Jaguar X-Type Sedan and Estate (Wagon). Manual - part 378

DTC

Description

Possible Cause

Action

P096900 Pressure Control

Solenoid C Control
Circuit
Range/Performance

High contact resistance in the
connector terminals between
TCM and transmission
open circuit of internal wiring
for SLC2 control signal circuit
open circuit of internal wiring
for SLC2 ground control signal
circuit
SLC2 pressure control solenoid
no operation
SLC2 pressure control solenoid
stuck
Internal failure in TCM

Check the terminals for corrosion, oxidation between TCM and
transmission. Suspect the TCM, check and install a new TCM as
required, refer to the new module/component installation note at the
top of the DTC Index. Suspect the transmission, check and install a
new transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system

P097000 Pressure Control

Solenoid C Control
Circuit Low

Short to ground of internal
wiring for SLC2 control signal
circuit
Open circuit of internal wiring
for SLC2 control signal circuit
SLC2 pressure control solenoid
no operation
Internal failure in TCM

Suspect the TCM, check and install a new TCM as required, refer to the
new module/component installation note at the top of the DTC Index.
Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system

P097100 Pressure Control

Solenoid C Control
Circuit High

Short to power of internal
wiring for SLC2 control signal
circuit
SLC2 pressure control solenoid
no operation
Internal failure in TCM

P097300 Shift Solenoid A

Control Circuit Low

Short to ground of internal
wiring for S1 shift solenoid 1
S1 shift solenoid 1 not
working
Internal failure in TCM

P097400 Shift Solenoid A

Control Circuit High

High contact resistance in the
connector terminals between
TCM and transmission
Open circuit of internal wiring
for S1 shift solenoid 1
S1 shift solenoid 1 not
working
Short to power of internal
wiring for S1 shift solenoid 1
Internal failure in TCM

P097600 Shift Solenoid B

Control Circuit Low

Short to ground of internal
wiring for S2 shift solenoid 2
S2 shift solenoid 2 not
working
Internal failure in TCM

P097700 Shift Solenoid B

Control Circuit High

High contact resistance in the
connector terminals between
TCM and transmission
Open circuit of internal wiring
for S2 shift solenoid 2
S2 shift solenoid 2 not
working
Short to power of internal
wiring for S2 shift solenoid 2
Internal failure in TCM

P171900 Engine Torque Signal

CAN message, engine torque
signal has not been updated
CAN message, engine torque
signal quality factor equals
zero

Check for ECM DTCs. Rectify as required

P173D00 Ignition Key Lock

Solenoid Circuit /
Open

Open circuit between ignition
switch keylock solenoid and
GSM

Carry out any diagnostic pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the electrical
guides and check for open circuit between ignition switch keylock
solenoid and GSM

P173E00 Ignition Key Lock

Solenoid Circuit Low

Short to ground between
ignition switch keylock
solenoid and GSM

Carry out any diagnostic pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the electrical
guides and check for short to ground between ignition switch keylock
solenoid and GSM

P173F00 Ignition Key Lock

Solenoid Circuit High

Short to power between
ignition switch keylock
solenoid and GSM

Carry out any diagnostic pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the electrical
guides and check for short to power between ignition switch keylock
solenoid and GSM

P178368 Transmission

Overtemperature
Condition

Event information. System
event not caused by the TCM,
but requiring the TCM to
record this DTC
Transmission fluid level low
Transmission fluid
cooler/hoses are

Check the transmission fluid level and condition, correct as required.
Check the transmission fluid cooler hoses for signs of
obstruction/damage/blockage, correct as required. Check the engine
cooling system and engine cooling fans operation. Suspect the
transmission, check and install a new transmission as required, refer
to the new module/component installation note at the top of the DTC
Index. Refer to service routines at the top of the DTC Index and carry

DTC

Description

Possible Cause

Action

obstructed/damaged/blocked
Mechanical failure of
transmission
Transmission has been
exposed to excessive high
load and high ambient
temperature greater than 150
degrees C (302 degrees F)

out service routines as required using the manufacturer approved
diagnostic system

P179900 CAN TCM/ABS Circuit

Malfunction

Vehicle speed message has
not been updated on CAN
ABS malfunction

Carry out any diagnostic pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Check ABS for DTCs
rectify as required

P215800 Vehicle Speed Sensor

Open circuit of internal wiring
NIN+ input speed sensor
circuit
Short circuit to ground of
internal wiring NIN+ input
speed sensor circuit
Input speed sensor failure
Internal failure in TCM

Check the terminals for corrosion, oxidation between TCM and
transmission. Check NIN+ circuit for open circuit, short to ground.
Replace Input speed sensor. Suspect the TCM, check and install a new
TCM as required, refer to the new module/component installation note
at the top of the DTC Index. Refer to service routines at the top of
the DTC Index and carry out service routines as required using the
manufacturer approved diagnostic system

P271900 Pressure Control

Solenoid D Control
Circuit
Range/Performance

High contact resistance in the
connector terminals between
TCM and transmission
SLC3 pressure control solenoid
stuck
open circuit of internal wiring
for SLC3 control signal circuit
open circuit of internal wiring
for SLC3 ground control signal
circuit
SLC3 pressure control solenoid
no operation
Internal failure in TCM

P272000 Pressure Control

Solenoid D Control
Circuit Low

High contact resistance in the
connector terminals between
TCM and transmission
Short to ground of internal
wiring for SLC3 control signal
circuit
Open circuit of internal wiring
for SLC3 control signal circuit
SLC3 pressure control solenoid
no operation
Internal failure in TCM

