFE AUTO

TRANS

Yes

Repair as necessary.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Test Complete.

201

TRANSMISSION

P1793-TRD LINK COMMUNICATION ERROR —

Continued

Symptom:

P1794-SPEED SENSOR GROUND ERROR

When Monitored and Set Condition:

P1794-SPEED SENSOR GROUND ERROR

When Monitored:

The Tdn gear ratio is monitored continuously while the Transmission

is in gear.

Set Condition:

After a TCM reset in neutral and Nt/No equals a ratio of input to output

of 2 to 1.

POSSIBLE CAUSES

INTERMITTENT WIRING & CONNECTORS

INPUT SPEED SENSOR GROUND CIRCUIT OPEN

OUTPUT SPEED SENSOR GROUND CIRCUIT OPEN

INPUT SPEED SENSOR GROUND CIRCUIT SHORT TO GROUND

OUTPUT SPEED SENSOR GROUND CIRCUIT SHORT TO GROUND

INPUT SPEED SENSOR GROUND CIRCUIT SHORT TO VOLTAGE

OUTPUT SPEED SENSOR GROUND CIRCUIT SHORT TO VOLTAGE

TCM - SPEED SENSOR GROUND CIRCUIT

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0705 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

45RFE AUTO

TRANS

Continue

Go To

2

202

TRANSMISSION

 

 

 

 

 

 

 

Content   ..  1108  1109  1110  1111   ..