Infiniti G Sedan (2013 year). Manual - part 8

 

  Index      Infiniti     Infiniti G Sedan (2013 year) - manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     6      7      8      9     ..

 

 

Infiniti G Sedan (2013 year). Manual - part 8

 

 

Black plate (120,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

2-42

Instruments and controls

“Vehicle Dynamic Control (VDC) system”
(P.5-58).)

SIC3325

If the power supply is disconnected, the
clock will not indicate the correct time.
Readjust the time.

ADJUSTING THE TIME

1. To set the clock forward, push the

button

*

1

.

2. To set the clock backward, push the

button

*

2

.

3. To move forward or backward faster,

push and hold the button more than 5
seconds.

For details about display clock adjustment
(if so equipped), see “How to use SETTING
button” (P.4-14).

JVI0329X

Automatic transmission models

SIC4684

Manual transmission models

CLOCK

POWER OUTLET

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (121,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

SIC4316

Automatic transmission models

The power outlet is located in the center
console and storage box (if so equipped).

CAUTION

.

The outlet and plug may be hot during or
immediately after use.

.

Do not use with accessories that exceed
a 12 volt, 120W (10A) power draw. Do
not use double adapters or more than
one electrical accessory.

.

Use power outlet with the engine run-
ning to avoid discharging the vehicle
battery.

.

Avoid using power outlet when the air
conditioner, headlights or rear window
defroster is on.

.

This power outlet is not designed for use
with a cigarette lighter unit.

.

Push the plug in as far as it will go. If
good contact is not made, the plug may
overheat or the internal temperature
fuse may blow.

.

Before inserting or disconnecting a plug,
be sure the electrical accessory being
used is turned OFF.

.

When not in use, be sure to close the
cap. Do not allow water or any liquid to
contact the outlet.

SIC3219

FRONT

To open the ashtray lid, push the lid down
and release it

*

1

.

To empty the ashtray, pull out

*

2

.

The cigarette lighter operates when the
ignition switch is in the ON position.

Push the lighter in all the way

*

3

, then

release it. When the lighter is heated, it will
spring out. Return the lighter to its original
position after use.

Instruments and controls

2-43

CIGARETTE LIGHTER AND ASHTRAYS (if so
equipped)

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (122,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

2-44

Instruments and controls

CAUTION

.

The cigarette lighter socket is a power
source for the cigarette lighter element
only. The use of the cigarette lighter
socket as a power source for any other
accessory is not recommended.

.

Do not use any other power outlet for an
accessory lighter.

SIC2570

Manual transmission models

REAR

To open the ashtray, pull the lid down

*

1

.

To empty the ashtray, push down

*

2

, and

pull out.

CUP HOLDERS

CAUTION

.

Avoid abrupt starting and braking when
the cup holder is being used to prevent
spilling the drink. If the liquid is hot, it
can scald you or your passenger.

.

Use only soft cups in the cup holder.
Hard objects can injure you in an
accident.

STORAGE

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (123,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

SIC4689

Automatic transmission models — Front

To open the cup holder, push the lid

*

1

.

The flap

*

A

will be folded down when

inserting a large container.

SIC3925

Manual transmission models — Front

To open the cup holder, slide the lid

*

1

.

Install the partition plate into the slit

*

2

.

SIC1846B

Rear

To open the cup holder, pull the lid.

Instruments and controls

2-45

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (124,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

2-46

Instruments and controls

SIC3276

Sedan

SIC3462

Coupe

Soft bottle holder

CAUTION

.

Do not use bottle holder for any other
objects that could be thrown about in
the vehicle and possibly injure people
during sudden braking or an accident.

.

Do not use bottle holder for open liquid
containers.

SIC3246

SUNGLASSES HOLDER

WARNING

Keep the sunglasses holder closed while
driving to prevent an accident.

To open the sunglasses holder, push

*

1

.

CAUTION

.

Do not use for anything other than
glasses.

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (125,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

.

Do not leave glasses in the sunglasses
holder while parking in direct sunlight.
The heat may damage the glasses.

SIC3469

GLOVE BOX

WARNING

Keep glove box lid closed while driving to
help prevent injury in an accident or a
sudden stop.

To open the glove box, pull the handle

*

1

.

To close, push the lid in until the lock
latches.

To lock

*

2

/unlock

*

3

the glove box, use

the mechanical key. For the mechanical key
usage, see “Keys” (P.3-2).

SIC4363

Automatic transmission models

SIC4307

Manual transmission models

Instruments and controls

2-47

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (126,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

2-48

Instruments and controls

CONSOLE BOX

To open the console boxes, push the knob

*

A

and pull up the lid.

To close, push the lid down until latched.

The inner tray (if so equipped) can be
moved to the front or rear position.

SIC3468

Coupe — Manual transmission model

Removing the console lid (model
with manual transmission)

To remove the console lid:

1. Remove the hinge mask

*

A

using a

screwdriver wrapped with a cloth.

2. Loosen four screws, and remove the lid.

3. Tighten the two outside screws

*

B

.

4. Install the removed hinge mask

*

A

to

the original position.

