Infiniti QX56 (Z62). Manual - part 1303

P0732 2GR INCORRECT RATIO

TM-121

< DTC/CIRCUIT DIAGNOSIS >

[7AT: RE7R01B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

3.

Keep the current driving status for 2 seconds or more if CONSULT-III screen changes from “OUT OF
CONDITION” to “TESTING”.

CAUTION:

When “TESTING” is not indicated on CONSULT-III for a long time, check “Self Diagnostic Results”
in “TRANSMISSION”. When a DTC other than “P0732” is detected, check the DTC. Refer to 

TM-78,

"DTC Index"

.

 With GST

1.

Drive vehicle and maintain the following conditions for 2 seconds or more.

2.

Check DTC.

Is  “OUT OF CONDITION”,  “STOP VEHICLE” or “COMPLETED RESULT NG” displayed? / Is “P0732”
detected?

YES-1 (OUT OF CONDITION)>>Perform “Step 3” again.
YES-2 (STOP VEHICLE)>>GO TO 4.
YES-3 (COMPLETED RESULT NG)>>Go to 

TM-121, "Diagnosis Procedure"

.

YES-4 (“P0732” is detected)>>Go to 

TM-121, "Diagnosis Procedure"

.

NO

>> GO TO 4.

4.

CHECK SYMPTOM (PART 2)

1.

Stop vehicle.

2.

Drive vehicle in “D” position allowing it to shift from 1GR to 7GR and check shift timing and shift shock.

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006226826

1.

DETECT MALFUNCTIONING ITEM

Disassemble the A/T assembly to check component parts. Refer to 

TM-226, "Disassembly"

.

NOTE:
Check the component parts, referring to “Possible cause” in “DTC DETECTION LOGIC”. Refer to 

TM-120,

"DTC Logic"

.

Is the inspection result normal?

YES

>> Replace the control valve & TCM. Refer to 

TM-182, "Exploded View"

.

NO

>> Repair or replace damaged parts.

GEAR

: 2nd

ACCELE POSI

: 0.7/8 or more

VEHICLE SPEED

: 10 km/h (7 MPH) or more

Selector lever

: “M” position

Gear position

: 2nd

Accelerator pedal opening

: 0.7/8 or more

Vehicle speed

: 10 km/h (7 MPH) or more

TM-122

< DTC/CIRCUIT DIAGNOSIS >

[7AT: RE7R01B]

P0733 3GR INCORRECT RATIO

P0733 3GR INCORRECT RATIO

Description

INFOID:0000000006226827

This malfunction is detected when the A/T does not shift into 3GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.

DTC Logic

INFOID:0000000006226828

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

• “

TM-123, "Diagnosis Procedure"

” must be performed before starting “DTC CONFIRMATION PROCE-

DURE”.

• Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause

secondary malfunction.

• Always drive vehicle at a safe speed.

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” is previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.

>> GO TO 2.

2.

CHECK ATF TEMPERATURE

 With CONSULT-III

1.

Start the engine.

2.

Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.

3.

Check ATF temperature is in the following range.

 With GST

1.

Start the engine.

2.

Drive vehicle for approximately 5 minutes in urban areas.

Is ATF temperature within specified range?

YES

>> GO TO 3.

NO

>> Drive vehicle to warm ATF or stop engine to cool ATF.

3.

CHECK SYMPTOM (PART 1)

 With CONSULT-III

1.

Select “3RD GR FNCTN P0733” in “DTC & SRT confirmation” in “TRANSMISSION”.

2.

Drive vehicle with manual mode and maintain the following conditions.

DTC

Trouble diagnosis name

DTC is detected if...

Possible cause

P0733

Gear 3 Incorrect Ratio

The gear ratio is:
• 2.148 or more
• 1.906 or less

• Input clutch solenoid valve
• Direct clutch solenoid valve
• High and low reverse clutch 

solenoid valve

• Front brake solenoid valve
• Low brake solenoid valve
• 2346 brake solenoid valve
• Anti-interlock solenoid valve
• Each clutch and brake
• Output speed sensor
• Input speed sensor 1, 2
• Hydraulic control circuit

ATF TEMP 1

: 20

°

C (68

°

F) – 140

°

C (284

°

F)

P0733 3GR INCORRECT RATIO

TM-123

< DTC/CIRCUIT DIAGNOSIS >

[7AT: RE7R01B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

3.

