Infiniti QX56 (JA60). Manual - part 946

TM-86

< COMPONENT DIAGNOSIS >

P1762 DIRECT CLUTCH SOLENOID

P1762 DIRECT CLUTCH SOLENOID

Description

INFOID:0000000005148654

Direct clutch solenoid valve is controlled by the TCM in response to signals sent from the transmission range

switch, output speed sensor and accelerator pedal position sensor. Gears will then be shifted to the optimum

position.

CONSULT-III Reference Value in Data Monitor Mode

INFOID:0000000005148655

On Board Diagnosis Logic

INFOID:0000000005148656

• This is an OBD-II self-diagnostic item.

• Diagnostic trouble code “P1762 DRCT CLUTCH SOLENOID” with CONSULT-III is detected under the fol-

lowing conditions.

- When TCM detects an improper voltage drop when it tries to operate the solenoid valve.

- When TCM detects as irregular by comparing target value with monitor value.

Possible Cause

INFOID:0000000005148657

• Harness or connectors

(The solenoid circuit is open or shorted.)

• Direct clutch solenoid valve 

DTC Confirmation Procedure

INFOID:0000000005148658

NOTE:

If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”

and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-III

1. Turn ignition switch “ON”. (Do not start engine.)

2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3. Start engine.

4. Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.

ACCELE POSI: 1.5/8 - 2.0/8

SLCT LVR POSI: “D” position 

GEAR: 1st 

⇒ 2nd (D/C ON/OFF)

Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving

conditions required for this test.

5. If DTC is detected, go to 

TM-86, "Diagnosis Procedure"

.

 WITH GST

Follow the procedure “With CONSULT-III”.

Diagnosis Procedure

INFOID:0000000005148659

1.

CHECK INPUT SIGNAL

With CONSULT-III

1. Turn ignition switch “ON”. 

2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3. Start the engine.

4. Read out the value of “D/C SOLENOID” while driving.

Item name

Condition 

Display value (Approx.)

D/C SOLENOID

Direct clutch disengaged. Refer to 

TM-9

.

0.6 - 0.8 A

Direct clutch engaged. Refer to 

TM-9

.

0 - 0.05 A

P1762 DIRECT CLUTCH SOLENOID

TM-87

< COMPONENT DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 2.

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-94, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTIONING ITEM

Check the following items:

• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> Replace the control valve with TCM. Refer to 

TM-172, "Control Valve with TCM and A/T Fluid

Temperature Sensor 2 and Plug"

.

NG

>> Repair or replace damaged parts.

4.

CHECK DTC

Perform “DTC Confirmation Procedure”.

• Refer to 

TM-86, "DTC Confirmation Procedure"

.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 2.

Item name

Condition 

Display value (Approx.)

D/C SOLENOID

Direct clutch disengaged. Refer to 

TM-9

.

0.6 - 0.8 A

Direct clutch engaged. Refer to 

TM-9

.

0  -  0.05  A

TM-88

< COMPONENT DIAGNOSIS >

P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID

P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID

Description

INFOID:0000000005148660

High and low reverse clutch solenoid valve is controlled by the TCM in response to signals sent from the trans-

mission range switch, output speed sensor and accelerator pedal position sensor. Gears will then be shifted to

the optimum position.

CONSULT-III Reference Value in Data Monitor Mode

INFOID:0000000005148661

On Board Diagnosis Logic

INFOID:0000000005148662

• This is an OBD-II self-diagnostic item.

• Diagnostic trouble code “P1767 HLR CLUTCH SOLENOID” with CONSULT-III or is detected under the fol-

lowing conditions.

- When TCM detects an improper voltage drop when it tries to operate the solenoid valve.

- When TCM detects as irregular by comparing target value with monitor value.

Possible Cause

INFOID:0000000005148663

• Harness or connectors

(The solenoid circuit is open or shorted.)

• High and low reverse clutch solenoid valve 

DTC Confirmation Procedure

INFOID:0000000005148664

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”

and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-III

1. Turn ignition switch “ON”. (Do not start engine.)

2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3. Start engine.

4. Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.

ACCELE POSI: 1.5/8 - 2.0/8

SLCT LVR POSI: “D” position 

GEAR: 2nd 

⇒ 3rd (HLR/C ON/OFF)

Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving

conditions required for this test.

5. If DTC is detected, go to 

TM-88, "Diagnosis Procedure"

.

 WITH GST

Follow the procedure “With CONSULT-III”.

Diagnosis Procedure

INFOID:0000000005148665

1.

CHECK INPUT SIGNAL

With CONSULT-III

1. Turn ignition switch “ON”. 

2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3. Start the engine.

4. Read out the value of “HLR/C SOLENOID” while driving.

Item name

Condition 

Display value (Approx.)

HLR/C SOL

High and low reverse clutch disengaged. Refer to 

TM-9

.

0.6 - 0.8 A

High and low reverse clutch engaged. Refer to 

TM-9

.

0 - 0.05 A

P1767 HIGH AND LOW REVERSE CLUTCH SOLENOID

TM-89

< COMPONENT DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 2.

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit Refer to 

TM-94, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTIONING ITEM

Check the following items:

• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> Replace the control valve with TCM. Refer to 

TM-172, "Control Valve with TCM and A/T Fluid

Temperature Sensor 2 and Plug"

.

NG

>> Repair or replace damaged parts.

4.

CHECK DTC

Perform “DTC Confirmation Procedure”.

• Refer to 

TM-88, "DTC Confirmation Procedure"

.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 2.

Item name

Condition 

Display value (Approx.)

HLR/C SOL

High and low reverse clutch disengaged. Refer to 

TM-9

.

0.6 - 0.8 A

High and low reverse clutch engaged. Refer to 

TM-9

.

0 - 0.05 A