P272100 Pressure Control

Solenoid D Control
Circuit High

Short to power of internal
wiring for SLC3 control signal
circuit
SLC3 pressure control solenoid
no operation
Internal failure in TCM

P272800 Pressure Control

Solenoid E Control
Circuit
Range/Performance

High contact resistance in the
connector terminals between
TCM and transmission
Open circuit of internal wiring
for SLB1 control signal circuit
Open circuit of internal wiring
for SLB1 ground control signal
circuit
SLB1 pressure control solenoid
no operation
SLB1 pressure control solenoid
stuck
Internal failure in TCM

P272900 Pressure Control

Solenoid E Control
Circuit Low

P273000 Pressure Control

Solenoid E Control
Circuit High

Short to power of internal
wiring for SLB1 control signal
circuit
SLB1 pressure control solenoid
no operation
Internal failure in TCM

DTC

Description

Possible Cause

Action

P273300 Pressure Control

Solenoid F Stuck On

SLC1 pressure control not
engaged in drive
Mechanical fault in the
transmission

Suspect the transmission, check and install a new transmission as
required, refer to the new module/component installation note at the
top of the DTC Index. Refer to service routines at the top of the DTC
Index and carry out service routines as required using the
manufacturer approved diagnostic system

P273700 Pressure Control

Solenoid F Control
Circuit
Range/Performance

High contact resistance in the
connector terminals between
TCM and transmission
Open circuit of internal wiring
for SLC1 control signal circuit
Open circuit of internal wiring
for SLC1 ground control signal
circuit
SLC1 pressure control solenoid
no operation
SLC1 pressure control solenoid
stuck
Internal failure in TCM

P273800 Pressure Control

Solenoid F Control
Circuit Low

P273900 Pressure Control

Solenoid F Control
Circuit High

Short to power of internal
wiring for SLC1 control signal
circuit
SLC1 pressure control solenoid
no operation
Internal failure in TCM

P278368 Torque Converter

Temperature Too High

Event information. System
event not caused by the TCM,
but requiring the TCM to
record this DTC
Torque converter temperature
greater than 170 degrees C
(338 degrees F)

Check the transmission fluid level and condition. Check the
transmission fluid cooler/hoses for signs of obstruction, damage,
blockage. Suspect the transmission, check and install a new
transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system

P278768 Clutch Temperature

Too High

Event information. System
event not caused by the TCM,
but requiring the TCM to
record this DTC
Torque converter stalled
The transmission fluid
temperature is the same, or
greater than 120 degrees C
(248 degrees F) for longer
than 5 seconds
The transmission fluid
temperature is greater than
120 degrees C and lower than
150 degrees C (302 degrees F)
for longer than 4 seconds
The transmission fluid
temperature is greater than
150 degrees (302 degrees F)
for longer than 3 seconds
Internal failure in TCM

P280000 Transmission Range

Sensor B Circuit
(PRNDL Input)

Incorrect adjustment of gear
position sensor
Internal failure in TCM

Check the gear selector lever is adjusted correctly. Suspect the TCM,
check and install a new TCM as required, refer to the new
module/component installation note at the top of the DTC Index.
Refer to service routines at the top of the DTC Index and carry out
service routines as required using the manufacturer approved
diagnostic system

P280100 Transmission Range

Sensor B Circuit
Range/Performance

Undefined range when drive
selected
Incorrect adjustment of gear
position sensor
Internal failure in TCM

Check the gear selector lever is adjusted correctly. Suspect the TCM,
GSM or transmission check and install a new TCM, GSM or
transmission as required, refer to the new module/component
installation note at the top of the DTC Index. Refer to service routines
at the top of the DTC Index and carry out service routines as required
using the manufacturer approved diagnostic system

P280500 Transmission Range

Sensor A / B
Correlation

Incorrect adjustment of gear
position sensor
Internal failure in TCM

U000100 High Speed CAN

Communication Bus

CAN bus open circuit
CAN bus short circuit to
ground
CAN bus short circuit to power
Internal fault in another
control module in the same

Carry out any diagnostic pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the electrical
guides and check CAN circuit for open circuit, short to ground, short to
power. Suspect the TCM, check and install a new TCM as required,
refer to the new module/component installation note at the top of the
DTC Index. Refer to service routines at the top of the DTC Index and

DTC

Description

Possible Cause

Action

part of the CAN network
Internal failure in TCM

carry out service routines as required using the manufacturer approved
diagnostic system

U210511 Switch Pack Signal "A"

Circuit short to ground. The
TCM has detected a ground
measurement for a period
longer than expected or has
detected a ground
measurement when another
value was expected
Shiftlock solenoid circuit short
to ground
GSM internal failure

Refer to the electrical guides and check shiftlock circuit for short to
ground. Suspect the GSM, check and install a new GSM as required,
refer to the new module/component installation note at the top of the
DTC Index

U210512 Switch Pack Signal "A"

Circuit short to power. The
TCM has detected a vehicle
power measurement for a
period longer than expected or
has detected a vehicle power
measurement when another
value was expected
Shiftlock solenoid circuit short
to power
Open circuit shiftlock solenoid
circuit
GSM internal failure

Refer to the electrical guides and check shiftlock circuit for short to
power, open circuit. Suspect the GSM, check and install a new GSM as
required, refer to the new module/component installation note at the
top of the DTC Index

Content .. 376 377 378 379 ..