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (127,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

SIC3928

Type A

SIC3929

Type B

SIC3927A

Type C

CARD HOLDER (if so equipped)

The card holder is located on or behind the
driver’s or passenger’s sun visor.

To use the card holder, slide the card in the
card holder.

SIC4308

STORAGE BOX (if so equipped)

To open, push the storage box lid

*

1

as

illustrated.

Do not place valuable items in the storage
box.

Do not use the storage box as an ashtray.

Instruments and controls

2-49

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (128,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

2-50

Instruments and controls

SIC3248

Sedan

COAT HOOKS

Sedan

The coat hooks are equipped beside the
rear personal lights.

CAUTION

Do not place items which are more than 2 lb
(1 kg) on the hook.

SIC3544

Coupe

Coupe

To use the coat hook, push the hook

*

A

to

release.

CAUTION

Avoid hanging heavy goods on the hook.

SIC3467

STOWING GOLF BAGS (Coupe)

Normally, two standard golf bags can be
stowed in the trunk. Insert the top of the
golf bag into left side of the trunk room

*

1

then put the bag forward

*

2

. Insert the top

of the 2nd golf bag into right side of the
trunk room

*

3

and pull it in all the way

*

4

.

In some cases, you may not be able to stow
two golf bags in your vehicle, depending
on their sizes or types.

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (129,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

SIC3320

CARGO NET RETAINERS

The cargo net helps keep packages in the
cargo area from moving around while your
vehicle is driven.

To install the cargo net, attach the hooks to
the retainers

*

A

.

CAUTION

Avoid keeping heavy objects in the net.

SIC3317

TRUNK NET FOR EXTRA WINDOW
WASHER FLUID (Canada only; if so
equipped)

The trunk net is provided for holding a tank
of extra window washer fluid.

To install the net, place a commercially
available tank in the right corner of the
trunk and then attach the hooks to the
restrainers

*

A

.

POWER WINDOWS

WARNING

.

Make sure that all passengers have their
hands, etc. inside the vehicle while it is
in motion and before closing the win-
dows. Use the window lock switch to
prevent unexpected use of the power
windows.

.

Do not leave children unattended inside
the vehicle. They could unknowingly
activate switches or controls and be-
come trapped in the window. Unat-
tended children could become involved
in serious accidents.

The power windows operate when the
ignition switch is in the ON position or for
about 45 seconds after the ignition switch
is pushed to the OFF position. If the
driver’s or front passenger’s door is
opened during this period of about 45
seconds, power to the windows is can-
celed.

Instruments and controls

2-51

WINDOWS

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (130,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

2-52

Instruments and controls

SIC3279

Sedan

SIC3286A

Coupe

Main power window switch (driver’s
side)

1.

Driver side window

2.

Front passenger side window

3.

Rear left passenger side window
(Sedan only)

4.

Rear right passenger side window
(Sedan only)

5.

Window lock button

To open or close the window, push down

*

A

or pull up

*

B

the switch and hold it.

The main switch (driver side switches) will
open or close all the windows.

Locking passengers’ windows

When the lock button

*

C

is pushed in, only

the driver side window can be opened or
closed. Push it in again to cancel.

SIC3241

Passenger side power window
switch

The passenger side switch will open or
close only the corresponding window. To
open or close the window, push down or
pull up the switch and hold it.

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (131,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

SIC3289

Sedan — Type A

SIC3285

Sedan — Type B

SIC3288

Coupe

Automatic operation (for front door
windows or all door windows)

To fully open or close the window, com-
pletely push down or pull up the switch
and release it; it need not be held. The
window will automatically open or close all
the way. To stop the window, just push or
lift the switch in the opposite direction.

A light push or pull on the switch will cause
the window to open or close until the
switch is released.

Auto reverse function

WARNING

There are some small distances immediately
before the closed position which cannot be
detected. Make sure that all passengers
have their hands, etc., inside the vehicle
before closing the window.

If the control unit detects something
caught in the window as it is closing, the
window will be immediately lowered.

The auto reverse function can be activated
when the window is closed by automatic
operation when the ignition switch is in the
ON position or for 45 seconds after the
ignition switch is pushed to the OFF
position.

Depending on the environment or driving
conditions, the auto reverse function may
be activated if an impact or load similar to
something being caught in the window
occurs.

Instruments and controls

2-53

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (132,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

2-54

Instruments and controls

Automatic adjusting function
(Coupe)

CAUTION

When the battery cable is removed from the
battery terminal, do not close either of the
front doors. The automatic window adjust-
ing function will not work and the side roof
panel may be damaged.

The power window has an automatic
adjusting function. When the door is being
opened, the window is automatically low-
ered slightly to avoid contact between the
window and the side roof panel. When the
door is closed, the window is automatically
raised slightly.

While the automatic adjusting function
does not work, the window will be con-
trolled as follows:

. When the door is opened, the window

lowers for approximately 2 seconds.

. While the door is open, the window

cannot be raised.

If the windows do not close auto-
matically

If the power window automatic function
(closing only) does not operate properly,
perform the following procedure to initi-
alize the power window system.

1. Push the ignition switch to the ON

position.

