Jeep Grand Cherokee WJ. Manual - part 1018

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1016  1017  1018  1019   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 1018

 

 

TEST

ACTION

APPLICABILITY

10

Turn the ignition on.
With the DRBIII

t read DTC’s.

Are any Vehicle Speed Signal codes set?

All

Yes

Go To

11

No

Go To

11

11

Turn the ignition on.
With the DRBIII

t in Inputs/Outputs, read the Speed Control Coast Switch state.

While observing the display, press the Coast Switch several times.
Does the DRBIII

t show the Coast Switch status change appropriately from Pressed

to Released?

All

Yes

Go To

27

No

Replace the Right S/C Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

12

Turn the ignition off.
Disconnect the Speed Control Resume/Accel Switch harness connector.
Turn the ignition on.
With the DRBIII

t, read the Speed Control Switch Voltage.

Did the DRBIII

t show Speed Control Switch Voltage go from below 4.2 Volts to above

4.2 Volts?

All

Yes

Replace the Right Speed Control Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No

Go To

13

13

Turn the ignition on.
With the DRBIII

t read DTC’s.

Are any Vehicle Speed Signal codes set?

All

Yes

Go To

14

No

Go To

14

14

Start the engine.
Allow engine to idle for 1 minute.
Turn the engine off, then turn the ignition on, engine not running.
With the DRBIII

t, actuate the Speed Control Servo Solenoids.

Does the Throttle open and close?

All

Yes

Go To

15

No

Perform Speed Control Vacuum Supply Test per appropriate
service procedure.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

289

SPEED CONTROL

*CHECKING SPEED CONTROL OPERATION WITH NO DTC’S PRESENT

Continued

TEST

ACTION

APPLICABILITY

15

At this time the Speed Control Switch and Servo functions appear to operate
properly.
Using the DRBIII

t, monitor the Speed Control OUTPUT status.

Road test the Vehicle at speeds over 35 MPH (55kmh) and attempt to set the Speed
Control.
The following items will not allow the Speed Control to set. The last or most recent
cause for Speed Control not to set is indicated by the DENIED status.
If ON/OFF Denied message is indicated, the Powertrain Control Module does not see
an ON signal from the Switch.
If SPEED Denied message is indicated, the Vehicle Speed as seen by the Powertrain
Control Module is not greater than 36 MPH.
If RPM Denied message is indicated, the Engine RPM is excessively high.
If BRAKE Denied message is indicated, the Brake Switch Sense Circuit is open
indicating to the PCM that the Brakes are applied. The Sense Circuit is grounded
through the Brake Pedal Switch when the brakes are released.
If P/N Denied message is indicated, Park/Neutral Switch Sense Circuit is grounded
indicating to PCM that Transmission is not in gear. The Sense Circuit is grounded
through the P/N Switch when Transmission is in Park or Neutral.
If RPM/SPD Denied message is indicated, the PCM senses excessive Engine RPM for
a given Vehicle speed.
If SOL FLT Denied message is indicated, the Powertrain Control Module senses a
Servo Solenoid Circuit trouble code that is maturing or set in memory.
Continue if the previous instructions have been completed.

All

Repair

Go To

16

16

Turn the ignition off.
Disconnect the Speed Control Resume/Accel Switch harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Sensor Ground Circuit from the S/C Resume/Accel
harness connector to a good ground.
Is the resistance below 5.0 ohms?

All

Yes

Go To

37

No

Repair the open sensor ground circuit, right S/C switch connector
to the clockspring connector.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

17

Turn the ignition on.
With the DRBIII

t in Inputs/Outputs, read the Speed Control Switch state.

While observing the display, press the On/Off Switch several times.
Does the DRBIII

t show On/Off Switch 9pressed9 and 9released9?

All

Yes

Go To

18

No

Go To

41

18

Turn the ignition off.
Using the Schematics as a guide, inspect the Wiring and Connectors.
Were any problems found?

All

Yes

Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No

Go To

19

290

SPEED CONTROL

*CHECKING SPEED CONTROL OPERATION WITH NO DTC’S PRESENT

Continued

TEST

ACTION

APPLICABILITY

19

Turn the ignition off.
Disconnect the Speed Control Servo harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Ground Circuit at the Servo harness connector to
ground.
Is the resistance below 5.0 ohms?