Keep the current driving status for 2 seconds or more if CONSULT-III screen changes from “OUT OF
CONDITION” to “TESTING”.

CAUTION:

When “TESTING” is not indicated on CONSULT-III for a long time, check “Self Diagnostic Results”
in “TRANSMISSION”. When a DTC other than “P0733” is detected, check the DTC. Refer to 

TM-78,

"DTC Index"

.

 With GST

1.

Drive vehicle and maintain the following conditions for 2 seconds or more.

2.

Check DTC.

Is  “OUT OF CONDITION”,  “STOP VEHICLE” or “COMPLETED RESULT NG” displayed? / Is “P0733”
detected?

YES-1 (OUT OF CONDITION)>>Perform “Step 3” again.
YES-2 (STOP VEHICLE)>>GO TO 4.
YES-3 (COMPLETED RESULT NG)>>Go to 

TM-123, "Diagnosis Procedure"

.

YES-4 (“P0733” is detected)>>Go to 

TM-123, "Diagnosis Procedure"

.

NO

>> GO TO 4.

4.

CHECK SYMPTOM (PART 2)

1.

Stop vehicle.

2.

Drive vehicle in “D” position allowing it to shift from 1GR to 7GR and check shift timing and shift shock.

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000006226829

1.

DETECT MALFUNCTIONING ITEM

Disassemble the A/T assembly to check component parts. Refer to 

TM-226, "Disassembly"

.

NOTE:
Check the component parts, referring to “Possible cause” in “DTC DETECTION LOGIC”. Refer to 

TM-122,

"DTC Logic"

.

Is the inspection result normal?

YES

>> Replace the control valve & TCM. Refer to 

TM-182, "Exploded View"

.

NO

>> Repair or replace damaged parts.

GEAR

: 3rd

ACCELE POSI

: 0.7/8 or more

VEHICLE SPEED

: 10 km/h (7 MPH) or more

Selector lever

: “M” position

Gear position

: 3rd

Accelerator pedal opening

: 0.7/8 or more

Vehicle speed

: 10 km/h (7 MPH) or more

TM-124

< DTC/CIRCUIT DIAGNOSIS >

[7AT: RE7R01B]

P0734 4GR INCORRECT RATIO

P0734 4GR INCORRECT RATIO

Description

INFOID:0000000006226830

This malfunction is detected when the A/T does not shift into 4GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as control
valve sticking, improper solenoid valve operation, etc.

DTC Logic

INFOID:0000000006226831

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

• “

TM-125, "Diagnosis Procedure"

” must be performed before starting “DTC CONFIRMATION PROCE-

DURE”.

• Never perform “DTC CONFIRMATION PROCEDURE” before completing the repair, which may cause

secondary malfunction.

• Always drive vehicle at a safe speed.

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” is previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.

>> GO TO 2.

2.

CHECK ATF TEMPERATURE

 With CONSULT-III

1.

Start the engine.

2.

Select “ATF TEMP 1” in “Data Monitor” in “TRANSMISSION”.

3.

Check ATF temperature is in the following range.

 With GST

1.

Start the engine.

2.

Drive vehicle for approximately 5 minutes in urban areas.

Is ATF temperature within specified range?

YES

>> GO TO 3.

NO

>> Drive vehicle to warm ATF or stop engine to cool ATF.

3.

CHECK SYMPTOM (PART 1)

 With CONSULT-III

1.

Select “4TH GR FNCTN P0734” in “DTC & SRT confirmation” in “TRANSMISSION”.

2.

Drive vehicle with manual mode and maintain the following conditions.

DTC

Trouble diagnosis name

DTC is detected if...

Possible cause

P0734

Gear 4 Incorrect Ratio

The gear ratio is:
• 1.496 or more
• 1.328 or less

• Input clutch solenoid valve
• Direct clutch solenoid valve
• High and low reverse clutch 

solenoid valve

• Front brake solenoid valve
• Low brake solenoid valve
• 2346 brake solenoid valve
• Anti-interlock solenoid valve
• Each clutch and brake
• Output speed sensor
• Input speed sensor 1, 2
• Hydraulic control circuit

ATF TEMP 1

: 20

°

C (68

°

F) – 140

°

C (284

°

F)