2. Close the door.

3. Open the window completely by oper-

ating the power window switch.

4. Pull the power window switch and hold

it to close the window, and then hold
the switch more than 3 seconds after
the window is closed completely.

5. Release the power window switch.

Operate the window by the automatic
function to confirm the initialization is
complete.

6. Perform steps 2 through 5 above for

other windows.

If the power window automatic function
does not operate properly after performing
the procedure above, have your vehicle
checked by an INFINITI retailer.

WARNING

.

In an accident you could be thrown from
the vehicle through an open moonroof.
Always use seat belts and child re-
straints.

.

Do not allow anyone to stand up or
extend any portion of their body out of
the moonroof opening while the vehicle
is in motion or while the moonroof is
closing.

CAUTION

.

Remove water drops, snow, ice or sand
from the moonroof before opening.

.

Do not place any heavy object on the
moonroof or surrounding area.

MOONROOF (if so equipped)

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (133,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

AUTOMATIC MOONROOF

The moonroof only operates when the
ignition switch is in the ON position.

The automatic moonroof is operational for
about 45 seconds, even if the ignition
switch is pushed to the OFF position. If the
driver’s door or the passenger’s door is
opened during this period of about 45
seconds, power to the moonroof is can-
celed.

SIC3243

Sunshade

The sunshade will open automatically
when the moonroof is opened. However,
it must be closed manually.

Tilting the moonroof

To tilt up, first close the moonroof, then
push the UP

*

1

side of the moonroof

switch and release it; it need not be held.
To tilt down the moonroof, push the DOWN

*

2

side.

Sliding the moonroof

To fully open or close the moonroof, push
the CLOSE

*

1

or OPEN

*

2

side of

the moonroof switch and release it; it need
not be held. The roof will automatically
open or close all the way. To stop the roof,
push the switch once more while it is
opening or closing.

Auto reverse function

WARNING

There are some small distances immediately
before the closed position which cannot be
detected. Make sure that all passengers
have their hands, etc., inside the vehicle
before closing the moonroof.

If the control unit detects something
caught in the moonroof when it is closing,
the moonroof will be immediately opened.

The auto reverse function can be activated
when the moonroof is closed by automatic
operation when the ignition switch is in the
ON position or for about 45 seconds after
the ignition switch is pushed to the OFF
position.

If the moonroof cannot be closed auto-
matically when the auto reverse function
activates due to a malfunction, push and
hold the CLOSE

*

1

side of the

Instruments and controls

2-55

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (134,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

2-56

Instruments and controls

moonroof switch.

Depending on the environment or driving
conditions, the auto reverse function may
be activated if an impact or load similar to
something being caught in the moonroof
occurs.

If the moonroof does not operate

If the moonroof does not operate properly,
perform the following procedure to initi-
alize the moonroof operation system.

1. If the moonroof is open, close it fully by

repeatedly pushing the CLOSE

*

1

side of the moonroof switch to tilt the
moonroof up.

2. Push and hold the CLOSE

*

1

side

of the moonroof switch.

3. Release the moonroof switch after the

moonroof moves slightly up and down.

4. Push and hold the OPEN

*

2

side of

the moonroof switch to fully tilt the
moonroof down.

5. Check if the moonroof switch operates

normally.

If the moonroof does not operate properly
after performing the procedure above, have
your vehicle checked by an INFINITI retailer.

SIC3249

MAP LIGHTS

Push the button as illustrated to turn the
light on or off.

SIC3250

PERSONAL LIGHTS (Sedan)

Rear

Push the button as illustrated to turn the
light on or off.

INTERIOR LIGHTS

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Black plate (135,1)

[ Edit: 2012/ 7/ 6 Model: V36-D ]

SIC3251

INTERIOR LIGHT CONTROL SWITCH

The interior light control switch has three
positions: ON, DOOR and OFF.

ON position

When the switch is in the ON position

*

1

the map lights and rear personal lights will
illuminate.

DOOR position

When the switch is in the DOOR position

*

2

, the map lights and rear personal lights

will illuminate under the following condi-
tions:

. ignition switch is switched to the LOCK

position
— remain on for about 15 seconds.

. doors are unlocked by pushing the

UNLOCK button on the Intelligent Key
or door handle request switch with the
ignition switch in the LOCK position
— remain on for about 15 seconds.

. any door is opened and then closed

with the ignition switch in the LOCK
position
— remain on for about 15 seconds.

. any door is opened with the ignition

switch in the ACC or ON position
— remain on while the door is opened.

When the door is closed, the lights
go off.

The lights will also turn off after a period
of time when the lights remain illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.

When the auto interior illumination is set
to the OFF position (see “Vehicle informa-
tion and settings” (P.4-9)), 
the lights will
illuminate under the following condition:

. any door is opened with the ignition

switch in any position

— remain on while the door is opened.

When the door is closed, the lights
go off.

OFF position

When the switch is in the OFF position

*

3

,

the lights will not illuminate, regardless of
the condition.

CAUTION

Do not use for extended periods of time with
the engine stopped. This could result in a
discharged battery.

Instruments and controls

2-57

Condition:

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     6      7      8      9     ..