Jeep Grand Cherokee WJ. Manual - part 1066

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1064  1065  1066  1067   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1066

 

 

7.0

DIAGNOSTIC INFORMATION AND

PROCEDURES

23

Symptom:

*NO RESPONSE FROM TRANSMISSION CONTROL MODULE

POSSIBLE CAUSES

NO RESPONSE FROM TRANSMISSION CONTROL MODULE

FUSED IGNITION SWITCH OUTPUT (RUN/ST) CIRCUIT OPEN

FUSED IGNITION SWITCH OUTPUT (START) CIRCUIT OPEN

FUSED B(+) CIRCUIT OPEN

GROUND CIRCUIT(S) OPEN

OPEN PCI BUS CIRCUIT

TRANSMISSION CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
Note: As soon as one or more module communicates with the DRB, answer
the question.
With the DRB, attempt to communicate with the Airbag Control Module (ACM).
With the DRB, attempt to communicate with the Body Control Module (BCM).
Was the DRB able to I/D or establish communications with either of the modules?

All

Yes

Go To

2

No

Refer to the Communications category and perform the symptom
PCI Bus Communication Failure.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

2

Turn the ignition off.
Disconnect the TCM harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused Ignition Switch
Output (Run/St) circuit.
Note: The light must illuminate brightly, if it does not light, or lights dimly,
the circuit must be repaired. If there is any doubt, compare the brightness
when testing the circuit, to the brightness when connected directly to the
battery positive post.
Is the test light illuminated?

All

Yes

Go To

3

No

Repair the Fused Ignition Switch Output (Run/St) circuit for an
open. Refer to the wiring diagrams location in the Service
Information.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

24

COMMUNICATION

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the TCM harness connector.
Remove the starter relay from the PDC.
Using a 12-volt test light connected to ground, probe the Fused Ignition Switch
Output (Start) circuit.
Note: The light must illuminate brightly, if it does not light, or lights dimly,
the circuit must be repaired. If there is any doubt, compare the brightness
when testing the circuit, to the brightness when connected directly to the
battery positive post.
Observe the test light while momentarily turning the ignition switch to the Start
position.
Is the test light illuminated?

All

Yes

Go To

4

No

Repair the Fused Ignition Switch Output (Start) circuit for an
open. Refer to the wiring diagrams located in the Service Infor-
mation.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

Note: Reinstall the original Starter Relay.

4

Turn the ignition off.
Disconnect the TCM harness connector.
Using a 12-volt test light connected to ground, probe the Fused B(+) circuit.
Note: The light must illuminate brightly, if it does not light, or lights dimly,
the circuit must be repaired. If there is any doubt, compare the brightness
when testing the circuit, to the brightness when connected directly to the
battery positive post.
Is the test light illuminated?

All

Yes

Go To

5

No

Repair the Fused B(+) circuit for an open. Refer to the wiring
diagrams located in the Service Information.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

5

Turn the ignition off.
Disconnect the TCM harness connector.
Using a 12-volt test light connected to 12-volts, probe each ground circuit in the TCM
connector.
NOTE: The light must illuminate brightly, if it does not light, or lights dimly,
the circuit must be repaired. If there is any doubt, compare the brightness
when testing the circuit, to the brightness when connected directly to the
battery negative post.
Is the light illuminated at all ground circuits?

All

Yes

Go To

6

No

Repair the Ground circuit(s) for an open. Check the main ground
connection to engine block and/or chassis. Refer to the wiring
diagrams located in the Service Information.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

25

COMMUNICATION

*NO RESPONSE FROM TRANSMISSION CONTROL MODULE —

Continued

TEST

ACTION

APPLICABILITY

6

Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the TCM harness connector.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
Select DRB Standalone.
Select lab scope.
Select Live.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again
when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the TCM connector.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?

All

Yes

Go To

7

No

Repair the PCI Bus circuit for an open.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

7

If there are no possible causes remaining, view repair.

All

Repair

Replace the Transmission Control Module in accordance with the
Service Information.
Perform 45RFE TRANSMISSION VERIFICATION TEST - VER
1.

26

COMMUNICATION

*NO RESPONSE FROM TRANSMISSION CONTROL MODULE —

Continued

 

 

 

 

 

 

 

Content   ..  1064  1065  1066  1067   ..