Jeep Grand Cherokee WJ. Manual - part 1107

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1105  1106  1107  1108   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1107

 

 

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing transmission symptom diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0705 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to Symptom diagnosis.

45RFE AUTO

TRANS

Continue

Go To

2

2

With the DRBIII

t, check for other Transmission DTC’s

Are there any Line Pressure related DTC’s P1720, P1721, P1722, P1724, or P1791
present?

45RFE AUTO

TRANS

Yes

Refer to symptom list and perform appropriate symptoms for Loss
of Prime or Line Pressure DTC’s.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

3

3

With the DRBIII

t, check for other Transmission DTC’s

Are there any other DTC’s P0733 3rd Ratio and/or P1781 OD Pressure Switch
present?

45RFE AUTO

TRANS

Yes

Replace the Transmission Solenoid/TRS assembly in accordance
with the Service Information.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

4

4

Start engine.
Warm transmission to 180 degrees.
Firmly apply brakes.
With the DRBIII

t, monitor the Transmission Line Pressure.

Move the shift lever to each gear position and record the line pressure reading. Allow
the pressure to stabilize for at least 5 seconds in each range.
Did the line pressure remain at a steady value between 85 and 95 PSI during the
procedure?

45RFE AUTO

TRANS

Yes

Go To

5

No

Go To

11

187

TRANSMISSION

P1787-OD HYDRAULIC PRESSURE TEST FAILURE —

Continued

TEST

ACTION

APPLICABILITY

5

Ignition on, engine not running.
While observing Actual Line Pressure with the DRBIII

t, firmly push the line

pressure sensor connector towards the Transmission.
Did the Actual Line Pressure change to about 30 PSI when the sensor connector was
pushed?

45RFE AUTO

TRANS

Yes

Disconnect and properly reconnect the Line Pressure Sensor
harness connector. Inspect terminals and repair as necessary.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

6

6

Turn the ignition off to the lock position.
Remove the Starter Relay.
NOTE: Failure to remove Starter Relay can cause a TCM - No Response
condition.
Install Transmission Simulator Miller tool #8333.
Ignition on, engine not running.
With the DRBIII

t, monitor the Line Pressure during the following step.

Using the Transmission Simulator, set the rotary knob to each of the 3 line pressure
positions.
Note: All three DRBIII

t line pressure sensor voltage readings should be within 0.25

volts of the voltage reading specified on simulator.
Did the Line Pressure remain steady while changing the knob position.

45RFE AUTO

TRANS

Yes

Go To

7

No

Go To

10

7

Turn the ignition off to the lock position.
Disconnect the Transmission Control Module harness connector.
Disconnect the Line Pressure Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the 5-volt Supply circuit from the Line Pressure Sensor
harness connector to the Transmission Control Module harness connector.
Is the resistance above 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair the 5-volt supply circuit for an open.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

8

8

Turn the ignition off to the lock position.
Disconnect the Transmission Control Module harness connector.
Disconnect the Line Pressure Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the 5-volt Supply circuit and ground.
Is the resistance Below 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair the 5-volt Supply circuit for a short to ground.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

9

188

TRANSMISSION

P1787-OD HYDRAULIC PRESSURE TEST FAILURE —

Continued

TEST

ACTION

APPLICABILITY

9

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIII

t PERFORM QUICK LEARN.

Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

10

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

Replace the Line Pressure Sensor.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

11

Perform a visual inspection of all connectors, wiring, and cooler connections before
proceeding. Repair as necessary.
Check the Transmission fluid level per Service Information. Adjust if necessary.
With the DRBIII

t, Check the STARTS SINCE SET counter.

NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter 2 or less?

45RFE AUTO

TRANS

Yes

Go To

12

No

Go To

21

12

Turn the ignition off to the lock position.
Remove the Starter Relay.
NOTE: Failure to remove the Starter Relay can cause a TCM - No Response
condition.
Install Transmission Simulator Miller tool #8333.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the DRBIII

t, monitor the OD Pressure Switch state.

With the Transmission Simulator Miller tool# 8333, place the selector switch on OD.
While pressing the Pressure Switch test button, wiggle the wiring harness and
connectors pertaining to the OD Pressure Switch.
Did the OD pressure switch state change to closed and remain closed while wiggling
the wires?

45RFE AUTO

TRANS

Yes

Go To

13

No

Go To

16

189

TRANSMISSION

P1787-OD HYDRAULIC PRESSURE TEST FAILURE —

Continued

TEST

ACTION

APPLICABILITY

13

The Transmission must be at operating temperature prior to checking fluid level.
Adjusting fluid level on a cold Transmission will result in an overfilled Transmission.
Check the Transmission Fluid Level per the Service Information.
NOTE: The Transmission must be hot when checking oil level. When the
temperature is below 10 degrees C - 50 degrees F. it is possible that no oil
will show on the dipstick, even though the Transmission has an adequate
fill level when warm.
Is the fluid level OK?

45RFE AUTO

TRANS

Yes

Go To

14

No

Low fluid level can be the cause of many transmission problems.
If the fluid level is low locate and repair the leak then check and
adjust the fluid level per the service information.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

14

Remove and inspect Transmission Oil Pan per Service Information.
Does it contain excessive debris or contamination?

45RFE AUTO

TRANS

Yes

Repair cause of excessive debris in Transmission Oil Pan.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

15

15

If there are no possible causes remaining, view repair.

45RFE AUTO

TRANS

Repair

If the Transmission is to be repaired, disassemble and inspect the
Valve Body per service information and repair or replace as
necessary. If no problems are found in the valve body, replace the
Solenoid/TRS assembly.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

16

Turn the ignition off to the lock position.
Disconnect the Transmission Control Module harness connector.
Disconnect the Transmission Solenoid /TRS harness connector
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the OD Pressure Switch Sense circuit from the Transmis-
sion Control Module harness connector to the Solenoid/TRS harness connector.
Is the resistance above 5.0 ohms?

45RFE AUTO

TRANS

Yes

Repair the OD Pressure Switch Sense circuit for an open.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

No

Go To

17

190

TRANSMISSION

P1787-OD HYDRAULIC PRESSURE TEST FAILURE —

Continued

 

 

 

 

 

 

 

Content   ..  1105  1106  1107  1108   ..