Infiniti QX56 (JA60). Manual - part 818

 

  Index      Infiniti     Infiniti QX56 (JA60) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  816  817  818  819   ..

 

 

Infiniti QX56 (JA60). Manual - part 818

 

 

SUSPENSION CONTROL SYSTEM INOPERATIVE

SCS-37

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

SCS

N

O

P

SUSPENSION CONTROL SYSTEM INOPERATIVE

Description

INFOID:0000000005148194

The suspension control system does not activate.  It does not raise or lower the vehicle in response to ride

height changes. 

Diagnosis Procedure

INFOID:0000000005148195

1.

SUSPENSION CONTROL UNIT POWER AND GROUND INSPECTION

Check the suspension control unit power and ground supply. Refer to 

SCS-17, "SUSPENSION CONTROL

UNIT : Diagnosis Procedure"

.

Does the suspension control unit power and ground pass inspection?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK HEIGHT SENSOR SIGNAL INPUT

CONSULT-III DATA MONITOR

1. Turn ignition switch ON.

2. Select "HEIGT SEN" of AIR LEVELIZER data monitor item.

3. Check the monitor status.

Is the height sensor voltage normal?

YES

>> GO TO 3.

NO

>> Check height sensor signal circuit. Refer to 

SCS-23, "Diagnosis Procedure"

 .

3.

CHECK GENERATOR "L" CIRCUIT SIGNAL

CONSULT-III DATA MONITOR

1. Start the engine.

2. Select "ACG L" of AIR LEVELIZER data monitor item.

3. Check the monitor status.

Is the generator "L" signal operating normally?

YES

>> GO TO 4.

NO

>> Check generator L circuit. Refer to 

CHG-12, "Diagnosis Procedure"

.

4.

SUSPENSION AIR COMPRESSOR POWER AND GROUND INSPECTION

Check the suspension air compressor power and ground supply. Refer to 

SCS-17, "SUSPENSION AIR COM-

PRESSOR : Diagnosis Procedure"

.

Does the suspension air compressor power and ground pass inspection?

YES

>> System is operating normally.

NO

>> Repair or replace the malfunctioning part.

HEIGT SEN

: 0.2V - 4.8V

ACG L

: OFF with charge light OFF
: ON with charge light ON

SCS-38

< SYMPTOM DIAGNOSIS >

SUSPENSION CONTROL SYSTEM DOES NOT RAISE

SUSPENSION CONTROL SYSTEM DOES NOT RAISE

Description

INFOID:0000000005148196

The suspension control system does not raise the vehicle in accordance with ride height changes. 

Diagnosis Procedure

INFOID:0000000005148197

1.

SUSPENSION CONTROL UNIT POWER AND GROUND INSPECTION

Check the suspension control unit power and ground supply. Refer to 

SCS-17, "SUSPENSION CONTROL

UNIT : Diagnosis Procedure"

.

Does the suspension control unit power and ground pass inspection?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK HEIGHT SENSOR SIGNAL INPUT

CONSULT-III DATA MONITOR

1. Turn ignition ON.

2. Select "HEIGT SEN" of AIR LEVELIZER data monitor item.

3. Check the monitor status.

Is the height sensor voltage normal?

YES

>> GO TO 3.

NO

>> Check height sensor signal circuit. Refer to 

SCS-23, "Diagnosis Procedure"

 .

3.

SUSPENSION AIR COMPRESSOR POWER AND GROUND INSPECTION

Check the suspension air compressor power and ground supply. Refer to 

SCS-17, "SUSPENSION AIR COM-

PRESSOR : Diagnosis Procedure"

.

Does the suspension air compressor power and ground pass inspection?

YES

>> Inspect for a weak compressor, leak or restriction in the system. Repair or replace malfunctioning

part. 

NO

>> Repair or replace the malfunctioning part.

HEIGT SEN

: 0.2V - 4.8V

SUSPENSION CONTROL SYSTEM DOES NOT LOWER

SCS-39

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

SCS

N

O

P

SUSPENSION CONTROL SYSTEM DOES NOT LOWER

Description

INFOID:0000000005148198

The suspension control system does not lower the vehicle in accordance with ride height changes. 

Diagnosis Procedure

INFOID:0000000005148199

1.

SUSPENSION CONTROL UNIT POWER AND GROUND INSPECTION

Check the suspension control unit power and ground supply. Refer to 

SCS-17, "SUSPENSION CONTROL

UNIT : Diagnosis Procedure"

.

Does the suspension control unit power and ground pass inspection?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK HEIGHT SENSOR SIGNAL INPUT

CONSULT-III DATA MONITOR

1. Turn ignition ON.

2. Select "HEIGT SEN" of AIR LEVELIZER data monitor item.

3. Check the monitor status.

Is the height sensor voltage normal?

YES

>> GO TO 3.

NO

>> Check height sensor signal circuit. Refer to 

SCS-23, "Diagnosis Procedure"

 .

3.

EXHAUST VALVE SOLENOID CIRCUIT INSPECTION

Check the exhaust valve solenoid circuit. Refer to 

SCS-24, "Component Function Check"

.

Does the exhaust valve solenoid circuit pass inspection?

YES

>> Inspect for a restriction in the system. repair or replace the malfunctioning part. 

NO

>> Repair or replace the malfunctioning part.

HEIGT SEN

: 0.2V - 4.8V

SCS-40

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000005383225

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along

with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain

types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS

system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front

air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

Information necessary to service the system safely is included in the SR and SB section of this Service Man-

ual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by

an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag

Module, see the SR section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-

ness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-

tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a

hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing

serious injury.

• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Precaution for Rear Suspension

INFOID:0000000005148201

• When installing the rubber bushings, the final tightening must be done under unladen condition and with the

tires on level ground. Oil will shorten the life of the rubber bushings, so wipe off any spilled oil immediately.

• Unladen condition means the fuel tank, engine coolant and lubricants are at the full specification. The spare

tire, jack, hand tools, and mats are in their designated positions.

• After installing suspension components, check the wheel alignment.

• Caulking nuts are not reusable. Always use new caulking nuts for installation. New caulking nuts are pre-

oiled, do not apply any additional lubrication.

 

 

 

 

 

 

 

Content   ..  816  817  818  819   ..