All

Yes

Go To

20

No

Repair open Ground Circuit at S/C Servo Connector.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

20

Turn the ignition on.
With the DRBIII

t in Inputs/Outputs, read the P/N Switch state.

While observing the display, move the Gear Selector to DRIVE.
Does the DRBIII

t show P/N switch 9D/R9?

All

Yes

Go To

21

No

Go To

21

21

Turn the ignition on.
With the DRBIII

t in Inputs/Outputs, read the Speed Control Set Switch state.

While observing the display, press the Set Switch several times.
Does the DRBIII

t show the Set Switch status change appropriately from Pressed to

Released?

All

Yes

Go To

22

No

Replace the Left S/C Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

22

Turn the ignition off.
Inspect the throttle cable and linkage for any binding or damage.
Is the cable or linkage disconnected or damaged?

All

Yes

Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No

Go To

23

23

Turn the ignition on.
With the DRBIII

t in Inputs/Outputs, read the Speed Control Resume Switch state.

While observing the display, press the Resume Switch several times.
Does the DRBIII

t show the Resume Switch status change appropriately from

Pressed to Released?

All

Yes

Go To

24

No

Go To

32

24

Turn the ignition on.
With the DRBIII

t in Inputs/Outputs, read the Speed Control Cancel Switch state.

While observing the display, press the Cancel Switch several times.
Does the DRBIII

t show the Cancel Switch status change appropriately from Pressed

to Released?

All

Yes

Go To

25

No

Replace the Right S/C Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

291

SPEED CONTROL

*CHECKING SPEED CONTROL OPERATION WITH NO DTC’S PRESENT

Continued

TEST

ACTION

APPLICABILITY

25

Turn the ignition on.
With the DRBIII

t in Inputs/Outputs, read the Speed Control Coast Switch state.

While observing the display, press the Coast Switch several times.
Does the DRBIII

t show the Coast Switch status change appropriately from Pressed

to Released?

All

Yes

Go To

26

No

Replace the Right S/C Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

26

Turn the ignition on.
With the DRBIII

t read DTC’s.

Are any Vehicle Speed Signal codes set?

All

Yes

Go To

27

No

Go To

27

27

Start the engine.
Allow engine to idle for 1 minute.
Turn the engine off, then turn the ignition on, engine not running.
With the DRBIII

t, actuate the Speed Control Servo Solenoids.

Does the Throttle open and close?

All

Yes

Go To

28

No

Perform Speed Control Vacuum Supply Test per appropriate
service procedure.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

28

At this time the Speed Control Switch and Servo functions appear to operate
properly.
Using the DRBIII

t, monitor the Speed Control OUTPUT status.

Road test the Vehicle at speeds over 35 MPH (55kmh) and attempt to set the Speed
Control.
The following items will not allow the Speed Control to set. The last or most recent
cause for Speed Control not to set is indicated by the DENIED status.
If ON/OFF Denied message is indicated, the Powertrain Control Module does not see
an ON signal from the Switch.
If SPEED Denied message is indicated, the Vehicle Speed as seen by the Powertrain
Control Module is not greater than 36 MPH.
If RPM Denied message is indicated, the Engine RPM is excessively high.
If BRAKE Denied message is indicated, the Brake Switch Sense Circuit is open
indicating to the PCM that the Brakes are applied. The Sense Circuit is grounded
through the Brake Pedal Switch when the brakes are released.
If P/N Denied message is indicated, Park/Neutral Switch Sense Circuit is grounded
indicating to PCM that Transmission is not in gear. The Sense Circuit is grounded
through the P/N Switch when Transmission is in Park or Neutral.
If RPM/SPD Denied message is indicated, the PCM senses excessive Engine RPM for
a given Vehicle speed.
If SOL FLT Denied message is indicated, the Powertrain Control Module senses a
Servo Solenoid Circuit trouble code that is maturing or set in memory.
Continue if the previous instructions have been completed.

All

Repair

Go To

29

292

SPEED CONTROL

*CHECKING SPEED CONTROL OPERATION WITH NO DTC’S PRESENT

Continued

 

 

 

 

 

 

 

Content   ..  1016  1017  1018  1019   ..